JSI Vision-Desk ADJUSTABLE HEIGHT Configuration guide

8/26/2022 Form No. INST-VS0029 1
Vision– Desk ADJUSTABLE HEIGHT
Install Instrucons
Tools Required
• 5MM Allen Wrench
• Tape Measure
• Screw Driver
• Level (Minimum 4’ )
Hardware Included
• (6) Min-x Cams and Post
• (16) #10 X 7/8 Pan Head Phillips
• (6) #8 X 5/8 Pan Head Philips
• 40” Wire manager (Protum)
• Hardware Bag
• (4) U-Brackets
Installaon
Figure B
Figure A
DESK TOP
ADJUSTABLE HEIGHT PEDESTAL
BENCH HEIGHT OPEN STORAGE
MODESTY PANEL
(2) TOP STIFFENERS
RIGHT DESK UNIT SHOWN LEFT OPPOSITE
RIGHT UNIT SHOWN LEFT IS OPPOSITE
(NOTE: 18" DEEP UNITS HAVE NO SHELF)

8/26/2022 Form No. INST-VS0029 2
Installaon (Door Panel Removable)
Remove outer panel by pulling out. Remove inner panel by sliding panel upward.
Figure C
Figure D
Installaon (Pedestal Aach to Top)
Place Top face down on a scratch resistance surface. Place Pedestal on one side of top . Secure Pedestal to Top using #8 X 3/4 Pan Head Phillips
screws to the 90° Bracket and Corner Bracket. (2 places) Secure Leg Plate Bracket and U-Bracket (2) to Top using #10 X 7/8 Pan Head Phillips.
Slide (2) Top Support Rails into Leg assembly.
OUTSIDE PANEL PULLS/SNAPS OFF
INSIDE PANEL SLIDES UP TO REMOVE
KEKU FASTENER
(2) PER PANEL
(PULL TO RELEASE)
MINI RAFIX FASTENER
(2) PER PANEL
(PULL TO RELEASE)
KEKU SLIDER FASTENER
(4) PER PANEL
(SLIDE UP TO RELEASE)
#8 X 3/4 PAN HEAD PHILIPS
(2) PER BRACKET
#10 X 7/8 PAN HEAD PHILIPS
(4) PER LEG ASSEMBLY BRACKET
(2) PER U-BRACKET (2) U-BRACKETS
(2) TOP SUPPORT RAILS
DESK TOP

8/26/2022 Form No. INST-VS0029 3
Installaon Desk Assembly
Posion Bench Height Pedestal in place. Slide Top assembly into place , insuring Top Support Rail slide into the Bench Height Leg assembly.
Secure Pedestal to to using #10 X 7/8 Pan Head Phillips screws. Lock both sides of Top Support Rails into place using 5mm Allen Wrench.
#10 X 7/8 PAN HEAD PHILIPS
(4) LEG ASSEMBLY
(2) PER U-BRACKETS (2) U-BRACKETS
ALLEN HEAD SET SCREW
(4) PER TOP SUPPORT RAIL
Figure (E)
Installaon (Cabinet)
Aach electrical components to each leg. Connect power cord, leg electrical, and control switch to Control box. Secure Control box between top
support rails. Plug in power cord to source. Must re-set Control box by holding down both the up and down buon at the same me ll top low-
ers and re-sets. Raise top to allow access to underneath side of top. Secure all electrical wires with the wire clips that are provide in clean and
uncluered appearance. Reaached Inner Panel (slide down). Reaach Outer Panel (snap in). Wire manager can be posion on either pedestal,
to be located vercally above cutout on Pedestals and inside Leg Assembly. Secure both ends.
Note: User discreon to where up/down switch is located.
Figure (F)
CONTROL BOX LOCATED BETWEEN
TOP SUPPORT RAILS
OUTER PANEL SNAPS ON
INNER PANEL SLIDES DOWN

8/26/2022 Form No. INST-VS0029 4
Installaon (Modesty Panel)
Install Mini-x Cam into Modesty panel with arrow facing to the top edge. Insert Mini-Fix post into Top, using (Table 1-1) to locate post. Turn
Mini-Fix cam clockwisw to secure Modesty Panel.
Figure (G)
MINI-FIX POST
(QTY SEE CHART)
MINI-FIX
(ARROW TO TOP EDGE)
HOLE SPACING
RIGHT UNIT SHOWN LEFT IS OPPOSITE
(NOTE: 18" DEEP UNITS HAVE NO SHELF)