Steelcase Sync User manual

Sync™Single-Leg/Double-Leg Base Units
Page 1 of 7
939549945 Rev E
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2014 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
®
HEALTH
This equipment has been tested and found to comply with the limits for a class B digital device pursuant
to Part 15 for FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the
separation between the equipment and receiver. • Connect the equipment into an outlet or a circuit different
from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician
for help.
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada
The power socket/outlet shall be installed near the equipment and shall be easily accessible.
SAVE THESE INSTRUCTIONS
OPERATING INSTRUCTIONS - Please refer to the attached Installation Instructions and the provided User Guide.
USER-MAINTENANCE INSTRUCTIONS -
-
DANGER
Do not modify the plug provided with the product - if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
The receptacle power block is equipped with a circuit breaker that will shut
off power in an overload condition. Press to reset the circuit breaker to restore power.
SERVICING OF DOUBLE-INSULATED PRODUCTS - In a double-insulated product, two systems of insulation are provided
instead of grounding. No grounding means is provided on a double-insulated product, nor is a means for grounding to be added
to the product. Servicing a double-insulated product requires extreme care and knowledge of the system, and is to be done only
by qualifiedservice personnel. Replacement parts for a double-insulated product must be identical to the parts they replace. A
double-insulated product is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED.” The symbol
(square within a square) is also able to be marked on the product.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical furnishing, basic precautions should always be followed, including the following:
Read all instructions before using (this furnishing).
- To reduce the risk of electric shock:
DANGER
1. Always unplug this furnishing from the electrical outlet before cleaning.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
3. Use this table only for its intended use as described in these instructions. Do not use attachments not
recommended by the manufacturer.
4. Never operate this table if it has a damaged cord or plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water. If the cord is damaged have it replaced by a Steelcase dealer.
5. Keep the cord away from heated surfaces.
6. Never drop or insert any object into any opening.
7. Do not use outdoors.
8. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
9. To disconnect, remove plug from outlet.
10. Do not use this table to support televisions.
11. Each surface intended to support a load shall have a corresponding statement in the use instructions specifying the
maximum intended load for that surface.
12. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
13. Children should be supervised to ensure that they do not play with the appliance.
WARNING

®
WARNING
Pinch points. Keep Clear.
Risk of Serious Injury.
If not used as intended, moving
worksurfaces can pinch and
cause injury or property damage.
Always follow these instructions:
Keep height-adjustment range free from
obstructions above and below the worksurface.
Plan for a minimum 1” gap against a wall or panel.
Plan for a minimum 1” gap to adjacent furniture.
1.
2.
3.
This powered, adjustable height desk appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not play with the appliance.
WARNING
RISK OF SERIOUS INJURY:
Page 2 of 7
939549945 Rev E
2
1
3

1. For height adjustable units, measure any protrusion from back or side walls
that exists below the maximum adjusted height of worksurface.
2. Make sure resulting width of installation niche from back wall corner to
corner, after subtracting any side wall protrusions, falls within the following
ranges for the respective nominal width unit:
• 60" nominal - 54" to 66"
• 72" nominal - 66" to 78"
(Omit this step for Single Leg)
Page 3 of 7
939549945 Rev E
MARK HOLE
LOCATIONS
MARK HOLE
LOCATIONS
4
FOR 135 DEGREE WORKSURFACE LOCATIONS
[943102529SR]
FOR 90 DEGREE WORKSURFACE LOCATIONS
[943102528SR]
3. Use (customer service part number 943102528SR for 90° legs
and 943102529SR for 135° legs) template to mark three (3) hole
locations for floor anchors.
4a. Offset "side wall" edge of template from side wall by depth of
any protrusions (window frame, sill, etc.) that exist between 25" - 50"
above floor.
4b. Offset "back wall" edge of template by a distance 1" less than
depth of any protrusions (window frame, sill, etc.) that exist between
25" - 50" above floor.
WIDTH OF THE
INSTALLATION NICHE
BACK WALL
PROTRUSION
SIDE WALL
PROTRUSION
DEPTH
DEPTH MINUS 1"
SIDE WALL
PROTRUSION
DEPTH
BACK WALL
PROTRUSION
DEPTH MINUS 1"
®
HEALTH

6
FLOOR
ANCHOR
NOTE: Consult building's Engineer of Record to
specify correct fasteners for attachment to
building and to ensure that building has adequate
structure. There are three (3) holes provided per
mounting plate (.600” diameter) for floor anchor
clearance. Product was tested while mounting to
3/8” diameter floor anchors in 4” concrete.
5. Install floor anchors per fastener
manufacturer's specifications. Leave 2-1/4" of
exposed stud for leveling purposes.
6. Thread a nut, then a washer on each floor
anchor as shown.
7. Loosen nuts on the upper and lower support
rails to allow the unit to adjust to the floor anchor
position.
(Omit this step for Single Leg)
8. Set unit on floor anchors. Plumb and level
base unit using nuts and washers.
9. Plumb each leg making sure top support rail is
also level. Use nuts to make any necessary
adjustments.
10. Secure unit with a washer, lock washer and
nut, as shown, to secure plate.
11. Tighten nuts on upper and lower support rails
that were loosened in step 7.
(Omit this step for Single Leg)
12. Check legs and top support rail for plumb and
level.
Page 4 of 7
939549945 Rev E
CROSS SECTION
OF FINAL ORDER FLOOR ANCHOR
NUT
LOCK WASHER
WASHER
PLATE
NUT
WASHER
MFG. RECOMMENDED
NUT / WASHER
FLOOR ANCHOR
NUT
LOCK WASHER
WASHER
10
7
LOOSEN LOWER SUPPORT RAIL HERE
LOOSEN UPPER SUPPORT RAIL HERE
®
HEALTH

13. Install CPU's using straps provided.
14. Route all power and data cables necessary.
For adjustable height legs, reference Wire
Management assembly direction 939549946.
Page 5 of 7
939549945 Rev E
13
®
HEALTH