MacDon M155 User manual

Break-In InspecƟons
Hours Item Check
1 Drive wheel nuts
Torque: 510 Nm
(375 lbf·) dry. Refer to
operator’s manual
5
A/C belt Tension
Caster wheel nuts Torque: 163 Nm
(120 lbf·)
Caster wheel
an-shimmy
Dampener bolts
Torque inboard bolt:
135 Nm (100 lbf·)
Torque outboard bolt:
115 Nm (85 lbf·)
Walking beam width
Adjustment bolts
Torque: 448 Nm
(330 lbf·)
10
Walking beam width
Adjustment bolts
Torque: 448 Nm
(330 lbf·)
Neutral Adjusted by Dealer
50
Hose clamps: air in-
take, radiator, heater,
and hydraulic
Hand-ghten unless
otherwise noted
Walking beam bolts Torque: 448 Nm
(330 lbf·)
Caster wheel
an-shimmy
Dampener bolts
Torque inboard bolt:
135 Nm (100 lbf·)
Torque outboard bolt:
115 Nm (85 lbf·)
Main engine
gearbox oil
Change
Drive wheel oil
lubricant
Hydraulic oil filters
(except li)
Time Service
Every
10 hours or
daily
1. Check re inflaon.
2. Check engine oil and coolant levels.
3. Clean radiator, hydraulic oil cooler,
charge air cooler, and A/C condenser.
4. Check hydraulic oil level, and inspect
hoses/lines for leaks.
5. Drain fuel filter water trap.
6. Fill fuel tank.
Every
50 hours
1. Grease caster pivots and spindle
bearings.
2. Grease top lilink pivots.
3. Clean cab fresh air intake filter.
4. Check engine gearbox/drive wheel
lubricant.
Every 100
hours or
annually
1. Clean cab air return filter.
NOTE: Refer to M155 Operator’s Manual for
complete maintenance schedule
Ongoing Maintenance Intervals
A Series, R/R1 Series, or D/D1 Series -
without Hydraulic Deck ShiŌ
DECK SHIFT/FLOAT PRESET switch allows for auto-
memory of three different float cylinder posions. For
example:
#1 - Border Width LH 5.0, RH 6.5
#2 - Normal Width LH 5.0, RH 5.0
#3 - Rocky Width LH 6.5, RH 6.5
D/D1 Series with Hydraulic Deck ShiŌ
DECK SHIFT switch acvates hydraulic deck
shiing when the header is engaged, and allows for
auto-memory of float cylinder adjustments in each
delivery opening posion.
Allows for compensaon of weight shis to the float
springs.
Float Presets
1. Switch main baery disconnect switch to ON.
2. Place GSL in N-DETENT. Push HEADER DRIVE switch to OFF.
3. Ensure seat is locked in either cab-forward or engine-forward posion.
4. Fasten seat belt. Set throle to START posion - fully back.
5. Sound horn three mes.
6. Turn ignion key to RUN posion. Single loud tone sounds. Engine
warning lights flash in self-test mode, and CDM displays
HDR DISENGAGED and IN N-DETENT.
7. Turn ignion key to START posion unl engine starts. Release key.
Allow engine to run at IDLE unl temperature reaches 40°C (100°F).
CDM displays programmed header data for five seconds (if aached) and
then returns to previous display.
NORMAL START - Engine Temp above 16°C (60°F)
Tire Pressures (10-Bolt)
18.4-26 Bar 317 kPa (46 psi)
600 65 R28 Bar 241 kPa (35 psi)
18.4-26 Turf 317 kPa (46 psi)
23.1-26 Turf 234 kPa (34 psi)
All rear re pressures: 69 kPa (10 psi)
Fluids and Lubricants
Fluid LocaƟon Capacity SpecificaƟon DescripƟon
Diesel
fuel Fuel tank
378 L
(97 US
gal)
Diesel grade
no .2
Or
Sulphur (by weight)
0.5% maximum
water and sediment
(by vol) 0.05% max.
Lubricity 520 microns
Mix of diesel
no.1 and no. 2
Sulphur (by weight)
0.5% preferred 1%
max. water and
sediment (by weight)
0.1% max. Lubricity
460 microns
An-
freeze
Engine
cooling
system
27.5 L
(7.3 US
gal)
ASTM D-6210
and
Fleetguard ES
Compleat®
Use with equal parts
water, high quality
so, deionized, or
dislled water
Grease As
required - - -
SAE mul-
purpose high
temperature
extreme
pressure EP2
1% maximum
Molybdenum
Disulphide (NLGI
Grade 2)
lithium base
Engine
oil
Engine
crank-
case
11 L
(11.6 US
quarts)
SAE 15W40
for API class SJ
and CH-4
Refer to operator’s
manual
Hydraulic
oil
Hydraulic
reservoir
65 L
(17.2 US
gal)
SAE 15W-40
compliant
with SAE
specs for API
class SJ and
CH-4
engine oil
Use as required
unless otherwise
noted
Gear
lubricant
Engine
gearbox
2.1 L
(2.2 US
quarts)
SAE 80W-140,
API service
class GL-5
Wheel
drive
1.4 L
(1.5 US
quarts)
SAE 75W-90
API service
class GL-5
A/C
refriger-
ant
A/C
system
2.27 kg
(5 lb.) R134A - - -
A/C
refriger-
ant oil
A/C
system
total cap.
