Nautilus Hyosung Ocean ATM NH2600SE User manual

1038 Route 88, Suite 2
Point Pleasant, NJ 08742
Phone [phone]
Fax [phone]
www.OceanATM.com
NH2600SE Quick Reference Guide
1 ATM Power On/Off
ATM Power On
Open the upper front door.
Press Power Switch in the direction of “I”.
ATM Power Off
Press Power Switch in the direction of “O”.
2 Security Door Open
Security Door Open
2 Turn the key clockwise to open the security cover.
The default password of electronic lock is 1-2-3-4-5-6.
Enter this sequence on the electronic lock keypad. (①).
1 The lock will confirm a valid combination entry with a
double signal. Lock will signal three (3) times for invalid
combination entry.
Turn the vault door handle counterclockwise. (②)
The vault door will open.
3 Opening the Exterior Door
Opening the upper front body door,
- Insert the key and turn it clockwise. (①)
- Pull the front panel outward. (②)
Opening the lower front body door,
- Open the security cover with key. (③)
- Unlock the e-lock and open security door. (④)
3-1 3-2
3 4
4 Cash Replenishment
Enter to Supervisor mode (Refer to
“9 OP Main Screen”)
Select “SETTLEMENT”
Submit “TRIAL CASSETTE TOTAL” to
show note count.
* To show note count and to clear note
count, submit “CASSETTE TOTAL”
How to add note count,
Open the security door. (Refer to “3 Opening the
Exterior Door”)
Pull out the cash cassette carefully.
Unlock the cassette cover using key (①).
Pull the push plate back until it is locked
against the push plate latch. (②) And then,
set the bills into the cash cassette.
Then, release the push plate from the cash
plate latch and allow it gradually to take up
its position behind the notes. (③)
4-1 - Select “SETTLEMENT”
- Select “ADD CASH”
- Select the cassette to be added the
notes(①)
- Enter the note count and then press
ENTER key in PIN Pad. (If you want to add
the cash for other cassette, repeat from “①”)
- After completing, press “APPLY” button.
4-2 Close the cassette cover with key, place
it carefully on the set guide and push it in
until it is locked in place.
1
2
3
* The above description is based on 1000 new note
capacity cassette. For 2000 new note capacity
cassette, refer to operator manual.
1
2
Caution: The acceptable condition bills should be
loaded (Refer to Operator Manual)

1038 Route 88, Suite 2
Point Pleasant, NJ 08742
Phone [phone]
Fax [phone]
www.OceanATM.com
3
NH2600SE Quick Reference Guide
5 Receipt Paper Replenishment
2
1
Caution: The acceptable condition papers should be
loaded (Refer to Operator Manual)
Open the upper front door with key. (Refer to
“3 Opening the Exterior Door”)
Remove the roll guide by pulling it off (①).
Add the receipt paper into the rod and then
5-1 5-2 insert the roll guide tightly again to fix it. (②).
Insert the leading edge of paper between
lower guide and upper guide of printer slowly
until paper is going to start feeding. (②)
6 Note Jam
Caution: Before removing jam, power off for your safety.
6-1
Enter to “OP Main” screen, and submit
“CLEAR” button (Refer to “8 Device Reset”)
If jam is not cleared, power off
Open the security door. (Refer to “3 Opening
the Exterior Door”)
Pull out the cash dispenser (①).
Move the belt by turning the knob beside
cash dispenser to move jammed note into
a well removed position. (②)
Remove jammed note carefully and power on.
6-2
* Be sure to check if the belt is positioned
correctly after removing the jammed bills.
2
* The above description is based on CDU with
1000 new note capacity cassette. For CDU with
2000 new note capacity cassette, refer to
operator manual.
7 Receipt Paper Jam
1 2
7-1 7-2
8 Device Reset
Open the upper front door with key. (Refer to
“3 Opening the Exterior Door”)
To remove a jam inside transport path,
press down the button to release the lower
roller assembly (①) .
To take out a jam in front of transport path,
lift up the transparent window guide. (②)
After finishing clearing the jam, load the
receipt paper properly. (③).
To reset each device with error of ATM, enter to “OP
Main” screen, and press “CLEAR” key of EPP.
9 OP Main Screen
To enter to Supervisor mode, press ENTER,
1 CLEAR, CANCEL, 1, 2 and 3 keys in order.
(Default Password: “555555” and it is changeable in
Supervisor mode.) (①)
2 If correct password is entered, “OPERATION
FUNCTION” menu will be displayed. (②)
* Pressing CLEAR key erases the entered number and
pressing CANCEL key goes to in-service-mode.
Contact Information
1