Bradley Verge LVA Series User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
215-1851 Rev. A; ECN 17-08-002
© 2017 Bradley
Page 1 of 13 4/17/2017
LVAD3
Verge®Wash Basin – LVA-Series with
Evero®Natural Quartz Material
Table of Contents
Components ..................................................................3–4
Supplies Required .............................................................5
Dimensions....................................................................5–6
Rough-Ins .......................................................................7-8
Overflow Plug Assembly....................................................9
Drain Assembly .................................................................9
Faucets and Optional Soap Valve ...................................10
Bowl Mounting .................................................................10
Strainer and P-trap ..........................................................11
Adjust Temperature..........................................................11
Access Panel...................................................................12
Cleaning and Maintenance..............................................13

LVAD3 Installation
24/17/2017 Bradley • 215-1851 Rev. A; ECN 17-08-002
WARNING
Make sure that all water supply lines have been flushed and then completely turned off before beginning
installation. Debris in supply lines can cause valves to malfunction.
Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to installation. Electrical
power MUST remain off until installation is complete.
Installer's hardware must be appropriate for wall construction. Wall anchors must have a minimum pull-out
rating of 1,000 pounds.
IMPORTANT
Read this entire installation manual to ensure proper installation. When finished with the installation, file this
manual with the owner or maintenance department. Compliance and conformity to local codes and ordinances
is the responsibility of the installer. Product warranties may be found under “Products” on our Web site at
www.bradleycorp.com.
Separate parts from packaging and make sure all parts are accounted for before discarding any packaging
material. If any parts are missing, do not begin installation until you obtain the missing parts.
For standard height mounting, do not exceed the recommended 33.5" distance from the fixture rim to the
finished floor.

Installation LVAD3
Bradley • 215-1851 Rev. A; ECN 17-08-002 4/17/2017 3
Components
LVAD3BO
Contact your Bradley
Representative for color options
Individual Rough-In Option
Chrome P-trap (S29-094)
Plastic P-trap (269-1697)
O-Ring
(125-111)
Drain
Adapter
Packing
Washer
#10-24
Screw
Drain
Adapter
Prepack
(S45-2480)
Wall Bracket
(140-1153)
Access Panel
(186-1913)
Drain Cap
(111-141)
Drain Cap Spacer
(269-2540)
Trough Strainer
(173-040)
Trough Strainer Screw
(160-353)
Access Panel Bracket
(140-1172)
#10 Access Panel
Thumb Screw
(160-536)
Access Panel Security
Screw Option
(S45-2880)
TMV Valve
(1/2" NPTM
Outlet)
(S45-2701)
Hose Prepack
(S45-2730)
Supply
Fittings
(S45-2510)
TMV Supply
Connections
Plastic Hose
Supply Fittings
(S45-2511)
Hose Prepack
(S45-2731)
Tempered Supply
Connections
Plastic
Hose
Plastic Hose
Stainless
Steel
Hose

LVAD3 Installation
44/17/2017 Bradley • 215-1851 Rev. A; ECN 17-08-002
Components
IR-DCD Faucet
(S53-336)
CAP-DCA Faucet
(S53-334)
Battery Box for
CAP-DCA Faucets
6315-KT0000 Soap Dispenser 6324-68 Soap Dispenser 6334 Soap Dispenser
Optional
Transformer
Plug-In Transformer
Option (PT) for
IR-DCD Faucet
(S53-337)
Plug-in transformer option (PT)
includes Transformer (S53-338),
Adapter (S53-339), and Grounding
Kit (S53-349) for CAP-DCA Faucets
IR-DCG Faucet
(S53-350)
Plug-In Transformer
Option (PT) for
IR-DCG Faucet
(153-486)
*Adapter included with faucet (TMV: S45-2872, TL: S45-2871) *Adapter included with faucet (TMV: S45-2872, TL: S45-2871)
**Adapter S45-2873 included with faucet

Installation LVAD3
Bradley • 215-1851 Rev. A; ECN 17-08-002 4/17/2017 5
Dimensions
Top View (shown with CAP-DCA faucet and 6315 soap)
Front View
Supplies Required
• (6) ³⁄₈" fasteners and wall anchors for bowl and wall bracket (minimum pull-out rating of 1,000 lbs.)
• (4) ¼" fasteners and wall anchors for access panel brackets (minimum pull-out rating of 100 lbs.)
• ½" hot/cold or tempered stub-out
• 1½" NPT drain stub-out(s)
• OPTIONAL: (3) 110 volt GFCI protected electrical outlets for 100–120 VAC plug-in transformers only
• Screen filter(s) as needed, if not included with faucet(s)
• Drill
• Crescent wrench
• Tape measure
6" (152mm)
(3X)
21"
(533mm)
5"
(127mm)
30"
(762mm)
1-5/8"
(40mm)
2-1/2"
(64mm)
80"
(2032mm)
89-3/4"
(2280mm)
20"
(507mm)
3-3/4"
(95mm)
86-3/4"
(2204mm)
90"
(2286mm)
• Phillips screw driver
• Flat head screw driver
• Level
30"
(762mm)
14-3/8"
(366mm)

