Amazone EDX 6000 TC User manual
Operating Manual
az
Precision airplanter
EDX 6000-TC
MG3983
BAH0047-7 09.19
Please read this operating
manual before initial
operation.
Keep it in a safe place fo
r
future use!
en
2 EDX 6000-TC BAH0047-7 09.19
Reading the instruction
manual and to adhere to it should not appear to
be inconvenient and superfluous as it is not
enough to hear from others and to realise that a
machine is good, to buy it and to believe that now
everything would work by itself. The person
concerned would not only harm himself but also
make the mistake of blaming the machine for the
reason of a possible failure instead of himself. In
order to ensure a good success, one must consider
the design of the object, in other words one must
make himself familiar with every aspect of the
machine and gain practice in handling the
machine. Only by doing so would you be satisfie
d
both with the machine and also with yourself. To
achieve this is the purpose of this instruction
manual.
Leipzig-Plagwitz 1872.
Identification data
EDX 6000-TC BAH0047-7 09.19 3
Identification data
Please insert the identification data of the implement. The
identification data are arranged on the rating plate.
Machine ID No.:
(ten digits)
Type: EDX 6000-TC
Permissible system pressure (bar): Maximum 210 bar
Year of manufacture:
Basic weight (kg):
Permissible total weight (kg):
Maximum load (kg):
Manufacturer's address
AMAZONEN-WERKE
H. DREYER GmbH & Co. KG
Postfach 51
D-49202
Tel.:
Fax:
E-mail:
Hasbergen, Germany
+ 49 (0) 5405 50 1-0
+ 49 (0) 5405 501-234
Spare part orders
Spare parts lists are freely accessible in the spare parts portal at
www.amazone.de.
Please send orders to your AMAZONE dealer.
Formalities of the operating manual
Document number: MG3983
Compilation date: 09.19
Copyright AMAZONEN-WERKE H. DREYER GmbH & Co. KG, 2014
All rights reserved.
Reprinting, even of sections, permitted only with the approval of
AMAZONEN-WERKE H. DREYER GmbH & Co. KG.
Foreword
4 EDX 6000-TC BAH0047-7 09.19
Foreword
Dear Customer,
You have chosen one of the quality products from the wide product
range of AMAZONEN-WERKE, H. DREYER GmbH & Co. KG. We
thank you for your trust in our products.
On receiving the implement, check to see if it has been damaged
during transport or if parts are missing. Using the delivery note, check
that the implement has been delivered in full, including any special
equipment ordered. Damage can only be rectified if problems are
claimed immediately.
Before initial operation, read and comply with the information in this
operating manual, and particularly the safety instructions. Only after
careful reading will you be able to benefit from the full scope of your
newly purchased implement.
Please ensure that all the implement operators have read this
operating manual before they put the implement into operation.
Should you have any questions or problems, please consult this
operating manual or contact your local service partner.
Regular maintenance and timely replacement of worn or damaged
parts increases the lifespan of your implement.
User evaluation
Dear Reader,
We update our operating manuals regularly. Your suggestions for
improvement help us to create ever more user-friendly operating
manuals. Send us your suggestions by fax.
