JSI Vision-ADJUSTABLE HEIGHT DESK WITH RETURN Configuration guide

8/26/2022 Form No. INST-VS0013 1
Vision-ADJUSTABLE HEIGHT DESK WITH RETURN
Install Instrucons
(2) TOP STIFFNERS
BOX/BOX/FILE PEDESTAL
ADJUSTABLE HEIGHT
MODESTY PANEL
RETURN PEDESTAL
(6) U-BRACKETS
RETURN TOP
DESK TOP
MODESTY PANEL
Tools Required
• 5MM Allen Wrench
• Tape Measure
• Screw Driver
• Level (Minimum 4’ )
Hardware Included
• (12) #8 x 3/4 Pan Phillips
• (11) Cams and Post
• (24) #10 X 7/8 Pan Head Phillips
• (3) Flat Bracket 13 GA X 2” X 5”
• (24) #8 X 3/4 Pan Head Philips
• 40” Wire manager (Protum)
• Hardware Bag
• (6) U-Brackets
Installaon
Right Unit shown Le opposite
Figure B
Figure A

8/26/2022 Form No. INST-VS0013 2
Installaon (Modesty Panel)
Insert cams into back panel (6) places. (Figure C)
(6) CAM POST
MODESTY PANEL
Figure C
Figure D
(3) FLAT BRACKETS
(4) #8 X 3/4" PAN HEAD SCREW
DESK TOP
(BOTTOM SIDE)
RETURN TOP
(BOTTOM SIDE)
NOTE: BORING TO OUTSIDE
PROFILE EDGE
RIGHT TOP ASSEMBLY SHOWN. LEFT OPPOSITE
FILLER PANEL TOP
ASSIST
WILL BE REMOVED AFTER
TOP IS LOCATED ON UNIT
Installaon (Top and Return Top)
Determine right or le top per unit set up. Aach (3) Flat Brackets to underneath side of top using #8 x 3/4 PHP screws. Note holes to outside of
return top.

8/26/2022 Form No. INST-VS0013 3
Unit Top Installaon
Set unit up per order. Drawer pedestal on one side and Return pedestal on opposite side. Slide the (2) top stretcher bar in place, do not lock in
place. Remove the drawers from the Drawer pedestal noce where each drawer is located . Align the Return pedestal and Drawer pedestal with
Modesty panel, lock cam and post (turn Clockwise) (6) places. Using a level to level Return pedestal, Drawer pedestal and Modesty Panel. Level-
er located on boom of pedestals. Re-insert drawers.
(6) CAM AND POST
ALIGNMENT
(2) TOP STIFFNERS
LEVELER
LEVELER
(4) CORNER
LEVELER
LEVELER
Figure (E)
Unit Layout Installaon
Set top into place. Top ller assist panel will bu up to the Modesty panel inside face. Align return pedestal along side with top, should be 1/16”
top overhang. Secure (6) U-Brackets with #10 X 7/8 PHP screws (2) per bracket.
Note: There will be a 1” inset on wing end edge for pinch point relief.
Figure (F)
FILLER PANEL TOP ASSIST
FLUSH TO MODESTY PANEL
#10 X 7/8" PAN HEAD PHILIPS
(2) PER U-BRACKET (12 TOTAL)
(6) U-BRACKETS
(2) PER LEG ASSEMBLY
END PANEL REMOVED
FOR CLARITY
1" INSET FOR PINCH
POINT RELIEF

8/26/2022 Form No. INST-VS0013 4
Installaon (Cabinet and Top)
Aach electrical components to each leg, check length of cords, longest core to run from Return side. Connect power cord, leg electrical, and
control switch to Control box. Secure Control box between top support rails. Plug in power cord to source. Must re-set power box by holding
down both the up and down buon at the same me ll top lowers and re-sets. Raise top to allow access to underneath side of top. Aach top
leg bracket to top with #10 x 7/8 PHP screws, (4) per leg assembly. Remove Top assist ller. (cam and post counter clockwise) With top in fully
upright posion place Adjustable Height Modesty Panel in opening between pedestal and the xed Modesty Panel. Secure panel with cam and
post fasteners.. (turn clockwise) Secure all electrical wires with the wire clips that are provide in clean and uncluered appearance. Wire manag-
er can be posion on either pedestal, to be located vercally above hole cutout on Drawer pedestal or Return opening. Secure both ends.
Note: User discreon to where up/down switch is located. (not over Drawer pedestal or return end panel)
Figure (G)
(4) #10 X 7/8 PAN HEAD PHILIPS
(12) TOTAL
LOCATE CONTROL BOX BETWEEN RAILS
ADJUSTABLE HEIGHT MODESTY PANEL
ALLEN HEAD SET SCREW
(4) PER TOP SUPPORT RAIL