Perma STAR CONTROL User manual

Blattformat: DIN A4
Maßstab: 1:1
2
1…
7
01/2021
07/2021
360°
Blattformat: DIN A4
Maßstab: 1:1
Blattformat: DIN A4
Maßstab: 1:1
Blattformat: DIN A4
Maßstab: 1:1
Blattformat: DIN A4
Maßstab: 1:1
Blattformat: DIN A4
Maßstab: 1:1
perma STAR CONTROL - Quick Start Guide
1. Predefi ne installation / Select lubricant, discharge period + connecting parts
Reducer
Remote mounting for lube-points with vibration,
limited mounting space, high temperature
Direct mounting
2. Prepare lube-point
Clean lube-point Remove grease fi tting Add reducer, support fl ange
and tubes (if required)
For remote mounting:
Prefi ll lube-point and any grease lines / connections
(use the same grease that is contained in the lubrication system)
For direct mounting:
Prefi ll lube-point and any connecting parts
(use the same grease that is contained in the lubrication system)
3. Activation / Installation of lubrication system
Add sealant
Pressure check: Lube-point / all connecting parts
Select a suitable lubricant
for perma STAR LC unit
→ e. g. perma Multipurpose grease SF01
Select discharge period
→ e. g. with perma SELECT APP
(refer to our product catalog for details)
Possible mounting positions:
Examples: Bearing lubrication
© 2021/10 · en · Version: 1.1
(Oil fi lled LC
+/- 45°)
Mounting bracket
STAR Standard Duty
1-point G1/4 female
(109663) Hose connector G1/4 male for
hose iØ 9.5 mm - push-lock
(101554)
Heavy Duty hose up to
+100 °C oØ 16 mm x iØ 9.5 mm
(101555)
Hose connector G1/4 male for
hose iØ 9.5 mm - push-lock
(101554)
Support fl ange STAR
G1/4 male x G1/4 female
(109420)
Assemble drive
and LC
Tighten threaded ring hand tight until
the white triangle is completely visible
Note activation /
exchange date
on label
Confi guration can be
found on the back page Remove plug
Connect the cable to the
drive by screwing it on
Remove cap and screw
the lubrication system into
the lubrication point
Support fl ange
www.perma-tec.com
Reducer

LC120
MODE
cm³/Impulse
IMPULSE
/Impulse
/Impulse
/Impulse
cm
cm
cm
/Impulse
/Impulse
/Impulse
IMPULSE
IMPULSE
IMPULSE
IMPULSE
IMPULSE
IMPULSE
IMPULSE
MODE
IMPULSE
MODE
IMPULSE
MODE
IMPULSE
IMPULSE
IMPULSE
LC120
MODE
Month
TIME
Month
Month
Month
TIME
TIME
MODE
MODE
TIME
MODE
TIME
TIME
TIME
TIME
TIME
SET
MODE ◄
TIME
MODE ►
IMPULSE
IMPULSE
IMPULSE
3
4
1
2
1 + V DC
2 OK
3 GND
4 Err
21001
4 0101
OK/ Err Err LC 2101
4 0 0 1
OK/ Err Err/LC
LC60
LC120
LC250
LC500
MODE
TIME
500
L
L
TIME
L
L
L
L
L
L
TIME
L
L
L
L
L
TIME
L
L
TIME
L
L
L
L
L
L
L
L
L
L
L
L
TIME Mode
Electrical connection Signal output Connection in parallel
IMPULSE Mode
www.perma-tec.com/star-control-parallel-wiring
HINT
Wiring diagram for 4 perma STAR CONTROL
OR
Confi guration
Electrical connection
Quick Reference
Feature Description
Power supply Power supply is indicated by the plug symbol in the display.
Purge
Access the purge feature by holding down the SET button for 10 seconds. Release
the button when “PU” appears and the purge will start automatically and show the
“PU” LCD display. The green LED will fl ash. The purge cycle runs for 3 complete
revolutions of the drive spindle to deliver around 6 cm³ of grease. It can be stopped
at any time by pushing the SET button once.
Normal operation:
- Green LEDs fl ash every 7 seconds
- LCD screen displays Time / Impulse setting & volume
Run cycle (lubricant being delivered):
- Green LED’s fl ash every second
- LCD screen displays “ru”
Empty Lubricant Cartridge (LC):
- Red LED’s double fl ash every 2 seconds
- LCD screen displays “LC”
Blockage / Back Pressure Overload (OL):
- Red LED’s double fl ash every 7 seconds
- LCD screen displays “OL”
Purge (PU):
- Green LED’s fl ash every second
- LCD screen displays “PU”
L
C120
◄
cm³
/100 h
Month
TIME
L
C1
L
C1
L
C1
L
L
L
L
L
TIME
TIME
L
L
L
L
L
L
L
◄
TIME
TIME
TIME
TIME
◄
L
C120
◄
cm³
/100 h
Month
TIME
L
C1
L
C1
L
C1
L
L
L
L
L
TIME
TIME
L
L
L
L
L
L
L
◄
TIME
TIME
TIME
TIME
◄
LED Light & LCD
Screen combinations
9-30 V OUTPUT
Set the LC size by
pressing the SET button
(60, 120, 250, 500 cm³)
Hold down SET button for 5 s; Select
desired mode („TIME“ & „IMPULSE“)
by pressing the SET button
Set the discharge period by
pressing the SET button
(1-12 months; 1-26 weeks → only 500 cm³)
Set the discharge volume per
impulse by pressing the SET button
(0,1 - 9,5 cm³)