ACME LP-F1000 CW User manual

User Manual
Please read the instruc on carefully before use
LP-F1000 CW
LP-F1000 WW
2018.06.25
审核
受控正本

CONTENTS
1. Safety Introductions.............................................................................................. 2
2. Technical Specifications......................................................................................... 3
3. How To Set The Fixture ......................................................................................... 4
3.1 Control Panel................................................................................................... 4
3. 2 The Plate for Barn Door Installation ............................................................... 5
4. How To Control The Unit ..................................................................................... 10
4.1 Master/Slave Function .................................................................................. 11
4.2 DMX Controller ............................................................................................. 11
4.3. DMX512 Configuration................................................................................. 12
4.4. DMX512 Connections................................................................................... 13
5. Troubleshooting .................................................................................................. 14
6. Fixture Cleaning .................................................................................................. 14
1C

1. Safety Introductions
WARNING
Please keep this User Manual for future consultation. If you sell the unit to another user, be sure
that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the unit.
Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
The unit is for indoor use only. Use only in a dry location.
The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces. Be sure that no ventilation slots are blocked.
Disconnect main power before replacement or servicing.
Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
Use safety cables when fixing this unit.
Maximum ambient temperature is Ta: 40 degrees C. DO NOT operate it where the temperature
is higher than this.
Turn off the power and allow about 15 minutes for the unit to cool down before servicing.
In the event of a serious operating problem, stop using the unit immediately. Never try to repair
the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.
Please contact the nearest authorized technical assistance center. Always use the same type
spare parts.
DO NOT touch any cables during operation as high voltage may cause electric shock.
Warning:
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
The housing and lenses must be replaced if they are visibly damaged.
Please read the instructions carefully which includes important
information about the installation, operation and maintenance.
2C

Caution:
There are no user serviceable parts inside the unit. Do not open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your nearest
dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is
firmly fixed to avoid vibration and slipping while operating. Make sure that the structure to which
you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s
weight. Also always use a safety cable that can hold 12 times of the weight of the unit when
installing the fixture.
The equipment must be installed by professionals. It must be fixed at a place where is out of the
reach of people and no one pass by or under it.
2. Technical Specifications
Power Voltage: AC 100 ~ 240V, 50/60Hz
Power Consumption: 100W
Light Sources: 240 pcs CW LED (LP-F1000 CW)
240 pcs WW LED (LP-F1000 WW)
Color Temperature: 3200±150K
5600±250K
Beam Angle
：
130°
CRI
：
≥94
Weight: 9.2Kgs
Dimension: 673 x 306 x 144mm
3C

306
673
144
3. How To Set The Fixture
3.1 Control Panel
1
2345678
1. Display: Shows the various menus and the selected functions.
2. Button:
MENU
To select the programming functions
DOWN
To go backward in the selected functions
UP
To go forward in the selected functions
ENTER To confirm the selected functions
3. Dimmer Knob: Adjust the dimmer;
4. Mains In: Connects to mains supply power;
5. Fuse (T2A): To protect the unit from damage of over current;
6. Battery DC48V: Connects to external battery;
7. DMX IN/OUT : For DMX 512 link, use 5-pin XLR cable to link the unit to a DMX controller or the
next unit and output DMX signal;
8. ETHERNET:
4C

Connect with the multimedia and use software to control the units via ArtNet;
3. 2 The Plate for Barn Door Installation
At first, please push the barn door by hand.
Screw
Secondly, please put the Barn Door into the unit, to fasten the screws of the slot, then finish the
barn door installation.
3.3 Main Function
To select any of the given functions, press the MENU button up to the required selection as shown
on the display. Select the function with the ENTER button and the display will blink. Use the
DOWN/UP buttons to change the mode. Once the required mode has been selected, press the
ENTER button to confirm. To go back to the main functions without any changes press the MENU
button again. Press and hold the MENU button for about one second or wait for 7 seconds to exit
the current mode.
The main functions are shown below:
5C

DMX Address
Channel Mode
1 CH
DMX Setting A Setup
rt -Net
Slave Mode
Slave
Master
Dimmer Curve Square Law Curve
Linear Curve
S Curve
DMX State
IP Address
Net
0
Sub-Net
255
0
15
Universe
3 CH
Invert Square Law Curve
D immer Speed
Smooth
F avt
1
512
Blackout
Master Slave
Hold
2 CA H
2 CB H
6C