AMAZONEN-WERKE
H. DREYER GmbH & Co. KG
Postfach 51
D-49202
Tel.:
Fax:
E-mail:
Hasbergen, Germany
+ 49 (0) 5405 50 1-0
+ 49 (0) 5405 501-234
Table of Contents
EDX 6000-TC BAH0047-7 09.19 5
1User information ........................................................................................ 10
1.1Purpose of the document ....................................................................................................... 10
1.2Location information in the operating manual ........................................................................ 10
1.3Presentations used ................................................................................................................ 10
2General Safety Instructions ...................................................................... 11
2.1Obligations and liability .......................................................................................................... 11
2.2Presentation of safety symbols .............................................................................................. 13
2.3Organisational measures ....................................................................................................... 14
2.4Safety and protective equipment ........................................................................................... 14
2.5Informal safety measures ....................................................................................................... 14
2.6User training ........................................................................................................................... 15
2.7Safety measures in normal operation .................................................................................... 16
2.8Danger from residual energy ................................................................................................. 16
2.9Maintenance and repair work, fault elimination ..................................................................... 16
2.10Design changes ..................................................................................................................... 16
2.10.1Spare and wear parts and aids .............................................................................................. 17
2.11Cleaning and disposal ............................................................................................................ 17
2.12Workstation of the operator .................................................................................................... 17
2.13Warning symbols and other markings on the machine .......................................................... 18
2.13.1Position of the warning signs and other markings ................................................................. 25
2.14Dangers in case of non-observance of the safety instructions .............................................. 27
2.15Safety-conscious working ...................................................................................................... 27
2.16Safety information for users ................................................................................................... 27
2.16.1General safety instructions and accident prevention instructions .......................................... 27
2.16.2Attached implements ............................................................................................................. 31
2.16.3Hydraulic system .................................................................................................................... 32
2.16.4Electrical system .................................................................................................................... 33
2.16.5Brake system ......................................................................................................................... 34
2.16.6Tyre ........................................................................................................................................ 35
2.16.7PTO shaft operation ............................................................................................................... 35
2.16.8Operation of the precision airplanter ...................................................................................... 36
2.16.9Cleaning, maintenance and repair ......................................................................................... 36
3Loading and unloading ............................................................................. 37
3.1Important information ............................................................................................................. 37
3.2Removal of individual implement components in order to comply with the permitted transport
height ..................................................................................................................................... 38
3.2.1Fastening the seed tube hoses .............................................................................................. 39
3.3Loading and unloading with a tractor ..................................................................................... 40
3.3.1Loading the attached implement ............................................................................................ 41
3.3.2Unloading the attached implement ........................................................................................ 42
4Product description ................................................................................... 43
4.1Overview of assembly groups ................................................................................................ 43
4.2Electronic monitoring and operation (optional) ...................................................................... 48
4.3Camera system (option) ......................................................................................................... 49
4.4Safety and protective equipment ........................................................................................... 49
4.5Overview – Supply lines between the tractor and the implement .......................................... 51
4.6Transportation equipment ...................................................................................................... 52
4.7Proper use .............................................................................................................................. 5 3
4.8Danger areas and danger points ........................................................................................... 54
4.9Rating plate and CE mark ...................................................................................................... 55
4.10Technical data ........................................................................................................................ 56
4.11Necessary tractor equipment ................................................................................................. 57
Table o
f
Contents
6 EDX 6000-TC BAH0047-7 09.19
4.12Noise production data ........................................................................................................... 58
5Structure and function .............................................................................. 59
5.1Radar ..................................................................................................................................... 61
5.2Service brake system ............................................................................................................ 62
5.2.1Safety chain for implements without brake system (optional) ............................................... 62
5.2.2Immobiliser ............................................................................................................................ 62
5.2.3Parking brake ........................................................................................................................ 63
5.2.4Dual-circuit pneumatic service brake system ........................................................................ 63
5.2.5Hydraulic service brake system ............................................................................................ 63
5.2.6Implements without their own brake system ......................................................................... 63
5.3AMATRON 3 control terminal ................................................................................................ 64
