Akuvox R27 series User manual

1
R27X Door Phone User Manual

Content
1. Overview ................................................................................... 3
1.1. Product Description .........................................................................................3
1.2. Features............................................................................................................ 4
1.3. Keypad..............................................................................................................6
1.4. Installation........................................................................................................7
1.5. Unpacking......................................................................................................... 9
2. Configuration .......................................................................... 10
2.1 Basic setting in Phone interface......................................................................10
2.1.1 Status ....................................................................................................10
2.1.2 RF Card ..................................................................................................10
2.1.3 Private Key ............................................................................................10
2.1.4 Reset ..................................................................................................... 10
2.2 Web login ........................................................................................................11
2.2.1 Obtaining IP address .............................................................................11
2.2.2 Login the web........................................................................................11
2.2.3 Status-Basic ...........................................................................................12
2.2.4 Intercom-Basic ......................................................................................13
2.2.5 Intercom-Advanced...............................................................................14
2.2.6 Intercom-Relay&Input...........................................................................15
2.2.7 Intercom-Live Stream............................................................................16
2.2.8 Intercom-RTSP.......................................................................................17
2.2.9 Intercom-Onvif ...................................................................................... 18
2.2.10 Intercom-Card Setting(Optional) ........................................................19
2.2.11 Account-Basic...................................................................................... 20
2.2.12 Account-Advanced .............................................................................. 22
2.2.13 Network-Basic .....................................................................................25
2.2.14 Network-Advanced.............................................................................. 26
2.2.15 Phone-Time/Language........................................................................ 27
2.2.16 Phone-Call Feature.............................................................................. 28
2.2.17 Phone-Voice ........................................................................................29
2.2.18 Phone-Multicast.................................................................................. 31
2.2.19 Phone-Call log .....................................................................................32
2.2.20 Phone-Door log ...................................................................................33
2.2.21 Upgrade-Basic .....................................................................................34
2.2.21 Upgrade-Advanced.............................................................................. 35
2.2.22 Security-Basic ......................................................................................36

3
1.Overview
1.1. Product Description
R27C R27P
Akuvox R27X is a SIP-compliant handfree video outdoor phone. It can be connected
with your Akuvox IP Phone for remote unlock control and monitor. You can operate
the indoor handset to communicate with visitors via voice and video, and unlock the
door if you wish. User can also use RF card to unlock the door(Only R27C). It’s
applicable in villas, office and so on.

4
1.2. Features
Highlight
Vandal resistant body, with a flush button
Wild-angle camera:120°
POE(IEEE802.3af, Power-over-Ethernet)
Two-way audio communication over IP network with Echo cancel feature
Complies with SIP Standard for easy integration in each SIP PBXes
Complies with ONVIF standard for easy integration with any network surveillance
system
Physical&Power
Body material: all-aluminum
Camera: 3M pixels, automatic lighting
Numeric keypad with extra button buttons
Infrared Sensor: Support
Wiegand port: Support
RF Card Reader:13.56MHz & 125kHz
Output Relay: 3 output relays for door opener
802.3af Power-Over-Ethernet
12V DC connector(if not using POE)
Power consumption: less than 12w
Water proof&Dust proof: IP65
Installation: Flush-mounted
Dimension:280x128x68.5mm

5
SIP Endpoint
SIP v1(RFC2543), SIP v2(RFC3261)
Audio codecs: G.711a, G.711μ, G.722, G.729
Video codecs: H264
Speech Quality: 7kHz Audio
Echo Cancellation
Voice Activation Detection 
Comfort Noise Generator 
Video
Resolution: up to 1080p
Maximum image transfer rate:1080p-30pfs
High intensity white LEDs for picture lighting during dark hours with internal light
sensor
Compatible with 3rd.Party.Video components,e.g.NVRs.
Door Entry Feature
Relay control individually by DTMF tones
Camera permanently operational
White Balance: Auto
Auto-night mode with LED illumination
Minimum illumination: 0.1LUX
Network Features
1x10/100Mbps Ethernet Port
Protocols support: IPv4, HTTP, HTTPS, FTP, SNMP, DNS, NTP, RTSP, RTP, TCP, UDP,
ICMP, DHCP, ARP

6
1.3. Keypad
Key
Description
Numeric Key
Manage Center Key
Dialing Key
Delete Key

