Steelcase Brody Desk Manual

Brody Desk
Disassembly Direction
®
T20, T30, T40 TORX
4mm, 5mm, 6mm HEX
™
3mm HEX
8mm SOCKET
3" and 12"
BIT HOLDERS
©2019 Steelcase Inc.
Grand Rapids, MI 49501 U.S.A.
Printed in U.S.A.
Extension (see page 8)
Power (see page 6)
Base and Feet (see page 8)
Lighting (see page 5)
Screens (see page 2)
Worksurface (see page 7)
Page 1 of 9
139077 Rev A

®
Bins for components removed
SCRAP
SCREEN DISASSEMBLY
1. Pry top caps off and discard.
2. Remove all screws from the screen bases
(T30 TORX + 12" BIT HOLDER). Loosen middle
brackets (3mm HEX) if needed.
3. Lift the screens from the base. Set aside.
ALUMINUM
(all)
4. Remove the (2) screws (T30 TORX) from the middle
brackets and discard.
STEEL
8
7
9
T30 TORX
Page 2 of 9
139077 Rev A

®
Bins for components removed
ALUMINUM
SCREEN DISASSEMBLY (continued)
5. Remove all attaching screws (T30 TORX) from the
mounting plates and discard.
6. If screen(s) are fabric-covered, refer to Page 5. Remove
screws (T20 TORX) from the bottom of screen
uprights. Disengage the uprights from the screen hooks
and discard.
7. Discard screen(s).
7
6
5
ACRYLIC*
*see page 5 if fabric-covered
T20 TORX
T30 TORX
T30 TORX
STEEL
(all)
Page 3 of 9
139077 Rev A

®
Bins for components removed
STEEL
FABRIC-COVERED SCREEN DISASSEMBLY
8. Locate zipper on the bottom of the fabric sock. Unzip the entire
length.
9.
Remove screws (T20 TORX) from the bottom of screen
uprights. Disengage the uprights from the screen hooks
and discard.
10.
Discard screen(s).
9
10
ALUMINUM
11.
Peel fabric sock off of steel screen substrate and remove both top
corner pieces. Discard fabric and corner pieces.
FABRIC
ABS
8
9
T20 TORX
(all)
Page 4 of 9
139077 Rev A

®
Bins for components removed
SCRAP
LIGHTING DISASSEMBLY
1. Unplug light power cord.
2. Unplug power cord from light fixture.
3. Lift up to remove light fixture from base and discard.
2
4. Unscrew nut (8mm socket) from base and discard.
5. Remove base from worksurface and pull power
cord through the hole. Remove foam washer
and discard base and washer.
STEEL
345
Page 5 of 9
139077 Rev A

®
POWER MODULE DISASSEMBLY
1. Use a flathead screwdriver to remove the power module.
2. Remove the wire from wire clips.
SCRAP
Bins for components removed
1
2
Page 6 of 9
139077 Rev A

SCRAP
STEEL
®
WORKSURFACE DISASSEMBLY
1. Remove all the screws from the underside of the worksurface.
2. Remove the worksurface and discard.
Bins for components removed
1
2
Page 7 of 9
139077 Rev A
(all)

®
Bins for components removed
NYLON
STEEL WASTE
3
1
3
1
L-BRACKET
(STRAIGHT) LEG
GANGING BRACKET
L-BRACKETS
(STRAIGHT) LEGS
2
T40 TORX
T40 TORX
T40 TORX
T40 TORX
(ANGLED) LEG
T40 TORX
BASE AND EXTENSION DISASSEMBLY
1. Remove screws (T40 TORX) from legs.
2. Remove glides from legs. Discard glides. Remove
threaded inserts from legs with flat bladed screwdriver
and discard inserts and legs.
3. Remove screws (T40 TORX) from L-brackets and ganging
bracket if an extension unit is involved. Discard.
Page 8 of 9
139077 Rev A
(all)

3
®
4
1. Remove screws (T40 TORX) from ganging bracket.
GANGING BRACKET DISASSEMBLY
SCRAP
STEEL
Bins for components removed
(2x) Page 9 of 9
139077 Rev A
(all)