5.4Controlling the implement with the AMATRON 3 on-board computer .................................. 65
5.5Frame and implement sections ............................................................................................. 66
5.6Seed singling and spreading ................................................................................................. 67
5.6.1Singling drum ........................................................................................................................ 67
5.6.2Seed shutter .......................................................................................................................... 69
5.6.3Air baffle ................................................................................................................................ 70
5.6.4Seed scraper ......................................................................................................................... 71
5.6.4.1Seed scraper, mechanically adjustable................................................................................. 72
5.6.4.2Seed scraper, electrically adjustable ..................................................................................... 72
5.6.5Baffle plate (optional), for working on slopes ........................................................................ 73
5.6.6Digital seed fill level monitoring ............................................................................................. 73
5.6.7Blower fan for seed singling and fertiliser delivery ................................................................ 74
5.6.7.1Connecting the blower fan to the tractor hydraulic system ................................................... 75
5.6.7.2Connecting the blower fan to the on-board hydraulic system (optional) ............................... 75
5.6.8Double disc coulter ................................................................................................................ 76
5.6.8.1Seed placement depth .......................................................................................................... 76
5.6.8.2Coulter pressure (double disc coulter) .................................................................................. 77
5.6.8.3Ground contact pressure and intensity of press rollers ......................................................... 78
5.6.8.4Star clearer (optional) ............................................................................................................ 79
5.6.8.5Clod clearer (optional) ........................................................................................................... 79
5.6.8.6Carrier roller scraper (optional) ............................................................................................. 80
5.6.8.7Press roller scraper (only for fine seeds) .............................................................................. 80
5.7Fertiliser metering and application ........................................................................................ 81
5.7.1Fertiliser hopper .................................................................................................................... 81
5.7.1.1Digital fill level monitoring ...................................................................................................... 82
5.7.1.2Filling auger (optional) ........................................................................................................... 83
5.7.1.3Weighing system (optional) ................................................................................................... 83
5.7.2Fertiliser metering unit and injector sluice ............................................................................. 84
5.7.3Fertiliser quantity adjustment ................................................................................................ 85
5.7.4Calibration test ...................................................................................................................... 86
5.7.5Distributor head ..................................................................................................................... 86
5.7.6Single disc type fertiliser coulter ............................................................................................ 87
5.8Track marker ......................................................................................................................... 89
5.9Running gear with twin tyres (optional) ................................................................................. 90
5.10Implement wheel mark eradicator (optional) ......................................................................... 90
5.11Tractor wheel mark eradicator (optional) .............................................................................. 90
5.12Lighting of the work tools (optional) ...................................................................................... 91
5.13Pre-emergence marker (option) ............................................................................................ 92
6Start-up ...................................................................................................... 93
6.1Checking the suitability of the tractor .................................................................................... 94
6.1.1Calculating the actual values for the total tractor weight, tractor axle loads and load
capacities, as well as the minimum ballast ........................................................................... 95
6.1.1.1Data required for the calculation (hitched implement) .......................................................... 96
6.1.1.2Calculation of the required minimum ballasting at the front GV min of the tractor for assurance
of the steering capability ....................................................................................................... 97
6.1.1.3Calculation of the actual front axle load of the tractor TV tat ................................................... 97
6.1.1.4Calculation of the actual total weight of the combined tractor and implement ...................... 97
Table of Contents
EDX 6000-TC BAH0047-7 09.19 7
6.1.1.5Calculation of the actual rear axle load of the tractor TH tat .................................................... 97
6.1.1.6Tyre load capacity .................................................................................................................. 97
6.1.1.7Table ...................................................................................................................................... 98
6.1.2Requirements for tractor operation with attached implements .............................................. 99
6.1.3Implements without their own brake system .......................................................................... 99
6.2Securing the tractor/implement against unintentional start-up and rolling ........................... 100
6.3Installation instructions for hydraulic blower fan connection to tractor hydraulics ............... 101
7Coupling and uncoupling the implement .............................................. 102
7.1Dual-circuit pneumatic service brake system ...................................................................... 103
7.1.1Coupling the brake and supply lines .................................................................................... 105
7.1.2Uncoupling the supply and brake line .................................................................................. 107
7.1.3Control elements of the dual-circuit pneumatic service brake system:................................ 108
7.2Hydraulic service brake system ........................................................................................... 109
7.2.1Coupling the hydraulic service brake system ...................................................................... 110
7.2.2Uncoupling the hydraulic service brake system ................................................................... 112
7.3Hydraulic hose lines ............................................................................................................. 113
7.3.1Coupling the hydraulic hose lines ........................................................................................ 113
7.3.2Uncoupling the hydraulic hose lines .................................................................................... 114
7.4Coupling the implement to the tractor .................................................................................. 114