7
1.4. Installation
Dig out a square
hole(height*width*depth
=269.5*122.4*60.5mm)
Note: user need to make
the hole a little bigger
that can accommodate
all cables
Place the embedded box into
the hole. Use the pen to make
the cable location on the
embedded box.
Take down the
embedded box, use
5mm hand drill to make
the hole of cable
location you marked
before.
Use the pen to make
the cable location on
the embedded box.
Place the embedded box
into the square hole. Make
all cables go through the
hole of cable location. Use
6 ST4X20 screws to fix the
embedded box.
Note: the embedded box
can not over the edge of
the square hole.
Use 6 M4X10 screws to fix
the stand on the embedded
box.

8
Back cover installation:
Take out the back
cover ,cable buckle and
sealing ring
Make cables go through all the
components of the bottom hole of the
back cover , connect with the contacts in
the main board. Then put the cable buckle
and sealing ring into the back cover.
Use 4 M3x5 screws to fix the back cover

9
Device mounting:
1.5. Unpacking
Name
Quantity
R27C/P
1
Embedded box
1
Stand
1
M4X10 screw
6
ST4x20 screw
6
Screw fixing seat
6
M3X6 screw
2
M3X5 screw
4
Screwdriver
1
Place R27 into the stand. Push down
so that the device is fixed securely.
Lock the the M3X6 screws at the
bottom of device.

10
2.Configuration
2.1 Basic setting in Phone interface
Press 3888+Dialing key to enter basic setting interface in door phone.
2.1.1 Status
Press 1 to enter status interface to check IP address ,Mac address and Firmware
version of the door phone.
2.1.2 RF Card
This function is only for quick adding cards. Press 2 , then you will see “RF Key
Learning...”, place your card in the card sensor area. “RF Key Learning+1”means
adding successfully. If you want to do more modification about RF card, please
configure in website.
2.1.3 Private Key
Press 3 to modify the public password of door phone. When you see “Enter
password:”, please input the 8 digital password ,press Dialing key to confirm. The
default password is 33333333.
User just input “#+password+Dialing Key”t unlock the door.
2.1.4 Reset
Press 4 to reset the device.

11
2.2 Web login
2.2.1 Obtaining IP address
The Akuvox R27X uses DHCP IP by default. Press 3888 + Dialing Key to enter basic
setting interface. Enter Status to check the phone IP address.
2.2.2 Login the web
Open a Web Browser, enter the corresponding IP address. Then, type the default user
name and password to log in. The default User Name and Password are as below:
User name: admin
Password: admin

12
2.2.3 Status-Basic
Status, including product information, network information and Account information,
can be viewed from Status -> Basic.
Sections
Description
Product Information
To display the device’s information such as Model name,
MAC address (IP device’s physical address), Firmware version
and Hardware firmware.
Network Information
To display the device’s Networking status(LAN Port),such as
Port Type(which could be DHCP/Static/PPPoE), Link Status, IP
Address, Subnet Mask, Gateway, Primary DNS server,
Secondary DNS server, Primary NTP server and Secondary
NTP server(NTP server is used to synchronize time from
INTERNET automatically).
Account Information
To display device’s Account information and Registration
status (account username, registered server’s address,
Register result).

13
2.2.4 Intercom-Basic
Go to the path: Intercom-Basic
Sections
Description
Basic
Select Account: R27 supports 2 accounts. You can choose
one account or Auto mode for the following Intercom
basic settings.
No Answer Call：R27 will call to the No answer call
number in order when the ringtone is time out without
answer of the push button number. Disable by default.
Push Button
Push Button: To configure the destination number or IP
you want to contact with.
No Answer Call 1&2: To setup two no answer call
numbers or one no answer call number.
Web Call
To dial out or answer the phone from website.
Max Call Time
To configure the max call time
Max Dial Time
Dial in Time: When other phone calls to R27, if ring tone
is over the Dial in Time without answer. The call will be
hang up.

14
Dial out Time: When R27 calls to the other party, if the
ringtone is over the Dial out Time without answer. R27
will continue calls to no answer call number in order.
Push to Hang up
To enable or disable the Push to Hang up function
2.2.5 Intercom-Advanced
Sections
Description
AEC Level
AEC(Configurable Acoustic and Line Echo Cancelers) is used
to adjust the echo effect during the communication. The
default value is 700. Increase the level, the echo control is
better.
Photoresistor
Photosensitive is used to sense the light intensity that R27C
will auto enable infrared LED. Users can adjust the
photosensitive value by yourself.
Tamper Alarm
Enable the Tamper Alarm, if the gravity of R27 changes, the
phone will alarm. The Threshold value is smaller, the faster
the reaction of device.

