Yealink Telkom W52P User manual

Barracuda Phone System
Yealink W52P Wireless DECT IP Telephone Quick Reference Guide
1 / 5
Yealink W52P Wireless DECT IP Telephone Quick
Reference Guide
This article explains the basic operation of the Yealink W52P Wireless DECT IP telephone.
Yealink Model W52P Wireless DECT Phone and Base Station
Soft Keys
The two buttons immediately below the LCD display are soft keys.
Each soft key performs the action displayed immediately above it.
Soft key behavior is context sensitive – the associated soft key action changes according to the current
phone state.
Place a Call
Dial the number, then press the green off-hook key.
Redial
To redial the last number, press the green off-hook key twice.
To view previously dialed numbers, press the green off-hook key once and then use the up and down
arrow keys to scroll through the list. Press the green off-hook key to dial the highlighted phone number.
Voicemail Access
To access voicemail messages, dial *98 and press the green off-hook key.
Depending on your system configuration, you may be prompted for a voicemail PIN number.

Barracuda Phone System
Yealink W52P Wireless DECT IP Telephone Quick Reference Guide
2 / 5
Call Hold
To place an existing call on hold, press the Options soft key then press the Hold soft key.
To retrieve a call on hold, press the Resume soft key.
If two calls are on hold, press the Resume soft key to resume the current call. Use the up/down arrows or
the Swap soft key to swap between the calls.
Call Transfer
To transfer a call that is in progress, press the Options soft key and select either Blind
Transfer or Transfer (for an attended transfer).
Dial the destination number, then press OK.
For a blind transfer, the operation is complete.
For an attended transfer, wait for the destination party to answer, then announce the caller.
Press the Transfer soft key to complete the transfer.
3-Way Calling
Place (or receive) a call.
To add another party to the call, press the Options soft key and select Conference.
Dial the destination number, then press OK.
When the destination party answers, press the Conf. soft key.
Press the red hangup button to end the conference call.
Call Forwarding
When your phone is idle, press OK > > Call Forward. The display will show the lines assigned to the
handset.
Press the up/down arrows to select the desired line, then press OK.
Press the up/down arrows to choose the call forward type, then press OK.

Barracuda Phone System
Yealink W52P Wireless DECT IP Telephone Quick Reference Guide
3 / 5
Select Enabled, then enter the destination number in the Target field.
Press the Save soft key to accept the changes.
To cancel call forwarding, follow the same steps and select Disabled in the Status field.
Volume Control
When your phone is idle, press the left/right arrow keys to decrease or increase volume, then press
the Save soft key.
During an active call, left/right arrow keys will change the volume of the handset, speakerphone or
headset, whichever is active.
Base Station Setup and Handset Registration
Follow these steps to configure the base station and to register handsets.
Base Station Diagram
Page key1.
Registration LED2.
Network Status LED3.
Power Indication LED 4.
Base Station Installation
Choose a suitable location for the base station. The base station will need to be near the center of the
wireless coverage area.
Connect the base station to the local area network (LAN) with an Ethernet cable. The unit can be powered
with the supplied A/C adapter or with a power over Ethernet (PoE) port.
If you have automatic provisioning enabled on the Barracuda Phone System and the base station is on
the same subnet as the Barracuda Phone System, then the base station will be updated and five new
unassigned phones will now be available.
NOTE: Some W52P base stations ship with a firmware that does not support automatic provisioning. If this is
the case, you will need to manually provision the device. (Instructions below.)

Barracuda Phone System
Yealink W52P Wireless DECT IP Telephone Quick Reference Guide
4 / 5
Handset Registration
Place the supplied rechargeable batteries into the handset.
Charge the handset on the cradle until the charging status icon shows a full charge. Wait until the
handset is fully charged before continuing.
At the base station, press and hold the key for about four seconds. The registration LED will flash
slowly, indicating that the base station is in registration mode.
On the handset, press OK then select > Registration > Register Handset.
Use the up and down arrow keys to select the base station and press OK.
Press OK when the display shows the ID of the base station.
Enter the PIN number: 0000
Press Done key.
The handset will be assigned the next available handset ID, i.e. 1, 2, 3, 4, or 5.
Base Station Manual Provisioning
To manual provision your base station, you will need to know the IP address. You can retrieve this from a
registered handset by pressing OK > Status > OK > System Status > OK.
Log in to the Yealink user interface. The url is http://x.x.x.x[1] where x.x.x.x is the IP address of the Yealink.
The default login is Navigate to Phone > Auto Provision. In the Server URL field enter the
value http://x.x.x.x/provision/yealink/W52P[2], where x.x.x.x is the IP address of the Barracuda Phone
System.
username = admin
password = admin
Click the Confirm button, then power cycle the base station. When the base station boots back up it will
provision to the Barracuda Phone System.
It may take several minutes for the base station to completely provision.

Barracuda Phone System
Yealink W52P Wireless DECT IP Telephone Quick Reference Guide
5 / 5
Links