AGV INSYDE User manual

PHONE
Volume -
Quick start guide
Dainese S.p.A.
via Louvigny, 35
36064 Colceresa (VI),
Italy
ph.: [phone]
fax: [phone]
www.agv.com INSYDE_QSG_ENG_20200520
A SSEMBLY |Make sure to perform a correct and safe assembly. Incorrect assembly can lead to dangerous situations while riding. In case of any doubts, ask your dealer to support.
1
1
Remove the two covers applied on the helmet:
Remove the two covers applied on the helmet:
using the specific tool
using the specific tool 1
provided, release
provided, release
the two clips of the back unit
the two clips of the back unit 2
and detach it;
and detach it;
release the clip of the headset
release the clip of the headset 3
and push it
and push it
downwards. Remove the right-side cheek pad
downwards. Remove the right-side cheek pad
4
(see the helmet user manual).
(see the helmet user manual).
GETTING STARTED
On/Off
Volume +
Mute
Use while charging
Flash
Bluetooth®
AGV INSYDE
Bluetooth®
AGV INSYDE
keyboard
keyboard
main unit
main unit
intercom mobilemedia
volume up volume down
LED
Default language is English. Language set can be changed
via the Cardo Connect app.
USB charging
USB charging
and firmware upgrade
and firmware upgrade
3
3
Apply the headset through the three hooking
Apply the headset through the three hooking
guides
guides
1
and hook the plastic clip placed on
and hook the plastic clip placed on
the lower side
the lower side
2
. Then be sure to thread its
. Then be sure to thread its
cable underneath the helmet base trim
cable underneath the helmet base trim
3
.
.
4
4
Connect the microphone and the speakers ca-
Connect the microphone and the speakers ca-
bles. Then, on the right side of the helmet, in-
bles. Then, on the right side of the helmet, in-
stall the microphone in two movements.
stall the microphone in two movements.
2
2
Install the back unit and thread its right side ca-
Install the back unit and thread its right side ca-
bles
bles
1
under the helmet base trim (use the tool if
under the helmet base trim (use the tool if
necessary). Move the retention system
necessary). Move the retention system
2
out be-
out be-
fore threading the cables. Attach the cover with the
fore threading the cables. Attach the cover with the
hole for the charging slot
hole for the charging slot
3
supplied with Insyde.
supplied with Insyde.
5
5
Drive the microphone cable through its own
Drive the microphone cable through its own
slot on the speaker’s housing.
slot on the speaker’s housing.
6
6
Install both the speakers
Install both the speakers
1
in their housing
in their housing
using the adhesive strap supplied. To install the
using the adhesive strap supplied. To install the
left speaker, lift the cheek pad first, then attach
left speaker, lift the cheek pad first, then attach
it making sure that all its press studs
it making sure that all its press studs
2
are
are
fixed (see the helmet user manual for the cheek
fixed (see the helmet user manual for the cheek
pad operations).
pad operations).
7
7
Insert the cables connectors
Insert the cables connectors
1
in the empty
in the empty
space between the outer shell and the polystyrene,
space between the outer shell and the polystyrene,
on the right side. Insert the microphone cable first,
on the right side. Insert the microphone cable first,
then the speakers one.
then the speakers one.
8
8
Detach the crown pad releasing its two snap
Detach the crown pad releasing its two snap
buttons
buttons
1
, then thread the left speaker cable
, then thread the left speaker cable
2
between the polystyrene and the crown pad. Then
between the polystyrene and the crown pad. Then
fix the crown pad, taking care not to damage the
fix the crown pad, taking care not to damage the
cables.
cables.
1”
x1 x1
x1
1”
Initiate pairing
1
5”
2Pair phone
Search for Bluetooth®devices 3Add a second phone/GPS
x2
4Pair phone
Search for
Bluetooth®devices
flash
4Pair GPS
x1
4A Search for
Bluetooth®devices
GPS
Paired successfullyEND Flash
Voice dial
x1
Redial
x2
Speed dial
Set via app
x3
Answer a call
Any of these three buttons
x1
Ignore a call
x1
Reject a call
2”
End a call
x1
PAIR MOBILE DEVICES
5”
Flash
Cancel pairing
x1
Start / Stop sharing call
Share a call with DMC group
Bridging active phone calls to the DMC group
OVERVIEW
1 1 1
2
1
3
2
3 2 2
3
22 1
1
4
11
2
cardosystems.com
[e-mail]
USA & Canada: 1-800-488-0363
International: [phone]
Register your device on cardosystems.com/update/ for
• Receive software update
• Customize the device
• ...and more!
Full version of the User manual available on
cardosystems.com/support
agv.com
USER MANUAL
• For easy configuration
• Remote control operation
• On-the-go setting customization
• Managing DMC groups
• Available on:
CARDO MOBILE APP
1
MAN00514 MANUAL INSTALLATION GUIDE AGV - ENGLISH_A01

