Ecco 6550 Owner's manual

Specications:
Size: 6550X - Permanent 6.8” dia. x 4.9” high
6550X-VM - V/Magnet 7.8” dia. x 5.6” high
6570X - Permanent 6.8” dia. x 6.7” high
6570X-VM - V/Magnet 7.8” dia. x 7.5” high
Weight: 6550X - Permanent approx. 1.2 lbs.
6550X-VM - V/Magnet approx. 2.7 lbs.
6570X - Permanent approx. 1.4 lbs.
6570X-VM - V/Magnet approx. 2.8 lbs.
Models 6550 & 6570 Strobe Beacons
6500 Series strobe beacons are designed to meet SAE J1318 Class II specications.
Available in 5” & 7” height proles, the 6500 Series feature a thread-on lens, snap-t
ashtube, and 3 bolt ange/1” pipe or magnetic mounting options. 6500 Series strobes
will function on 12-48 VDC electrical systems and offer a choice of 80FPM double ash
or 65FPM quad ash operation.
Installation and Operation Instructions
360° Strobe Beacon
Input Voltage: 12 to 48 VDC (9-56V)
Current Draw: 2.37 Amps - Peak
30.3 Watts - Maximum
Operating temperature range: -30 to +50ºC
920-6500-00 Rev. F Page 1 of 8
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to ensure
the safety of you and those you are seeking to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,
which can cause personal injury and/or severe vehicle damage, including re.
4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output performance of the
system is maximized and the controls are placed within convenient reach of the operator so that s/he can operate the system without losing
eye contact with the roadway.
5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag deployment
area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal injury or death. Refer to the
vehicle owner’s manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable mounting location
ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.
6. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people,
vehicles or other obstructions.
7. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal. Never take the right-
of-way for granted. It is your responsibility to be sure you can proceed safely before entering an intersection, driving against trafc, respond-
ing at a high rate of speed, or walking on or around trafc lanes.
8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding
warning signal devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The manufacturer as-
sumes no liability for any loss resulting from the use of this warning device.
Do not install and/or operate this safety product unless you have read and understand the safety information
contained
Failure to install or use this product according to manufacturers recommendations may result in property damage, serious injury, and/or death to
those you are seeking to protect!
!
WARNING!
Installation & Mounting:
Permanent Mounting: Select the desired location on a at surface for the
strobe beacon to be mounted. The visibility of the strobe ash and ease
of wiring access should be taken into consideration in the selection of the
mounting location. Using the base gasket as a template, mark the three
mounting hole locations (see Figure 1). Drill the holes using the correct drill
size to match the hardware. A fourth hole may be drilled for wire access as
shown in Figure 1, or the wires may be routed through the slot in the base
for external access. Connect the power wires as shown in the wiring section
(see Figure 3).
WARNING!
Maximum recommended vehicle speed for safe operation using the
Vacuum Mount model is 65 mph (104 km/h), when tted to the center of a ve-
hicle roof of steel construction. Higher speeds could cause the mount to fail,
resulting in the beacon ying off of the vehicle, which could cause damage
to other vehicles, and injury or death to the passengers. The vacuum-magnet
mount is not intended as a permanent mounting for the beacon. The vacuum-
magnet mount unit must be mounted on a at smooth magnetic surface (i.e.
no berglass, ribbed style roofs, etc.). Ensure that the magnet is kept clean.
!
Caution: When drilling into any vehicle surface, make sure the area is
free from any electrical wires, fuel lines, vehicle upholstery, etc. that could
be damaged
Wiring Instructions:
The wiring for the strobe is as shown in Figure 3 below. All wiring should be
a minimum of 18AWG. The positive line must have a 10 amp fuse. A switch
may be used to control the on/off function. Note: Power must be shut off
when changing ash modes.
Important! This unit is a safety device, and it must be
connected to its own separate, fused power point to assure its
continued operation should any other electrical
accessory fail.

Pipe Mounting: The 6500 series base comes with 1” NPT threads for
pipe mounting.
Temporary Mounting, Vacuum-Magnet Mount: The Vacuum-Magnet Mount
feature includes a suction cup on the bottom of the beacon, with a magnet inside
of the suction cup, for a secure, temporary mount. The beacon should be placed
in the center of the roof where the least amount of curvature occurs. Before
installing, make sure the mounting surface is clean and there is no debris on the
bottom of the beacon or on the roof of the vehicle, which could reduce the holding
power of the suction cup and magnet. Place and remove the beacon without
sliding to avoid scratching the paint on the vehicle. After placement, the beacon
should adhere rmly to the surface. If the unit slides or moves easily, a proper
installation has not been obtained. To release the vacuum, lift the tab to release
the airlock (see Figure 2). To protect the Vacuum-Magnet Mount assembly, return
beacon to the box when not in use. Do not attempt to attach the beacon to an
ice-covered surface.
EXTERIOR MOUNTING
HOLE LOCATION
IF DESIRED DRILL
HOLE IN CENTER FOR
WIRE ACCESS
UNDERNEATH BEACON
BASE GASKET
MOUNTING
SURFACE
INTERIOR MOUNTING
HOLE LOCATION
3/4”
1/4”
Figure 1
FUSE (10 AMP)
(USER SUPPLIED)
GROUND
GROUND
SWITCH
(USER SUPPLIED)
WHITE
N/C = DOUBLE FLASH
GROUNDED = QUAD FLASH
RED
BLACK
Maintenance & Troubleshooting:
Most strobe failures can be traced to wiring or battery problems. Check all
wiring and connections to insure the correct voltage is reaching the strobe
light. If the strobe operates erratically or stops completely, and the wiring
is not at fault, the ashtube is probably worn. To replace it, remove the
lens, and remove the ashtube by squeezing on the tabs on the side of the
tube holder and pulling off. WARNING! The strobe power supply is a high
voltage device. Wait 5 minutes after turning off power before removing lens
for access to internal parts. Plug in the new tube assembly. See Figure 4.
Note: The connector is keyed to ensure proper orientation. Do not force. If
trouble continues, return product to your local dealer for warranty replace-
ment, or call ECCO Customer Service for assistance [phone].
Figure 3
Figure 4
Replacement Parts & Accessories:
PULL/ROLL TAB
UPWARD TO RELEASE
VACUUM
Figure 2
Description Part Number
Flash Tube R6501FT
Lens, 4” (replacement for 6550) R6050LX*
Lens, 6” (replacement for 6570) R6070LX*
Magnet Mount Kit A6600MK
Self Leveling Bracket A6600SLB
Branch Guard (for use with 6550) A6050BG
Branch Guard (for use with 6570) A6070BG
Dust Cover (for use with 6550) A6050DC
Dust Cover (for use with 6570) A6070DC
Vibration Dampening Kit A6600VDK
Black Top A6600BT
*where (X) indicates color: A = Amber, B = Blue, C = Clear, G = Green, R = Red
NOTE: Operating the vehicle without the outer lens installed on the product may result in damage that will NOT be covered under
warranty.
!
Learn more about emergency and warning lighting on our website.