7.5Aligning a towed implement ................................................................................................. 120
7.6Uncoupling the implement ................................................................................................... 121
7.7Coupling the hydraulic pump ............................................................................................... 124
7.7.1Connecting the hydraulic pump ........................................................................................... 124
7.7.2Uncoupling the hydraulic pump............................................................................................ 125
8Settings ..................................................................................................... 126
8.1Seed metering and application ............................................................................................ 127
8.1.1Adjusting the seeding rate ................................................................................................... 127
8.1.2Setting the seed shutter ....................................................................................................... 127
8.1.3Adjusting the air guide ......................................................................................................... 128
8.1.4Setting the seed scraper ...................................................................................................... 129
8.1.5Adjusting the seed placement depth .................................................................................... 130
8.1.6Setting the coulter pressure ................................................................................................. 131
8.1.7Closing the seed furrow by adjusting the press roller .......................................................... 132
8.1.8Adjusting the star clearers ................................................................................................... 132
8.1.9Adjusting the clod clearers ................................................................................................... 133
8.1.10Adjusting the carrier roller scraper ....................................................................................... 133
8.1.11Adjusting the press roller scraper ........................................................................................ 133
8.1.12Checking the placement depth and grain spacing ............................................................... 134
8.2Fertiliser metering and application ....................................................................................... 135
8.2.1Repositioning the fill level sensor ........................................................................................ 135
8.2.2Installing/removing the metering roller ................................................................................. 136
8.2.3Setting the fertilising rate using a calibration test ................................................................ 139
8.2.4Adjusting the fertiliser placement depth ............................................................................... 140
8.2.5Adjusting the furrow former on the fertiliser coulter ............................................................. 140
8.2.6Locking the fertiliser coulters ............................................................................................... 141
8.3Weighing system (optional) .................................................................................................. 142
8.3.1Taring the weighing equipment ............................................................................................ 142
8.3.2Calibration of the weighing equipment (specialist workshop) .............................................. 143
8.3.3Menu layout.......................................................................................................................... 145
8.4Adjusting the track marker length and working intensity ..................................................... 146
8.4.1Calculating the track marker length ..................................................................................... 147
8.5Adjusting the wheel mark eradicator .................................................................................... 147
8.6Adjusting the tractor wheel mark eradicator (optional) ........................................................ 148
8.7Adjusting fan speed ............................................................................................................. 149
8.7.1Adjusting the fan speed (connection to the tractor hydraulic system) ................................. 150
8.7.2Adjusting the fan speed (connection to the tractor PTO shaft) ............................................ 150
8.7.3Adjusting the fan speed (pressure relief valve) .................................................................... 151
8.7.4Basic setting (pressure relief valve) ..................................................................................... 152
Table o
f
Contents
8 EDX 6000-TC BAH0047-7 09.19
9Transportation ......................................................................................... 153
9.1Set the implement to road transport mode .......................................................................... 156
9.2Legal regulations ................................................................................................................. 159
10Use of the implement .............................................................................. 160
10.1Folding/unfolding the implement sections and track markers ............................................. 162
10.1.1Unfolding the implement sections ....................................................................................... 163
10.1.2Folding the implement sections ........................................................................................... 165
10.2Working without track markers ............................................................................................ 168
10.3Folding/unfolding the tractor wheel mark eradicators ......................................................... 169
10.3.1Moving the tractor wheel mark eradicator into working position ......................................... 169
10.3.2Moving the tractor wheel mark eradicators into transport position ..................................... 169
10.4Filling the hopper ................................................................................................................. 170
10.4.1Fill the seed hopper ............................................................................................................. 170
10.4.2Filling the fertiliser hopper ................................................................................................... 171
10.4.2.1Filling the fertiliser hopper with the filling auger .................................................................. 172
10.5Work commencement ......................................................................................................... 174
10.6During operation .................................................................................................................. 176
10.6.1Turning at end of the field ................................................................................................... 176
10.7End of work on the field ....................................................................................................... 178
10.7.1Emptying the seed hopper and/or seed singling unit .......................................................... 178
10.7.2Emptying the fertiliser hopper and the metering unit .......................................................... 181
10.7.3Emptying the fertiliser hopper ............................................................................................. 181
10.7.4Cleaning the metering unit .................................................................................................. 181
10.7.5Emptying the rest of the seeds from the filling funnel of the filling auger ............................ 184
11Faults ........................................................................................................ 186
11.1Residual quantity display .................................................................................................... 186
