JSI Moto User manual

Installation Instructions
Package Contents
Page 1 of 4Moto
Linking Tables
#3 Phillips Screw Driver
Scissors
Recommended Tools
Utility Knife
(4) Washers
(4) Bolts
Rectangular 30°Wedge 22 1/2°Wedge Quarter Round
Marker
Moto seating units have factory installed T-Nuts located on both sides of the frame which are used to attach linking tables. These
T-Nuts are concealed when the chair is upholstered. After you determine which side of the chairs get the linking table, you will need to
locate the hidden T-Nuts by feeling through the upholstery with your fingers. The following installation instructions will show a rectangu-
lar linking table being attached between a Right and Left chair.
Moto linking tables are available in four different shapes. Your package will contain one of the linking tables below. The illustrations
in these instructions show using the rectangular linking table, however all table shapes use the same method of attachment. Please
adjust accordingly.
Right Chair Left Chair
Step 1
Determine which Side of the Chairs
the Linking Table will be Attached
Linking Table will go on
inside of Right and Left
Seating Units
T-Nuts beneath
upohlstery
Rectangular
Linking Table
Notice To Installers: Failure to comply with installation instructions will compromise the safety, durability and performance of this product, which may risk injury to the user of this
product and/or diminish the product life cycle. Jasper Group assumes no liability in these instances.
jsifurniture.com
800.457.4511
812.482.3204 O
812.482.1548 F
225 Clay Street / PO Box 231
Jasper, Indiana 47546
Form No. INST-MT005
5/1/16

Installation Instructions
Page 2 of 4Moto
Linking Tables
(continued)
Step 2
Locate T-Nut Fasteners beneath Upholstery
• Carefully flip chair on it’s back.
• Use fingers to locate two T-Nuts holes beneath upholstery.
These T-Nuts will be used to attach the linking table.
9”
8”
T-Nut
T-Nut
Step 3
Cut Holes in Fabric to Expose T-Nut Fasteners
• Use utility knife to cut slit into fabric in the center of T-Nut holes.
• Use scissors to cut away fabric around hole to fully expose T-Nut fasteners.
DO NOT USE THESE HOLES
Press finger firmly
against upholstery
to locate T-Nut Holes.
The holes with T-Nuts
are closest to the
seat cushion.
Cut fabric away from
holes to fully expose
T-Nuts. Make sure
holes are free from
fabric threads.
DO NOT CUT
INTO THESE
HOLES
DO NOT CUT INTO THESE HOLES
Use sharp
knife to cut
slit in center
of T-Nut holes.
Mark center
of hole.
Right Chair
Notice To Installers: Failure to comply with installation instructions will compromise the safety, durability and performance of this product, which may risk injury to the user of this
product and/or diminish the product life cycle. Jasper Group assumes no liability in these instances.
jsifurniture.com
800.457.4511
812.482.3204 O
812.482.1548 F
225 Clay Street / PO Box 231
Jasper, Indiana 47546
Form No. INST-MT005
5/1/16

Installation Instructions
Page 3 of 4Moto
Linking Tables
(continued)
Step 5
Attach Linking Table to Chairs
• Use washers and ???? screws to attach
Linking Tables to Chairs.
• The illustration below shows the linking table being attached
to the Right Chair. Repeat Step for the Left Chair.
Step 4
Repeat Steps 1, 2, and 3 for Remaining Chair
• Determine which side of chair linking table will be attached.
• Carefully flip chair on it’s back.
• Locate T-Nuts holes beneath upholstery and cut fabric away
to fully expose T-Nuts.
Left Chair
Cut fabric away
from holes to
fully expose
T-Nuts.
Make sure
holes are
free from
fabric threads.
Right Chair
Washer
???
Notice To Installers: Failure to comply with installation instructions will compromise the safety, durability and performance of this product, which may risk injury to the user of this
product and/or diminish the product life cycle. Jasper Group assumes no liability in these instances.
jsifurniture.com
800.457.4511
812.482.3204 O
812.482.1548 F
225 Clay Street / PO Box 231
Jasper, Indiana 47546
Form No. INST-MT005
5/1/16

Installation Instructions
Page 4 of 4Moto
Linking Tables
(continued)
Step 6
Flip Chairs Upright
• Carefully flip chairs upright and move to desired location.
Notice To Installers: Failure to comply with installation instructions will compromise the safety, durability and performance of this product, which may risk injury to the user of this
product and/or diminish the product life cycle. Jasper Group assumes no liability in these instances.
jsifurniture.com
800.457.4511
812.482.3204 O
812.482.1548 F
225 Clay Street / PO Box 231
Jasper, Indiana 47546
Form No. INST-MT005
5/1/16