240 cc
(8.1 fluid
ounce)
PAG SP-15 - - -
Fully synthec gear
lubricant, SAE J2360
is preferred

CDM Programming Mode: Windrower Setup
(See M155 Operator’s Manual for complete instrucƟons and detailed informaƟon)
SET KNIFE SPEED 
SPM
Adjusts knife speed on draper and auger headers.
Every header size and type of knife drive will have a different range for the knife speed.
Refer your header quick card for opmal sengs.
KNIFE / DISC OVERLOAD SPD 
SPM/RPM KNIFE OVERLOAD SPEED (Auger / Draper) to be set at 75% of desired knife speed.
DISC OVERLOAD SPEED (Rotary) should be set to 1300 rpm.
OVERLOAD PRESSURE 
PSI/BAR
Adjusts warning pressure of overload sensor (reel/draper/knife/disc system).
See Header Hydraulic Pressures table below.
HEADER INDEX MODE 
Reel+Drapers OR Reel Only
Auger and draper headers only.
Allows the reel and conveyor to be driven by reference to ground speed.
RETURN TO CUT MODE 
Height+Tilt OR Height Only Set funcons to be controlled by RETURN TO CUT (RTC) mode.
AUTO RAISE Sets header-up height in RETURN TO CUT (RTC) mode. Range is 4.0 (min) to 10.0 (max).
DWA INSTALLED 
NO/YES? Acvates electrical controls for Double Windrow Aachment when installed.
SWAP DWA CONTROLS 
NO/YES?
If YES is selected, the REEL FORE-AFT buons on the GSL and the DWA RAISE/LOWER switches on the
console will swap funcons.
DWA AUTO UP/DOWN 
NO/YES? Enables the express UP and DOWN features in RETURN TO CUT (RTC) mode.
HAY CONDITIONER 
NO/YES? Draper header only. Acvates hydraulics for condioner and feed deck drive systems.
AUGER HDR REEL SPD 
RPM or MPH/KMH
Selecon will appear only with an auger header aached.
Allows REEL SPEED to display in rpm or mph or kph.
SET TIRE SIZE Select installed re size for ground speed and acre counter calibraon.
SET ENGINE ISC RPM 
NO/YES? ENGINE INTERMEDIATE SPEED CONTROL. Engine rpm can be limited to a specified value while header
is engaged. Scroll to desired rpm value. Use HAZARD key to set.
SET CONTROL LOCKS 
NO/YES? Allows header funcons to be locked from Operator control
(for example: Locking reel speed and/or reel fore-acontrols from Operator.)
VIEW CONTROL LOCKS 
NO/YES?
Allows Operator to view control lock status, and engine hours when status was established
(for example: REEL FORE-AFT - 224.5 HRS LOCKED).
HEADER CUT WIDTH 
##.# FT/M
Set cut width according to operang width. Calibraon of acre counter.
Header ID displayed on CDM at top right.
SWATH COMPR INSTALL
NO/YES? Acvates electrical controls for swath compressor when installed.
Tips and Shortcuts
Enter programming
mode
Ignion ON. Press and hold PROGRAM and
SELECT at the same me unl the CDM dis-
play enters programming mode.
Exit programming
mode Press PROGRAM.
Change language to
English
Ignion OFF. Press and hold HEADER INDEX
and PROGRAM and SELECT.
Clear sub-acres
Cab-Forward posion. Ignion ON.
Press SELECT unl SUB-ACRES is viewed on
the boom line of the display.
Press and hold PROGRAM unl SUB-ACRES
changes to 0.0.
DisconnecƟng
baƩeries
The BATTERY DISCONNECT switch is located
behind the baeries, and can be accessed by
opening the maintenance plaorm. Ensure
the switch is in the OFF posion when servic-
ing electrical components, and when the
windrower will not be used for longer than
one week.
Header Model ApplicaƟon/System Suggested Overload Warning
Seƫng kPa (psi)
Windrower Pressure Relief
Seƫng kPa (psi)
R/R1 Series Disc pressure 27,579 (4000) 28,958 (4200)
A Series
D/D1 Series
Reel / draper pressure 20,684 (3000) 22,063 (3200)
Knife / condioner pressure 27,579 (4000) 28,958 (4200)
Header Hydraulic Pressures
Enhanced reel/conveyor speed controls may be desirable
in variable crop and terrain condions.
Allows the reel and conveyor to be driven by reference to
ground speed, so that header systems speed up and slow
down as ground speed changes.
OperaƟon of Header Index for REEL SPEED:
(A Series and D/D1 Series)
1. With all bystanders clear, start windrower, and engage
the header.
2. While staonary, with the GSL in N-DETENT, use the
REEL SPEED control switch to set a minimum reel
speed.
3. When operang at grounds speeds faster than the
minimum reel speed + header index value, REEL
SPEED display will change to REEL INDEX. Using the
REEL SPEED switch on the GSL, header index can be
adjusted.
4. Reel speed will be equal to the greater of the sum of
Ground Speed + Index Value, OR Minimum Reel Speed.
OperaƟon of Header Index for DRAPER SPEED:
(D/D1 Series Only)
Follow instrucons above, using the CDM AUGER/DRAPER
speed control, rather than the GSL REEL SPEED switch.
Header Index Mode