Victory 4x4 200 Series Configuration guide

200 SERIES
LAND CRUISER
ROOF RACK
Thank you for purchasing from Victory 4x4! Checkout our website, victory4x4.com for other great o-road
products. Be sure to rate and review our product online. If you have any questions or are missing parts, please
don’t hesitate to call us at 269-459-8447!
INSTALL INSTRUCTIONS
Please read the mounting instructions below carefully before attempting to install.
Check out the install video on the product page for factory rack disassembly.

INCLUDED HARDWARE
54x
22x
54x
1/4” ID
Washer
1/4"-20
Serr. Flange Nut
1/4"-20 X 3/4"
Button Head
4x
1/4"-20 X 3/8"
Button Head
4x 1/4"-20
T-Nut
12x M8
Washer
12x
25mm M8
Button Head
Included with light
bar cutout option.
Included with light
bar cutout option.
4x
4x
5/16”
Flanged Nylock Nut
5/16” -18 X 1”
Elevator Bolt

INCLUDED PARTS
2x 8x 1x 1x 1x
Or
1L/1RIncluded with light
bar cutout option.
2x
1L/1R
2x 2x

1Assemble the rack on the ground. Start by mounting the crossbars
between the 2 side rails. For this, use the 1/4”-20 X 3/4” button head bolts
and the 1/4” ID washers (2 per bar per side). Make sure the machined slot
in the rail of the crossbar is facing up, so that you can easily add t-nuts to
mount your gear.
ASSEMBLY

ASSEMBLY
2Next, mount the strip of trim to the bottom edge of the front fairing. Start
just to the outside of the peak of the bottom edge and continue until it
reaches the equivalent point on the other side of the fairing. Cut o any
extra. Then, cut the extra in half and mount the 2 pieces onto the bottom
edge of the rear fairing wherever it contacts the roof of the vehicle.

ASSEMBLY
3Next, mount the front and rear fairings. To do this, use the 1/4”-20 X 3/4”
button head bolts, 1/4” ID washers, and 1/4”-20 serrated flange nuts. The
front fairing will need three of each per side and the rear fairing will need
two of each per side. When mounting the front fairing, adjust it all the way
up to avoid contact with the roof and leave the bolts loose enough to be
able to make adjustments once it is on the roof of the vehicle.

ASSEMBLY
4Next, assemble the two halves of the front mounts. The side of the
unlabeled bracket with the wider slots sits flat against the top of the of
the brackets labeled with an F. It should be oriented so that the side with
the smaller slots is above the flange with the letters cut out and pointing
up. Then, insert the 5/16”-18 X 1” elevator bolt through the square hole,
making sure that the square neck of the bolt sits inside the hole and fasten
them using the 5/16”-18 nylock nuts. Leave this loose for now so you can
make adjustments later.

ASSEMBLY
5Next, attach the mounts to inside of the rack using the 1/4”-20 X 3/4”
button head bolts, 1/4” ID washers, and 1/4”-20 serrated flange nuts.
The labeled flange on the mid and rear mounts should point towards the
middle of the vehicle. On the front mounts, it should point towards the
outside. The front and mid mounts are symmetrical and can go on either
side. The rear mounts have an arrow on them that should be pointing
towards the front of the vehicle.

ASSEMBLY
6Next, apply RTV around the mounting holes on the roof of the vehicle
and set the assembled rack into place. Try to get it as close to the correct
position as possible so that you don’t accidentally spread the RTV while
trying to sliding the rack into position. Then, cover and fill the top of the
mounting holes with more RTV so that the bolts will have to pass through
it when tightening the mount in to place. Next, tighten it fully into place
with the M8 bolts and M8 washers.

ASSEMBLY
7
8Finally, push the front and rear fairing down tight to the roof of the vehicle
and tighten everything fully into place. We recommend applying clear 3M
paint protection film to the roof of the vehicle anywhere the edge trim/
fairings make contact with the roof. This will protect the paint from dirt/
debris over time.
With everything in place, make whatever adjustments that are necessary
in order to get an even gap between the bottom edge of the rack and the
roof, all the way down the length of the vehicle and then tighten it into
place. Tighten the mounts to the vehicle first, then tighten the mid and
rear mounts to the rack. Then, make sure the top part of the front mount
is flat against the rail and tighten the elevator bolts, followed by the bolts
into the side rail.

40” LIGHT BAR
ASSEMBLY
1Slide 2 t-nuts into each of the channels on the top side of the front-most
crossbar using the slots. Then, place each light bar mount over one pair of
t-nuts and loosely bolt it in place using the 1/4”-20 X 3/8” button heads.
2Next, place your light bar between the mounts and mount it in the slots
using the hardware provided with the light bar. Aer that is firmly in
position, make any adjustments to the positioning necessary to center the
light bar on the rack. Depending on the rack and light bar, you may need to
adjust the position of the cross bar in its slot as well.

DIMENSIONS