11.2Cleaning the seed tube ....................................................................................................... 187
11.2.1Cleaning the seed tube ....................................................................................................... 188
11.2.2Eliminating seed accumulations at the sealing lip ............................................................... 189
11.3Fault table ............................................................................................................................ 190
12Cleaning, maintenance and repairs ....................................................... 191
12.1Securing the connected implement ..................................................................................... 192
12.2Keep hopper with pellet filling closed .................................................................................. 192
12.3Cleaning the machine ......................................................................................................... 193
12.3.1Daily fast cleaning of the singling unit and the spur gears .................................................. 194
12.3.2Cleaning the supply hoses .................................................................................................. 195
12.3.3Deep cleaning of the implement .......................................................................................... 196
12.3.3.1Cleaning the fertiliser distributor head................................................................................. 197
12.3.3.2Cleaning the opto-sensor .................................................................................................... 197
12.4Removing/installing the singling drum................................................................................. 198
12.5Lubrication specifications .................................................................................................... 200
12.5.1Overview of lubrication points ............................................................................................. 200
12.6Maintenance schedule – overview ...................................................................................... 202
12.6.1Checking the seeding coulter discs ..................................................................................... 205
12.6.2Adjusting the spacing of the seeding coulter discs ............................................................. 206
12.6.3Adjusting the seeding coulter disc drive .............................................................................. 206
12.6.4Replacing the seeding coulter's furrow formers .................................................................. 207
12.6.5Checking the fertiliser coulter's coulter disc ........................................................................ 208
12.6.6Checking the fertiliser coulter furrow former ....................................................................... 209
12.6.7Checking the wear bushing on the support roller arm ........................................................ 209
12.6.8On-board hydraulics oil filter change ................................................................................... 210
12.6.9Visual inspection of the lower link pins................................................................................ 210
12.6.10Checking the inflation pressure of the running gear tyres................................................... 211
12.6.11Check tightening torques of wheel nuts (specialist workshop) ........................................... 212
12.6.12Relieving the hole covering rollers ...................................................................................... 213
12.6.13Pretensioning the hole-covering rollers ............................................................................... 214
Table of Contents
EDX 6000-TC BAH0047-7 09.19 9
12.6.14Hydraulic system (specialist workshop) ............................................................................... 215
12.6.14.1Labelling of hydraulic hose lines .......................................................................................... 216
12.6.14.2Maintenance intervals .......................................................................................................... 216
12.6.14.3Inspection criteria for hydraulic hose lines ........................................................................... 217
12.6.14.4Installation and removal of hydraulic hose lines .................................................................. 218
12.6.15Checking the brake drum for dirt (specialist workshop) ....................................................... 219
12.6.16Brake lining inspection (specialist workshop) ...................................................................... 219
12.6.17Adjusting the wheel brake on the slack adjuster (specialist workshop) ............................... 220
12.6.18Checking/adjusting the bearing clearance of the wheel hubs (specialist workshop) ........... 221
12.6.19Lubricating the axles ............................................................................................................ 222
12.7Service brake system (all variants) ...................................................................................... 223
12.7.1General visual inspection of the service brake system ........................................................ 223
12.7.2Checking the service brake system for safe operating condition (specialist workshop)...... 223
12.8Dual-circuit pneumatic service brake system ...................................................................... 224
12.8.1Exterior inspection of the compressed air tank .................................................................... 224
12.8.2Checking the pressure in the compressed air tank (specialist workshop) ........................... 224
12.8.3Leak tightness check (specialist workshop) ......................................................................... 225
12.8.4Cleaning the line filters (specialist workshop) ...................................................................... 225
12.9Hydro-pneumatic pressure reservoir (specialist workshop) ................................................. 226
12.10Bolt tightening torques ......................................................................................................... 227
13Hydraulic diagram .................................................................................... 228
13.1Hydraulic diagram for EDX 6000-TC ................................................................................... 228
13.2Hydraulic diagram for EDX 6000-TC with on-board hydraulic system ................................ 230
14Notes ......................................................................................................... 233
User information
10 EDX 6000-TC BAH0047-7 09.19
1 User information
The User information section provides information concerning the
operating manual.
1.1 Purpose of the document
This operating manual
describes the operation and maintenance of the implement
provides important information on safe and efficient handling of
the implement
is a component part of the implement and should always be kept
with the implement or the towing vehicle.
must be kept in a safe place for future use.
1.2 Location information in the operating manual
All the directions specified in the operating manual are always viewed
in the direction of travel.
1.3 Presentations used
Instructions and implement reactions
Activities to be carried out by the user are presented as numbered
instructions. Always observe the sequence of the instructions. The
reaction to instructions is given by an arrow. Example:
1. Instruction 1
→ Reaction of the implement to handling instruction 1
2. Instruction 2
Lists
Listings without a mandatory sequence are presented as a listing with
bullets. Example:
Point 1
Point 2
Item numbers in illustrations
Numbers in round brackets refer to the item numbers in the
illustrations. The first number refers to the figure and the second
number to the item.
Example: (Fig. 3/6)
Figure 3
Item 6
General Safety Instructions
EDX 6000-TC BAH0047-7 09.19 11
2 General Safety Instructions
This section contains important information on safe operation of the
implement.
2.1 Obligations and liability
Comply with the instructions in the operating manual
Knowledge of the basic safety information and safety regulations is a
basic requirement for safe handling and fault-free implement
operation.
