BROSA Elizabeth Narrow User manual

ASSEMBLY GUIDE
Elizabeth Narrow Bookcase
v1.0

Components
Upon unpacking your bookcase from its delivery box, you should have the
separate pieces shown below. Follow the steps on the next pages to assemble
your new bookcase.
Side panel x 1
Top panel x 1
Bottom panel x 1
Back panel x 1
Shelving x 3
Shelving x 1
Leg x 2
Leg x 2
Back panel x 1
Back support
beam x 2
Back support
beam x 1
Side panel x 1

Hardware
What you need
aa x 2
Spec:
bb x 1
Spec:
cc x 2
Spec: Ø4 x 17mm
K x 4
Spec: Ø8.4 x 17 x 1.6mm
L x 4
Spec: Ø8.4 x 2mm
M x 4
Spec: M8 x 13mm
N x 1
Spec:
O x 36
Spec: Ø3.5 x 15mm
F x 16
Spec: Ø8 x 30
G x 12
Spec:
H x 1
Spec: M4
I x 4
Spec: M8 x 12 x 30mm
J x 4
Spec: M8 x 60
D x 8
Spec: Ø8 x 8.5mm
E x 2
Spec: Ø7 x 50mm
A x 10
Spec: Ø15 x 13.5mm
B x 10
Spec: Ø7 x 44.5mm
C x 8
Spec: Ø7 x 49.5mm

Step 1 Insert a cam screw (B) into each hole on both side
panels (2 & 3) the as shown in the diagram.
B x 10
Step 2 Insert a steel dowel (C) into each corner hole on the top
panel (1) and bottom panel (4) as shown, making sure
they all sit facing the correct direction.
C x 8

Step 3 Insert a dowel (F) into each side hole on the shelf (5),
both back support beams (8) and back support beam
(7) as shown in the diagram.
F x 16
Step 4 4.1 Insert a cross dowel (I) into the hole at the top of
each leg (9 & 10) making sure it sits facing the correct
direction as shown.
4.2 Insert a threaded bolt (J) into the hole on the side
of each leg (9 & 10) screwing it tightly in place.
I x 4
J x 4
I
J
J
Step 4.1
Step 4.2

Step 5 Align a back support beam (8) to the shelf (5) and
press rmly together, making sure the dowels (F) t
into the holes.
Step 6 Align a back support beam (8) to the side panel (2) and
rmly press together, making sure all parts t into each
other. Insert a cam lock (A) as shown in the diagram.
Repeat process for the structure formed in Step 5 as
well as back support beam (7).
A x 5

Step 7 Align the side panel (3) to the structure formed in
Step 6 and rmly press together, making sure that each
part t into each other. Insert a cam lock (A) into each
hole as shown in the diagram.
A x 5

Step 8 8.1 Align the bottom panel (4) to the structure formed
in Step 7 and press rmly together, making sure that
each part t into each other. Insert a grub screw (D)
into each hole inside the structure as shown. Repeat
process for top panel (1).
8.2 Insert a bolt (E) into both holes of the top panel (1)
as shown and tighten using the allen key (H).
Step 8.1
Step 8.1
Step 8.2
D x 8
E x 2
H x 1

Step 9 Align back panel (11) to its corresponding place on the
structure and secure in place with screws (O). Repeat
for the back panel (12).
O x 36
O

Step 10 Align a leg (9 or 10) to the underside of the structure
making sure the threaded bold (J) protruding from the
leg ts into the hole in the frame. Fit a at washer (K)
to the bolt (J) followed by a lock washer (L) and a nut
(M) using the spanner (N) to tighten the nut in place.
Repeat for the remaining legs (9 & 10).
K x 4
L x 4
M x 4
N x 1
J
K
L
M
N