Teknik Boulevard Cafe 5420650 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Boulevard Cafe L-Shaped Desk
Model 5420650
The oriinal desktop.
Teknik
www.teknikoffice.co.uk

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
Skip the power trip.
This time.
3
4-5
6-38
39-43
44-48
49-50
51
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LARGE LEFT END (1)
B LARGE WIRE BACK (1)
C LONG SHELF (2)
D SHELF TUBE (3)
E SMALL TOP (1)
F BOX RIGHT END (1)
G BOX LEFT END (1)
H BOX FRONT (1)
J BOX BOTTOM (1)
K RIGHT BOTTOM (1)
L BACK(1)
M LARGE RIGHT END (1)
N SHORT RIGHT TUBE (2)
O LARGE UPRIGHT (1)
P REAR RIGHT TUBE (1)
Q SHORT BACK (1)
R SMALL WIRE BACK (1)
S SMALL LEFT END (1)
T SHORT LEFT TUBE (2)
U LEFT BOTTOM (1)
V SMALL RIGHT END (1)
W SMALL LEFT UPRIGHT (1)
X SMALL RIGHT UPRIGHT (1)
Y SHORT TUBE (2)
Z LONG BACK (1)
AA LARGE TOP (1)
BB LONG LEFT TUBE (1)
CC FRONT RIGHT TUBE (1)
DD SHELF (1)
EE DOOR (1)
FF LARGE DRAWER FRONT (1)
GG SMALL DRAWER FRONT (1)
HH DRAWER SIDE (4)
II LARGE DRAWER BACK (1)
JJ LARGE DRAWER BOX FRONT (1)
KK DRAWER BRACE (2)
LL LARGE DRAWER BOTTOM (1)
MM SMALL DRAWER BACK (1)
NN SMALL DRAWER BOX FRONT (1)
OO SMALL DRAWER BOTTOM (1)
Pae 3
A
B
C
C
D
D
E
HJ
K
LM
N
N
O
P
Q
R
ST
T
U
V
W
X
Z
AA
BB
CC
DD
EE
FF
GG
HH
HH
HH
HH
II JJ
LL
MM
NNOO
Y
KK
D
G
F

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
L-WRENCH - 1
36
LARGE HIDDEN
CAM - 2
25
WOOD DOWEL - 7
30
SMALL HIDDEN
CAM - 15
26
METAL BRACKET - 7
29
(EXTENSION SET SHOWN SEPARATED)
EXTENSION RAIL - 4
23 EXTENSION SLIDE - 4 24
APPLIQUE CARD - 1
34
32
MAGNETIC CATCH
SPACER - 1
MAGNETIC CATCH - 1
31
CAM SCREW - 13
27 LONG CAM
SCREW - 4
28
33 GROMMET - 3 METAL PIN - 4 35
Pae 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 5/8" FLAT HEAD SCREW - 14
43 BLACK 9/16" LARGE HEAD SCREW - 24 44
BLACK 1/2" PAN HEAD SCREW - 4
45
BLACK 13/16" PAN HEAD SCREW - 2
41
BLACK 1-3/4" PAN HEAD SCREW - 6
37
BLACK 5/8" PAN HEAD SCREW - 3
42
BLACK 3/8" HEX HEAD SCREW - 19
47
BLACK 7/8" HEX HEAD SCREW - 5
40
BLACK 1-3/8" HEX HEAD SCREW - 25
39
BLACK 1-9/16" FLAT HEAD SCREW - 30
38
BLACK 1/2" FLAT HEAD SCREW - 24
46
Pae 5

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push two LARGE HIDDEN CAMS (25) into the SMALL
RIGHT END (V).
Arrow
25
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
Arrow
V
Pae 6
(2 used)

å Push fifteen SMALL HIDDEN CAMS (26) into the SMALL
LEFT END (S), BOX ENDS (F and G), BOX FRONT (H), BOX
BOTTOM (J), UPRIGHTS (X and W) and LONG BACK (Z).
Step 2
Arrow
26 (15 used)
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
Arrow
W
X
S
H
J
F
G
Pae 7
Z
Arrow
26

å Fasten seven METAL BRACKETS (29) to the
SMALL RIGHT UPRIGHT (X), SHORT BACK (Q),
and LONG BACK (Z). Use seven BLACK 5/8"
FLAT HEAD SCREWS (43).
å Turn thirteen CAM SCREWS (27) into the
SMALL TOP (E), LARGE TOP (AA), SMALL
RIGHT UPRIGHT (X), and BOX FRONT (H).
Step 3
X
Q
Z
BLACK 5/8" FLAT HEAD SCREW
(7 used for METAL BRACKETS)
43
E
AA
H
29
29
27
Pae 8
(7 used)
(13 used)
27

å Turn four LONG CAM SCREWS (28) into the LARGE TOP (AA)
and SHORT TUBES (Y).
Step 4
AA
Y
Y
28
Pae 9
Remember:
Rihty tihty.
Lefty loosey.

å Fasten the LARGE LEFT END (A) to the LARGE WIRE
BACK (B). Tihten two BLACK 1-3/8" HEX HEAD
SCREWS (39) usin the L-WRENCH (36).
Step 5
BLACK 1-3/8" HEX HEAD SCREW
(2 used in this step)
39
36
A
B
Pae 10