15
2.2.6 Intercom-Relay&Input
Sections
Description
Private Key
Import or Export the Private Key template.
Relay
To configure some settings about unlock
Relay Select: R27 supports 2 relays
Relay Type: Different locks use different relay types, default
state or invert state. If you connect the Lock in NO
connector, select default state. Otherwise using invert
state.
Relay Delay(sec): Allows door remain “open”for certain
period The range is from 1 to 10 seconds
DTMF Option: R27 supports 1/4 digits DTMF unlock code.
Please select one type and enter the corresponding code.
DTMF: Setup 1 digit DTMF code for remote unlock
4 digital DTMF : Setup 4 digits DTMF code for remote
unlock.
Status: the status will be changed by the relay state.
Open Relay via HTTP
User can use a URL to remote unlock the door.
Switch: Enable this function. Disable by default.
Username & password : Users can setup the username and
password for HTTP unlock. Null by default
URL format:http://192.168.1.102/fcgi/do?action=OpenDoor&

16
2.2.7 Intercom-Live Stream
Sections
Description
Live Stream
To check the real-time video from R27X.
UserName=&Password=&DoorNum=1

17
2.2.8 Intercom-RTSP
Sections
Description
RTSP Basic
To active the RTSP function, then R27 can be monitored.
RTSP Stream
To enabled RTSP video and select the video codec. R27
supports H264video codec.
H.264 Video Parameters
H264: A video stream compression standard. Different from
H263, it provides an approximately identical level of video
stream quality but a half bit rate. This type of compression is
sometimes called MPEG-4 part 10.
To modify the resolution,framerate and bitrate of H264
MPEG4 Video Parameters
MPEG4: it is one of the network video image Compression
standard. It supports the maximum Compression ratio
4000:1. It is an important and common video function with
great communication application integration ability and less
core program space.
To modify the resolution,framerate and bitrate of MPEG4
MJPEG Video Parameters
MJPEG: called Motion Joint Photographic Experts Group. It is
a video encoding format.in which each image is compressed

18
separately by JPEG.MJPEG compression can produce high
quality video image and has a flexible configuration in video
definition and Compressed frames
To modify the resolution,framerate and bitrate of MJPEG
2.2.9 Intercom-Onvif
Sections
Description
Basic Setting
To setup the Onvif function parameters. It is used to connect
with the corresponding Onvif tool.
Onvif Mode: Two modes - Discoverable and
Non-discoverable. Discoverable by default. Only
Discoverable mode, then Onvif software can search R27.
User Name: To modify the user name you need. Admin
by default.
Password: To modify the password you want. Admin by
default.
Note: User name and password is used for authentication.

19
2.2.10 Intercom-Card Setting(Optional)
Sections
Description
Import/Export Card Data
To import or export the card data file. Only support .xml
format.
Card Status
Normal: Choose Normal mode when reading card.
Card Issuing: Choose Card Issuing mode when writing
card
Card Setting
IC Key DoorNum: R27X can support to connect 2 doors.
Choose one and add the valid card for unlock.
IC Key Name: To setup corresponding name for the card.
IC Key Code: Place the card in the R27 RF Card Read
area, then click Abtain button. After R27 read the card
code, click Add, the card information will show in the
Door Card Management list.
Door Card Management
Valid card information will show in the list. Users can tick the
current card information then delete one or all in the list.

20
2.2.11 Account-Basic
Sections
Description
SIP Account
To display and configure the specific Account settings.
Status: To display register result.
Display Name: Which is sent to the other call party for
display.
Register Name: Allocated by SIP server provider, used for
authentication.
User Name: Allocated by your SIP server provide, used
for authentication.
Password: Used for authorization.
SIP Server 1
To display and configure Primary SIP server settings.
Server IP: SIP server address, it could be an URL or IP
address.
Registration Period: The registration will expire after
Registration period, the IP phone will re-register
automatically within registration period.
SIP Server 2
To display and configure Secondary SIP server settings.