LVAD3 Installation
64/17/2017 Bradley • 215-1851 Rev. A; ECN 17-08-002
Dimensions – Side View
A
B
14"
(357mm)
3-3/4"
(95mm)
C
20"
(508mm)
21"
(534mm)
20°
7-1/2"
(190mm)
7-1/2"
(191mm)
2"
(50mm)
ADA/TAS Standard Height
ADA/TAS Juvenile Height
(Children 6-12 years) CSA Standard Height
Dim A 33-1/2" (851mm) 30-1/2" (775mm) 33-1/2" (851mm)
Dim B 27" (686mm) 24" (610mm) 29-29/32" (760mm)
Dim C 13-1/2" (343mm) 10-1/2" (267mm) 13-1/2" (536mm)

Installation LVAD3
Bradley • 215-1851 Rev. A; ECN 17-08-002 4/17/2017 7
Mounting for Standard, ADA and TAS height shown.
Structural Rough-Ins
Points A, B and C require sufficient backing
compliant with local building codes.
WARNING Ensure bowl is completely seated in
the wall bracket and securely fastened
to the wall at point A.
(mm)
31-1/2"
(800)
AA
B
B
C
L
28-1/2"
(723)
Bottom of
Bracket
CODE DESCRIPTION QTY.
A Install (1) 3/8" wall anchor with a minimum pull-out force of 1,000 lbs. per local codes at locations shown 2
B Provide structural backing compliant with local building codes. 2
C Install wall anchor with a minimum pull-out force of 100 lbs. per local codes at locations shown 2
Wall Bracket
RIM HEIGHT VERTICAL HEIGHT ADJUSTMENTS FIXTURE STYLE
33½" No Adjustment Standard Height, ADA, TAS and CSA
30½" Subtract 3" Juvenile, ADA and TAS
C
C25-1/4"
(640)
33-1/2"
(851)
39-1/8" (993)
42-5/8" (1082) 42-5/8" (1082)
39-1/8" (993)
3/4"
(19)
36-1/2" (927)
40" (1016) 40" (1016)
3-3/4"
(96)
Secure bracket to wall using min.
(2) ³⁄₈" anchor bolts to the left of
C/L and min. (2) ³⁄₈" anchor bolts
to the right of C/L. The (2) anchor
bolts to the right of C/L must be
min. 16" apart from the anchor bolts
to the left of C/L. When mounting
is complete, check to ensure the
bracket is level. See Step 1: Bracket
Mounting for more information.

LVAD3 Installation
84/17/2017 Bradley • 215-1851 Rev. A; ECN 17-08-002
Plumbing and Electrical Rough-Ins
Mounting for Standard, ADA and TAS height shown.
(mm)
33½"
(851)
Rim
Height
18"
(457)
A
E
EE
HC
40"
(1016)
CODE DESCRIPTION QTY.
A 1½" NPT Drain, Stub-out 2" from wall 1
H,C ½" Nominal (⁵⁄₈" O.D. Comp.) Hot/Cold supplies, Stub-out 2" from wall 1
E 110V GFI protected electrical outlet 3
12"
(305)
15-1/8"
(384)
16-3/4"
(425)
2-3/4"
(70)
24-1/8"
(613)
Finished
Floor

Installation LVAD3
Bradley • 215-1851 Rev. A; ECN 17-08-002 4/17/2017 9
Bracket Mounting
Typical installation is shown. It may be necessary to repair the wall
after mounting. The fixture may not cover all of the wall modifications.
1
Mounting height per structural rough-in dimensions.
For ease of drain installation, lay the bowl on its back.
2Drain Assembly
Install wall bracket to wall
per structural rough-in
dimensions. Check to
ensure the bracket is
level. Example anchor
locations shown.
A
16"
(406mm)
min.
C
L
O-Ring
Drain
Adapter
Packing
Washer
#10-24
Screw
Assemble the remaining components as
shown and thread the four screws through
the drain adapter and into the basin inserts.
Ensure the screws compress the drain
adapter evenly onto the basin.
A

LVAD3 Installation
10 4/17/2017 Bradley • 215-1851 Rev. A; ECN 17-08-002
Bowl Mounting (to Bracket and Wall)
4
Faucet Installation
3
For ease of drain installation,
lay the bowl on its back.
Install the faucets and optional
soap valves according to the
manufacturer's instructions.
A
Position bowl above wall bracket.
Press firmly on the back of the bowl
to seat the bowl flange into the wall
bracket lip. Ensure bowl is level.
A
Secure the bowl to the wall anchors
using fasteners per the structural
rough-in requirement (supplied by
installer).
B
WARNING Ensure bowl is completely seated in
the wall bracket and securely fastened
to the wall at point A.
CAUTION Bracket is not
intended to support
the weight of bowl
for an extended
period of time. Be
sure to secure the
bowl to the wall
using appropriate
fasteners.
Positioning bowl onto bracket
may require 3 people.
Other basin models may be shown
for faucet mounting visual.