DMC INTERCOM GROUPING USING DMC INTERCOM
SET A CARDO NON-DMC INTERCOM JOIN/CREATE A NON-CARDO INTERCOM GROUP
INTERCOM VOICE COMMANDS
Verify you are in DMC Mode
Create a DMC Group
Admin + all group members Admin + new member ONLY
MUSIC
On
Previous
Off
Next
x1 2”
x2 x1
SHARING AUDIO
Start / Stop sharing
(when in Bluetooth®mode)
2”
FACTORY RESET
5”
Flash
Join an existing DMC Group
1
5”
1
5”
Flash
Rapid flash
THEN ONLY ONE GROUP ADMIN
2
x1
2
x1
Flash
3Grouped successfully Flash
Talking - always on Bridge (add) a non-DMC passenger
Mute group Unmute group
2”
First, verify that passenger is paired
via Bluetooth®(see 2-way Bluetooth®
intercom pairing)
1
2
x1
Start / Stop bridging
Start / End / Add with rider 1
Rider 1
x1
Start / End / Add with rider 2
Rider 2
x2
1
2
Choose member for private chat
via Mobile App
Start / Stop chat
x2
DMC
ON
Buddy
1
Buddy
2
Private chat
Chat privately with one of the group members
Initiate a 4-way intercom Conference
Rider 1 You Rider 2 Rider 3
x1
Connect
to rider 1
x1
Connects
to rider 3
Connects
to rider 2
x2
“Hey Cardo, radio on”
“Hey Cardo, radio off”
“Hey Cardo, next station”
“Hey Cardo, previous station”
“Hey Cardo, music on”
“Hey Cardo, radio off”
“Hey Cardo, next track”
“Hey Cardo, previous track”
“Hey Cardo, volume up”
“Hey Cardo, volume down”
“Hey Cardo, mute audio”
“Hey Cardo, unmute audio”
“Hey Cardo, speed dial”
“Hey Cardo, redial number”
Anwser
Ignore
“Hey Siri”
“Hey Google”
“Hey Cardo, battery status”
“Hey Cardo, call intercom”
Bluetooth®/ DMC
Change intercom mode
Verify that you are
in Bluetooth®Mode x1 Flash
2-way
pairing 5”
Flash
You Rider 1 You
Initiate intercom pairing
Adding
3rd rider
Initiate intercom pairing
Rider 2YouRider 1
5”
Flash
You
x2
You
Flash
Adding
4th rider
Rider 2 connects to rider 3 on his free channel
Rider 2YouRider 1 Rider 3
2-way
pairing
Rider 1 You
Initiate intercom pairing
Adding
3rd rider
Initiate intercom pairing
Rider 2YouRider 1
5”
Flash
You
x2
You
Flash
5”
Flash
You You
x1
Flash
You
x1
Adding
4th rider
Rider 2 connects to rider 3 on his free channel
Rider 2YouRider 1 Rider 3
FM RADIO
On
x2
Off
2”
Previous
x2
Next
x1
Auto scan
2”
Stop scan
x1
Rapid flash
Cancel grouping
5”
Bluetooth®/ DMC
Change intercom mode
Verify that you are
in Bluetooth®Mode x1 Flash

front back
180 mm 180 mm
90 mm 90 mm
Measurements

TYPE APPROVAL
P/N MAN00514
DESCRIPTION POCKET GUIDE
FILE NAME MAN00514 MANUAL INSTALLATION GUIDE AGV - ENGLISH_A01
LANGUAGE Multi Lang
PRODUCT TYPE MANUAL
MATERIAL P2 C4+4
80gr offset folded
PRINTING
PROCESS COLOR: CMYK
SECONDARY
PROCESS
GLOSSY FINISH
ATTACHED
FILES
1. GRAPHIC FILE - PDF
2. Attached video for folding explanation
MEASUREMENT SPREAD: 360MM-540MM , FOLDED: 180MM-90MM
CLIENTS/
DISTRIBUTOR
SPECIAL
REQUIREMENT
REVISION DESCRIPTION DATE NAME
A01 FINAL- rst version 11.08.2020 DANNA