Display Setting
Backlight Auto Off
Contrast Ratio
Invert Display
1
30
N
o
Y ev
N
o
Y
ev
Firmware Version
Fixture Time
N
o
Y
ev
Language
Englivh
Chinese
Manual Mode
0
255
Dimmer
DMX Setting
Select the DMX Setting, press the ENTER button to confirm. Use the UP and DOWN button to
select DMX Address, Art-Net Setup or Channel Mode.
DMX Address
Select the DMX Address, press the ENTER button to confirm, the display will show the present
address. Use the UP and DOWN button to select 1to 512, press the ENTER button to store.
Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.
Art-Net Setup
Select the Eth-Net Address, press the ENTER button to confirm. Use the UP and DOWN button
to select the address for EtherNet IP Setup or ArtNet Port Setup,press the ENTER button to set
the value for these items. Press the MENU button back to the last menu or idling 30 seconds to
exit menu mode.
Channel Mode
Select the Channel Mode, press the ENTER button to confirm, the display will show the present
channel mode. Use the UP and DOWN button to select 1 CH, 2A CH, 2B CH or 3 CH, press the
ENTER button to store. Press the MENU button back to the last menu or idling 30 seconds to
7C

exit menu mode.
Dimmer Speed
Select the Dimmer Speed, press the ENTER button to confirm, use the UP and DOWN button to
select the Fast or Smooth mode, press the ENTER button to store. Press the MENU button back to
the last menu or idling 30 seconds to exit menu mode.
Dimmer Curve
Select Dimmer Curve, press the ENTER button to show the DIMMER CURVE on the display. Use
the DOWN/UP button to select the Mode 1,Mode 2, Mode 3 or Mode 4. Once the dimmer mode
has been selected, press the ENTER button to setup, to go back to the functions without any
change press the MENU button again. Press and hold the MENU button for about one second or
wait for one minute to exit the menu mode.
Mode 1(Optically Linear):
The increase in light intensity appears to be linear as DMX value is increased.
Mode 2(Square Law):
Light intensity control is finer at low levels and coarser at high levels.
Mode 3(Inverse Square Law):
Light intensity control is coarser at low levels and finger at high levels.
Mode 4(S-cure):
Light intensity control is finger at low levels and high levels and coarser at medium levels.
Slave Mode
Select the Slave Mode, press the ENTER button to confirm, use the UP and DOWN button to
select the Master or Slave mode, press the ENTER button to store. Press the MENU button back to
8C

the last menu or idling 30 seconds to exit menu mode.
DMX State
Select DMX State, press the ENTER button to confirm, the present mode will blink on the display,
use the UP and DOWN button to select Master Slave, Blackout or Hold,press the ENTER button to
store. Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.
Frequency
Select Frequency,press the ENTER button to confirm, the present mode will blink on the display,
use the UP and DOWN button to select 900hz, 1000hz , 1100hz , 1200hz , 1300hz , 1400hz ,
1500hz , 2500hz , 4000hz , 5000hz , 10000hz , 15000hz , 20000hz or 25000hz,press the ENTER
button to store. Press the MENU button back to the last menu or idling 30 seconds to exit menu
mode.
Display Setting
Select Display Setting, press the ENTER button to confirm, use the UP and DOWN button to select
Contrast Ratio, Backlight Auto off , Invert Display or Language.
Contrast Ratio
Select Contrast Ratio, press the ENTER button to confirm, the present mode will blink on the
display, use the UP and DOWN button to adjust from 1 to 30,press the ENTER button to store.
Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.
Backlight Auto Off
Select Backlight Auto Off, press the ENTER button to confirm, the present mode will blink on
the display, use the UP and DOWN button to select No or Yes,press the ENTER button to store.
Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.
Invert Display
Select Invert Display, press the ENTER button to confirm, the present mode will blink on the
display, use the UP and DOWN button to select No or Yes,press the ENTER button to store.
Press the MENU button back to the last menu or idling 30 seconds to exit menu mode.
9C