Gima 29600 Parts list manual

COLPOSCOPIO COLPY
COLPY COLPOSCOPE
MANUALE D’USO E MANUTENZIONE
USE AND MAINTENANCE BOOK
BBG
Rev. 03.11.13

Colpy Cod. 29600 Pagina 10 di 16
Contents
I. Safety notes
pag. 11
II. Description
pag. 12
III. Assembly
pag. 13
IV. Using
pag. 14
V. Maintenance-Care
pag. 14
VI. Electrical parts
pag. 15
VII. Specifications
pag. 15
VIII. Optionals
pag. 16

Colpy Cod. 29600 Pagina 11 di 16
I. Safety notes
Within this user manual are used these two symbols:
Information about hazards causing death, heavy
physical injuries and psycological deseases or heavy
material damage.
Information about hazards causing low physical injuries
and psycological deseases or material damage.
___________________________________________
Make absolutely sure that the instrument is operated at the main voltage
indicated on the type plate at the bottom of the light source unit!
Always disconnect power plug before pulling out the lamp holder or
opening the light source!
Repairs not described in this document must be carried out only by
qualified workshops!
This instrument has not been approved for operation in areas subject to
explosion hazards!
Before power on the instrument, check if the electrical system is earthed!
The manufacturer is not liable for any damage caused by the non-compliance with the
above hints!
This instrument was designed and build according to the following rules and
standards:
-CE 93/42 D.L. n° 46 del 24/02/97.
-CEI EN 60601-1
-CEI EN 60601-1-2

Colpy Cod. 29600 Pagina 12 di 16
II. Description
12. Optical body
13. Diopter compensation
14. Green filter
15. Oculars
16. Focusing knob
17. Tilt tension adjustment knob
18. Pan tension adjustment knob
19. Height adjustment knob
20. Power unit
21. Stand
22. Base
fig. 1
10
11
9
8
7
6
5
4
3
21

Colpy Cod. 29600 Pagina 13 di 16
III. Assembly
Before loosening the knob (8) (Fig. 1)
assemble the optic head and the stand (see point 3).
4 Insert the stand (2) (fig.2) on the base (1) fixing
it with the screw (3) (use the wrench standard
supplied)
5 Assemble the optical body (4) to the stand
screwing in the small grip handle (5)
6 Connect the plug (8) in the socket (9).
Verify that the mains voltage is the
same prescribed in the specifications.
7 Connect the power cable (6) to the power unit
(7) and therefore to the mains supply.
fig. 2
6
3
5
4
3
2
1

Colpy Cod. 29600 Pagina 14 di 16
IV. Using
7. By (8) knob fig.1, set the wished vision height.
8. Regulate the pan-tilt resistance with the (6-7) knobs, fig. 1.
9. Turn “ON” the power unit (10) fig. 2 .
10. Using a plane surface object to observe, set the colposcope at an approximate focus position.
Find the best focus image with focusing knob (5) fig.1.
11. Set the correct interpupillary distance removing or approaching the eyepieces with both the
hands until the two images overlap in one circle.
12. Diopter compensation: focus on the object looking through the left eyepiece. Looking through
the right eyepiece focusig the object turning the diopter compensation ring (2) fig.1.
V. Maintenance –Care
Fuses replacing
Pull out the power cord from the power unit and open the fuses
shell as shown in (1) fig.3
Warning: Use only fuses compling with the
original. See Specifications.
fig.3
Care
- The quality of the image depends mostly on the cleanliness of the eyepieces and of the front
protection filter. To remove dirty from these, use a soft paintbrush. For persistent spots it is advise
to use a wed of cotton wool soaked in alcool.
The mechanical parts can be cleaned with up with a soft paint-brush. Keep the colposcope far from
corrosive substances.
Always keep the colposcope covered with its dust cover when not in use.
The quality of the materials employs in the construction will guarantee the best performances for
several years. If Your instrument have not to work correctly, don’t hesitate to contact Your
CENTREL agent.

Colpy Cod. 29600 Pagina 15 di 16
VI. Electrical parts
VII. Specifications
Eyepieces
10x
15x
Magnification
6,2
9,3
Field of view
35mm
24mm
Working distance
280mm
Interpupillary distance
48 –77 mm
Diopter compensation
±5 on right eyepieces
Height of vision
73 –104 cm
Fine focus
36 mm
Filter
Green
Lighting device
Power LED 4000°K
Fuses (two)
T200mA
Classification
I type B
Complains with
IEC-601-1 93/42 CEE
Main supply
90-240Vac, 50/60Hz
Weight
5 kg
Mark
Specifications could be changed without notice
E02-04 = Mains cable 230Vac
E03-06 = Green bipolar switch
E08-01 = IEC plug; snap-in 250V, 10A
E03-07 = Fuse T200mA
EL01-15 = Connector; Amphenol 4p M
EL01-16 = " Amphenol 4p F
EC01-26 = Medical switching power supply 5V; 1A
EL01-16
EL01-15
E03-07 E03-06
E08-01
E02-04
Power LED
EC01-26

Colpy Cod. 29600 Pagina 16 di 16
VIII. Optionals
CODE
DESCRIPTION
313114
MC1 analogue camera to fit directly on one eyepiece.
317014
Monitor 19” Wide, white, HDMI and video PAL input,
513202
Video cable BNC-RCA, 3m.
313103
DL1 USB digital camera 1.3Mpx, to fit on eyepiece
513015
Eyepieces (two) WF 15X.
513102
Adapter to fit a “C” mount camera on eyepiece
Centrel S.r.l. Viale Europa 18, 35020 Ponte San Nicolò PD - Italy