Steelcase Turnstone Conference Space Solution Set User manual

Conference Space - Solution Set
Page 1 of 5
939500312 Rev A
If you have purchased this product on Steelcase
Store, call 800.516.3454.
If you have purchased this product through an
authorized retailer, please contact them directly
or visit our website: www.steelcase.com
© 2008 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
R
#2 ACR BIT
3/8” OPEN
END WRENCH

Page 2 of 5
939500312 Rev A
Rectangular
Top Version
1. Flip the worksurfaces
over onto a clean,
protected surface.
2. Slide worksurfaces
together.
3. Lower two (2) tie
brackets into slots (3a)
and tighten in two (2)
places using a 3/8" open
end wrench (3b).
4. Place four (4) tie
straps onto worksurface
and secure each tie strap
using four (4) screws.
13”
APPROX.
1”
APPROX.
13”
APPROX.
1”
APPROX.
2 PLACES
2 PLACES
3a
3a
4
4
4
4
3b
3b
TIE STRAP
TIE
STRAP
TIE
BRACKET
TIE
BRACKET

Page 3 of 5
939500312 Rev A
1. Position column legs onto worksurface
as shown.
NOTE: Column legs come in two (2)
lengths: 27"H and 39"H.
2. Attach each leg to worksurface by
securing with twelve (12) screws.
3. Lower base assembly onto column leg
(3a) and secure using two (2) 3/8-16 x 1-1/4"
long hex head screws (3b).
Leg to Worksurface Locations
Rectangular, Racetrack & Boat-Shaped
Conference Table Top - 48x120
3b
3a
3/8-16 x 1-1/4" LONG
HEX HEAD SCREWS
Rectangular
Racetrack
1
1
1
2
Boat-Shaped

Page 4 of 5
939500312 Rev A
Leather Executive Chair
IMPORTANT: PAY ATTENTION TO ARM
ASSEMBLY
(STEP 2)
1. Attach seat to back
Lay the chair back on the floor. Take care
to ensure that the back will not be
scratched or cut. Align j-bar with bottom
of seat.
2. Attach arms to seat/back assembly
Align arms to chair (2a) and make sure
that the arms are positioned over the hubs
(2b). Attach the arms using four (4)
2-3/16" long pan head screws (2c).
To avoid cross threading, start all
four (4) screws by hand before
tightening, making sure that the
screws are not going in the holes on
an angle (2d).
1
Not included with
sled base chair
2c
IMPORTANT
2d
2b
BACK
ARM
2a

Page 5 of 5
939500312 Rev A
3. Locate the four (4) holes on
the chair seat (3a) and attach
using four (4) 1-1/16" long hex
head bolts. Push decorative
cover over screw heads (3b).
NOTE: After j-bar screws are
tightened. Ensure all arm screws
are still tight.
4. Insert cylinder into base
With base resting on floor, insert
cylinder as shown.
5. Assemble cylinder cover
Slide cover (A) up through cover
(B) (see fig 1). With cover (A)
engaged with cover (B), slide
cover (C) down over covers (A
and B) (see fig 2). Refer to fig. 3
for completed assembly.
6. Place cover over the
cylinder in base.
7. Attach seat assembly to
cylinder
Line up hole over cylinder, and
place seat down. Grab the seat
and firmly push the entire chair
towards the floor to properly lock
the tapers on the cylinder into the
seat and the base.
fig. 1 fig. 2 fig. 3
B
B
A
C
B
C
A
B
C
A
A
7
6
5
4
3a
3b