Obligations of the operator
The operator is obliged only to let those people work with/on the
implement who
are aware of the basic workplace safety information and accident
prevention regulations
have received instruction in working with/on the implement.
have read and understood this operating manual.
The operator is obliged
to keep all the warning symbols on the implement in a legible
state
to replace damaged warning symbols.
Obligations of the user
Before starting work, anyone charged with working with/on the
implement is obliged
to comply with the basic workplace safety instructions and
accident prevention regulations
to read and understand the "General safety information" section
of this operating manual
to read the "Warning pictograms and other labelling on the
implement" section of this operating manual and to follow the
safety instructions of the warning pictograms when operating the
implement.
to get to know the implement
to read the sections of this operating manual, important for
carrying out your work.
If the user discovers that a function is not working properly, then they
must eliminate this fault immediately. If this is not the task of the user
or if the user does not possess the appropriate technical knowledge,
then they should report this fault to their superior (operator).
General Safety Instructions
12 EDX 6000-TC BAH0047-7 09.19
Risks in handling the implement
The implement has been constructed to the state-of-the art and the
recognised rules of safety. However, operating the implement may
cause risks and restrictions
the health and safety of the user or third persons
the implement itself
other property.
Only use the implement
for the purpose for which it was intended
in a perfect state of repair.
Eliminate any faults immediately which could impair safety.
Guarantee and liability
Our "General conditions of sales and delivery" are always applicable.
These shall be available to the operator, at the latest on the
completion of the contract. Guarantee and liability claims for damage
to people or property will be excluded if they can be traced back to
one or more of the following causes:
Improper use of the implement
Improper installation, commissioning, operation and
maintenance of the implement
Operation of the implement with defective safety equipment or
improperly attached or non-functioning safety and protective
equipment
Non-compliance with the instructions in the operating manual
regarding commissioning, operation and maintenance
Unauthorised design changes to the implement
Insufficient monitoring of implement parts which are subject to
wear
Improperly executed repairs
Disasters due to the effects of foreign objects and force majeure.
General Safety Instructions
EDX 6000-TC BAH0047-7 09.19 13
2.2 Presentation of safety symbols
Safety instructions are indicated by the triangular safety symbol and
the highlighted signal word. The signal word (DANGER, WARNING,
CAUTION) describes the severity of the risk, and carries the following
meaning:
DANGER
Indicates an immediate hazard with high risk, which will result
in death or serious bodily harm (loss of limbs or long-term
harm), if it is not avoided.
If the instructions are not followed, then this will result in
immediate death or serious physical injury.
WARNING
Indicates a hazard with medium risk, which could result in death
or (serious) physical injury if not avoided.
If the instructions are not followed, then this may result in death
or serious physical injury.
CAUTION
Indicates a hazard with low risk which could cause minor or
medium level physical injury or damage to property if not
avoided.
IMPORTANT
Indicates an obligation to special behaviour or an activity required for
proper implement handling.
Non-compliance with these instructions can cause faults on the
implement or disturbance to the environment.
NOTE
Indicates handling tips and particularly useful information.
These instructions will help you to use all the functions of your
implement in the best way possible.
General Safety Instructions
14 EDX 6000-TC BAH0047-7 09.19
2.3 Organisational measures
The operator must provide the necessary personal protective
equipment as per the information provided by the manufacturer of the
crop protection agent to be used, such as:
Safety glasses
Protective shoes
Chemical-resistant overalls
Skin protection agents, etc.
The operation manual
must always be kept at the place at which the implement is
operated
must always be easily accessible for the user and maintenance
personnel.
Check all the available safety equipment regularly.
2.4 Safety and protective equipment
Before starting up the implement each time, all the safety and
protection equipment must be properly attached and fully functional.
Check all safety and protection equipment regularly.
Faulty safety equipment
Faulty or disassembled safety and protection equipment can lead to
dangerous situations.
2.5 Informal safety measures
As well as all the safety information in this operating manual, comply
with the general, national regulations pertaining to accident prevention
and environmental protection.
When driving on public roads and routes you should comply with the
statutory road traffic regulations.
General Safety Instructions
EDX 6000-TC BAH0047-7 09.19 15
2.6 User training
Only those people who have been trained and instructed may work
with/on the implement. The operator must clearly specify the
responsibilities of the people charged with operation and
maintenance work.
People being trained may only work with/on the implement under the
supervision of an experienced person.
