Teknik 5423547 User manual

www.teknikoffice.co.uk
Avon Leather Handled Wall Desk
Model 5423547
For things 'n such.
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
3
3
4-9
10-11
12-13
14
15
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Electric drill with 1/8"
and 3/16" or 6mm bits
(ONLY in indicated step)
Pencil
Tape Measure
Level
Page 2
Hammer
Table of Contents Assembly Tools Required

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A WALL SUPPORT (1)
B WALL UNIT (1)
A
B
Page 3www.sauder.423547
DRYWALL ANCHOR - 2
2
SILVER 2" FLAT HEAD SCREW - 2
4
METAL BRACKET - 2
1
SILVER 1-3/8" FLAT HEAD SCREW - 2
5
L-WRENCH - 1
3
SILVER 1/2" HEX HEAD SCREW - 2
6
Hardware Identification

Step 1
å Your Wall Desk is intended to be fastened to wall studs using the included hardware.
å If you need to drywall hang this unit, purchase a drywall anchor which is rated to support a MINIMUM of
80 lbs. Follow the instructions provided with the anchoring hardware.
å Determine the desired height of the Wall Desk on your wall and subtract 7". Mark this location on your wall.
This will be the bottom edge of the WALL SUPPORT (A).
å Locate and mark the wall stud locations on your wall.
å NOTE: BE SURE THE TWO MARKS ON THE STUDS ARE LEVEL BEFORE DRILLING.
7"
Desired upper line of wall unit
Lower edge line of WALL SUPPORT
Wall
Stud
Angled edge
Page 4

StepStep 2
å Drill a 1/8" hole in your wall at each wall stud location.
å Fasten the WALL SUPPORT (A) to your wall using two
SILVER 2" FLAT HEAD SCREWS (4) into the 1/8" holes.
7"
Upper line of wall unit
Lower line of WALL SUPPORT (A)
Wall
Stud
SILVER 2" FLAT HEAD SCREW
(2 used in this step)
4
A
Angled edge
Page 5

Step 3
å Fasten the METAL BRACKETS (1) to the WALL UNIT (B). Turn two SILVER 1/2" HEX HEAD SCREWS (6) with
the L-WRENCH (3).
å Hang your WALL UNIT (B) onto the WALL SUPPORT (A).
å With a pencil, create a mark onto the wall through the METAL BRACKET holes.
å Carefully lower your WALL UNIT (B) to the floor.
B
Page 6
B
SILVER 1/2" FLAT HEAD SCREW
(2 used in this step)
6
1
larger hole
3

Step 4
å 1. On each pencil mark, drill a 3/16" or 6mm hole for the
DRYWALL ANCHOR (2) or 1/8" hole into a stud in the wall.
å 2. Gently tap a DRYWALL ANCHOR (2) into each hole
until it is flush with the wall.
å NOTE: Stud attachment will not use a DRYWALL
ANCHOR.
2.
1.
Drill an 3/16" or 6mm hole for
the DRYWALL ANCHOR.
Drill an 1/8" hole into a
stud in the wall.
2
Wall
Stud
Page 7

å Hang your WALL UNIT (B) onto the WALL SUPPORT.
å Fasten the WALL UNIT (B) to the wall by turning two
SILVER 1-3/8" FLAT HEAD SCREWS (5) through the
METAL BRACKETS and into the DRYWALL ANCHORS or
stud in the wall.
Step 5
SILVER 1-3/8" FLAT HEAD SCREW
(2 used in this step)
5
B
Page 8

å NOTE: Please read the back pages of the instruction
booklet for important safety information.
å This completes assembly. Clean with your favorite
furniture polish or a damp cloth. Wipe dry.
Step 6
10 lbs.
10 lbs.
25 lbs.
Page 9

WARNING
Please use your furniture correctly and safely. Improper use can cause safety hazards,
or damage to your furniture or household items. Carefully read the following chart.
Look out for: What can happen: How to avoid the problem:
• Properly mounting the unit to the wall. • If not properly mounted, the unit can fall
from the wall and cause injury and damage. • Carefully review and follow the mounting instructions contained in this manual.
• Overloaded shelves. • Risk of injury or property damage.
• Overloaded furniture can break. • Never exceed the weight limits shown in the instructions.
• Improper use of furniture to support TV’s.
• Placing TV’s on furniture items not
intended to support them is hazardous.
• Risk of injury or death. TV’s can be very
heavy. Plus the weight and location of
the picture screen can make furniture tip
forward.
• This product is not designed to support a
television.