Steelcase Turnstone Small Office Solution Set User manual

Small Office - Solution Set
Page 1 of 5
939500310 Rev A
If you have purchased this product on Steelcase
Store, call 800.516.3454.
If you have purchased this product through an
authorized retailer, please contact them directly
or visit our website: www.steelcase.com
© 2008 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
R
#2 ACR BIT
5/16” OPEN
END WRENCH
1/4” OPEN
END WRENCH
5/16" DIA.
DRILL BIT

Page 2 of 5
939500310 Rev A
Lower Storage
Cabinets
Glide Installation
1. Turn the lower
storage cabinet to an
upside down position
on a clean, scratch
resistant surface.
2. Screw glides on all
four (4) corners of the
lower storage cabinet.
3. Turn the lower
storage cabinet to an
upright position and
level.
Mobile Pedestal
Caster Installation
1. Turn the mobile
pedestal to an upside
down position on a
clean, scratch resistant
surface.
2. Attach casters on
all four (4) corners of
the mobile pedestal
using four (4) screws
per caster.
3. Turn the mobile
pedestal to an upright
position.
1
2
GLIDE
1
Apply stickers on all visible cam joint faces to
cover the connector faces, after assembly.

Page 3 of 5
939500310 Rev A
1
2 3
4 5





TAB
45º or 2:00
C
L
PLASTIC PLUG
COVER
COIN OR
HEAD OF KEY
PLASTIC PLUG
TURN 90o
3:00
45º
PLUG RETAINER TAB
Removal of Plastic Lock Plug and
Installation of Lock Cylinder
1. Pull open plastic plug cover.
2. While pressing the plug retainer tab to the right,
insert a coin or the head of a key into the slot and
turn 90º clockwise. This will unlock the case. You will
hear the lock mechanism open.
3. Push plug retainer tab down and remove plastic
plug from parent unit.
4. Position lock cylinder tab at 45º or 2:00 position.
Insert lock cylinder at a tilted angle so the tab will
collapse.
5. Push lock cylinder into the hole until it stops and
turn the lock plug assembly clockwise 45º (or the
3:00 position) and remove the key.
CAUTION: Make sure you unlock the
case BEFORE proceeding to step 3.
CAUTION: Make sure the tab is
located at 45º or 2:00 before
inserting lock cylinder.
CAUTION: Failure to
follow the installation
instructions will cause
inability to install lock.
PLUG RETAINER TAB

Page 4 of 5
939500310 Rev A

27"
1/16" R
2 PLACES
1-1/2"
3"
4-3/8"
5"
3/16" DIA
CENTER LINE
OF DESK
TEMPLATE
DESKTOP
TEMPLATE
Screen and Post Assembly
Tops are shipped without screen
mounting holes. To attach screens, holes
must be drilled on site using the supplied
template. Plugs are available through
Customer Service Parts (TS5YGMTSR)
when screens are not in use and have
been removed from the top.
Screens can be mounted above the
worksurface as privacy screens, below
the worksurface as modesty screens, or
above and below to serve both purposes.
Below are several versions of screen
mounting configurations.
1. Make sure that the drilled holes are perpendicular
to the top surface to ensure that the posts assemble
correctly.
2. Cut out template.
3. Measure and mark centerline of desk with pencil.
4. Trace the hole onto the top using a ball point pen.
After you have traced all the holes needed for the
screens, drill through the worksurface from the top side
down using a sharp 5/16" diameter drill bit.

Page 5 of 5
939500310 Rev A
5. Single Post Assembly
1/4-20 BOLT
SMALL WASHER
WASHER
WASHER
5/16-18 BOLT
WORKSURFACE
TOP BRACKET
POST
BOTTOM BRACKET