Person
Job
Person
specially trained
for the activity 1)
Trained
operator 2)
Person with specialist
training (specialist
workshop) 3)
Loading/Transport X X X
Start-up X
Set-up, tool installation X
operation X
Maintenance X
Troubleshooting and fault
elimination
X X
Disposal X
Legend: X..permitted
..not permitted
1) A person who can assume a specific task and who can carry out
this task for an appropriately qualified company.
2) Instructed persons are those who have been instructed in their
assigned tasks and in the possible risks in the case of improper
behaviour, have been trained if necessary, and have been
informed about the necessary protective equipment and
measures.
3) Persons with specialised technical training shall be considered
as a specialist. Due to their specialist training and their
knowledge of the appropriate regulations, they can evaluate the
work with which they have been charged and detect possible
dangers.
Comment:
A qualification equivalent to specialist training can be obtained
from several years' experience in the relevant field.
Only a specialist workshop may carry out maintenance and repair
work on the implement, if such work is additionally marked
"Specialist workshop". The personnel of a specialist workshop shall
possess the appropriate knowledge and suitable aids (tools, lifting
and support equipment) for carrying out the maintenance and repair
work on the implement in a way which is both appropriate and safe.
General Safety Instructions
16 EDX 6000-TC BAH0047-7 09.19
2.7 Safety measures in normal operation
Only operate the implement if all the safety and protection equipment
is fully functional.
Check the implement at least once a day for visible damage and
check the function of the safety and protection equipment.
2.8 Danger from residual energy
Note that there may be residual mechanical, hydraulic, pneumatic and
electrical/electronic energy on the implement.
Use appropriate measures to inform the operating personnel. You can
find detailed information in the relevant sections of this operating
manual.
2.9 Maintenance and repair work, fault elimination
Carry out prescribed setting, maintenance and inspection work in
good time.
Secure all media such as compressed air and the hydraulic system
against unintentional start-up.
Carefully fix and secure larger assembly groups to lifting gear when
carrying out replacement work.
Check all the bolted connections for tightness. On completion of the
maintenance work, check the function of the safety devices.
2.10 Design changes
You may make no changes, expansions or modifications to the
implement without the authorisation of AMAZONEN-WERKE. This
also applies when welding support parts.
Any expansion or conversion work shall require the written approval
of AMAZONEN-WERKE. Only use modification and accessory parts
approved by AMAZONEN-WERKE so that the type approval, for
example, remains valid in accordance with national and international
regulations.
Vehicles with an official type approval or with equipment connected to
a vehicle with a valid type approval or approval for road transport
according to the German road traffic regulations must be in the state
specified by the approval.
WARNING
Risk of crushing, cutting, being trapped or drawn in, or impact
through the failure of support parts.
It is strictly forbidden to
drill holes in the frame or on the running gear.
increase the size of existing holes on the frame or the running
gear.
weld on load-bearing parts.
General Safety Instructions
EDX 6000-TC BAH0047-7 09.19 17
2.10.1 Spare and wear parts and aids
Immediately replace any implement parts which are not in a perfect
state.
Use only genuine AMAZONE spare and wear parts or the parts
cleared by AMAZONEN-WERKE so that the operating permit retains
its validity in accordance with national and international regulations. If
you use wear and spare parts from third parties, there is no guarantee
that they have been designed and manufactured in such a way as to
meet the requirements placed on them.
AMAZONEN-WERKE shall accept no liability for damage caused by
the use of non-approved spare and wear parts or aids.
2.11 Cleaning and disposal
Handle and dispose of any materials used carefully, in particular
when carrying out work on lubrication systems and equipment
and
when cleaning using solvents.
2.12 Workstation of the operator
The implement may be operated by only one person sitting in the
driver's seat of the tractor.
General Safety Instructions
18 EDX 6000-TC BAH0047-7 09.19
2.13 Warning symbols and other markings on the machine
Always keep all the warning symbols of the implement clean and in a
legible state. Replace illegible warning symbols. You can obtain the
warning symbols from your dealer using the order number (e.g.
MD 075).
Warning symbols – structure
Warning symbols indicate danger areas on the implement and warn
against residual dangers. At these points, there are permanent or
unexpected dangers.
A warning symbol consists of two fields:
Field 1
is a symbol describing the danger, surrounded by triangular safety
symbol.
Field 2
is a symbol showing how to avoid the danger.
