Perma PRO C LINE User manual

2
1
4
3
1
2
perma PRO C LINE
Quick Start Guide
Anschließen des Anschlusskabels
Push the PRO LC into the protection cover until
lubricant comes out of the opening
Place the PRO LC inside the protection cover and remove
the plug of the PRO LC.
INSERT BATTERY
1COVER FOR PRO LC & PLUG2
DISCHARGE OPENING
3 4
Insert the battery PRO B into the drive unit (according to
the direction of the arrow on the label).
The Expert in Lubrication Solutions
No function!
Setting of PRO LC size
is done via menu on
the display.
Battery PRO B
(Back-up battery)
Catch
Gear theeth
Protection cover for PRO LC
PRO LC
Plug
DRIVE
Assembly
Connect the four strands of the connecting cable to the control system of your equipment. Pay attention to the pin assignment of
the connector on the lubricator. Insulate the connected strands correctly. Insert the 4-pole connecting cable into the connector
of the PRO C LINE Drive. Screw tight the connector socket of the connecting cable to the connector of the PRO C LINE Drive.
Pin no. of the connector
on the lubricator Strand color of the standard cable Function
1 brown Not assigned
2 white Malfunction*
3 blue Ground
4 black Voltage (15 V to 30 V - DC)
*Error signal is low-active! (negative logic)
Scan the QR code
for a video tutorial.
Place the PRO LC with its protection cover on the drive unit.
Turn the cover clockwise until the bayonet catch locks.

perma-tec GmbH & Co. KG
Hammelburger Str. 21
97717 Euerdorf
GERMANY
Tel.: [phone] - 0
[email protected]om
www.perma-tec.com
Settings and Display
Display
MODE
SAVE Display
SELECT
Meaning / Description
Display at delivery with
attached PRO LC
MODE
SAVE
Display: Discharge time
remaining PIN-reset
Info
MODE
SAVE
Enter rst digit of current PIN
PIN “00” at delivery
PIN-Entry
MODE
SAVE
Enter second digit
of current PIN
MODE
SAVE
Set PRO LC size
LC
MODE
SAVE
Activate outlets:
Activate outlet 1 Outlets only
displayed if MP-6 is connected
Outlets
Outlet 1 activated
MODE
SAVE
Outlet 2 activated
(if desired, other outlets may be
turned On / Off the same way)
MODE
SAVE
Enter number of strokes for outlet 1
Strokes
MODE
SAVE
Pause time conguration
for outlet 1:
Changing the rst digit
Pause time
MODE
SAVE
MODE
SAVE
Pause time conguration
for outlet 1:
Changing the second digit
MODE
SAVE
PIN (rst digit) enter for initial
conguration or after a PIN-reset
– otherwise, setting is complete
PIN
MODE
SAVE
PIN (second digit) enter for initial
conguration or after a PIN-reset
MODE
SAVE
Conguration nished
INTRO
Repeat for each outlet:
Conguration of strokes and
pause time
Total discharge period
Lubrication system turned off (OFF)
Lubrication system turned on (ON)
Display shows „remaining
discharge period“
Change rst digit
SELECT
Change second digit
SELECT
SELECT
Change rst digit
Change rst digit
SELECT
SELECT
Change second digit
Change second digit
SELECT
Change from LC500 to LC250
SELECT
Outlet 1 On / Off
SELECT
Outlet 2 On / Off
SELECT
Changing the number of strokes
SELECT
Control Buttons
Press Short Short
Long > 4 sec.
until the display
content changes
completely
Long > 4 sec.
until the display
content changes
completely
Button
Function Selection in
current display
Changing of
values
Moves to new
menu and saves
selected values
Returns to original
menu without
saving changes
MODE
SAVE SELECT MODE
SAVE SELECT
short push
long push
blinking display
go to
CONFIGURATION MENU