Warning symbols – explanation
The column Order number and explanation provides an explanation
of the neighbouring warning symbol. The description of the warning
symbols is always the same and specifies, in the following order:
1. A description of the danger.
For example: risk of cutting
2. The consequence of non-compliance with the risk avoidance
instructions.
For example: causes serious injuries to fingers or hands.
3. The risk avoidance instructions.
For example: only touch implement parts when they have come
to a complete standstill.
General Safety Instructions
EDX 6000-TC BAH0047-7 09.19 19
Order number and explanation Warning signs
MD 078
Risk of crushing of fingers/hand by
accessible, moving parts of the implement!
This hazard can cause the most severe injuries
with loss of body parts.
Never reach into the hazardous area while the
engine of the tractor with connected universal
joint shaft/hydraulic system/electronic system is
running.
MD 080
Risk of crushing of the entire body due to
standing in the swivel range of the drawbar
between the tractor and the attached
implement!
Causes serious, potentially fatal injuries
anywhere on the body.
Standing or walking in the danger area
between the tractor and implement is
prohibited whenever the tractor engine is
running and the tractor is not secured
against unintentional rolling.
Instruct people to leave the danger area
between the tractor and the implement
whenever the engine of the tractor is
running and the tractor is not secured
against unintentional rolling.
MD 082
Risk of falling when riding the implement on
treads or platforms!
Causes serious, potentially fatal injuries
anywhere on the body.
It is forbidden to ride on the implement or climb
the implement when it is running. This prohibition
also applies to implements with step surfaces or
platforms.
Make sure that nobody is riding on the
implement.
General Safety Instructions
20 EDX 6000-TC BAH0047-7 09.19
MD 083
Danger of arms being drawn in and/or caught
by moving parts involved in the working
process!
This hazard can cause the most severe injuries
with loss of body parts.
Never open or remove protective devices while
the tractor engine is running with the universal
joint shaft/hydraulic or electronic systems
connected.
MD 084
Risk of crushing the entire body due to
standing in the swivel range when implement
parts are being lowered.
Causes serious, potentially fatal injuries
anywhere on the body.
It is forbidden to stand in the swivel range of
the implement when implement parts are
being lowered.
Instruct personnel to leave the swivel range
of any implement parts which can be
lowered before you lower the parts.
MD 089
Risk of crushing the entire body due to
standing under suspended loads or raised
implement parts.
Causes serious, potentially fatal injuries
anywhere on the body.
It is forbidden to stand under suspended
loads or raised implement parts.
Maintain an adequate safety distance from
any suspended loads or raised implement
parts.
Ensure that all personnel maintain an
adequate safety distance from suspended
loads or raised implement parts.
Table of contents
Other Amazone Farm Equipment manuals
Amazone
Amazone Groundkeeper SmartCut GH 1350 User manual
Amazone
Amazone Hektor User manual
Amazone
Amazone Centaur 3002 User manual
Amazone
Amazone Catros 7003-2TS Installation instructions
Amazone
Amazone CatrosXL 4003-2 Installation instructions
Amazone
Amazone UX 6201 Super User manual
Amazone
Amazone KX Series User manual
Amazone
Amazone Ceus 3000-TX Installation instructions
Amazone
Amazone Avant 6002-2 Installation instructions
Amazone
Amazone Cirrus 3000 User manual
Amazone
Amazone Limiter M User manual
Amazone
Amazone CombiDisc 3000 Installation instructions
Amazone
Amazone Catros XL 7003-2TX User manual
Amazone
Amazone D9 2500 Special User manual
Amazone
Amazone EDX 6000-2 User manual
Amazone
Amazone TL 251 User manual
Amazone
Amazone Cenius 4003-2TX User manual
Amazone
Amazone Catros 3001 User manual
Amazone
Amazone EDX 9000-TC User manual
Amazone
Amazone Cayros M Installation instructions
Popular Farm Equipment manuals by other brands
Suevia
Suevia KRAZZMAXX IV Mounting and operation instructions
Mesko-Rol
Mesko-Rol Z 548 Service manual, Spare Parts
UNIA
UNIA TWISTER operating instructions
Sovema
Sovema PL 180 Operation and maintenance manual
Ferrari Costruzioni Meccaniche
Ferrari Costruzioni Meccaniche FPA NEXT Operating and service manual
Degelman
Degelman Pro-Till 33 Operator's & parts manual