Teknik 5427430 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS
IMPORTANT SAFETY
INFORMATION.
PLEASE READ AND KEEP
FOR FUTURE REFERENCE.
English pg 1-18
Français pg 19-21
Español pg 22-24
11/12/21 Lot # 573391
Purchased:
__________________
Hutch for storage units
Hudson Elm finish | Model 5427430
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
6
7-18
19-21
22-24
25-26
27
Tape Measure
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D SHELF (2)
E LOWER BACK (1)
F BACK (2)
A
B
C
D
D
E
F
F
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
TAPE CARD/
PREP PAD KIT - 1
182M
Isopropyl
Alcohol 70%
Prep Pad
10M TOUCH-UP PEN - 1
1F HIDDEN CAM - 18 2F CAM DOWEL - 18
BLACK 1-15/16" FLAT HEAD SCREW - 6
113S
TWIST-LOCK®
FASTENER COVER - 12
125P
42F WOOD DOWEL - 2
FURNITURE TIPPING
RESTRAINT KIT - 1
97
Page 4
CAM
COVER - 18
129P

Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the edge
of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
HOW TO USE A HIDDEN CAM & CAM DOWEL
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3.
Page 6

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push eighteen HIDDEN CAMS (1F) into the BACKS (E and F).
Then, insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM in the long edges of the BACKS.
F
E
F
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
(12 used) (6 used)
Arrow
1F
Page 7
1F
2F
Arrow
Metal end

Step 2
å Fasten one of the SHELVES (D) to one of the BACKS (F).
Use three BLACK 1-15/16" FLAT HEAD SCREWS (113S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
D
Surface without HIDDEN CAMS
Surface with TWIST-LOCK® FASTENERS
F
BLACK 1-15/16" FLAT HEAD SCREW
(3 used in this step)
113S
Page 8
Some assembly
(and snacks) required.

Step 3
å Push the remaining BACK (F) onto the SHELF (D). Do not
tighten the HIDDEN CAMS.
D
Surface without HIDDEN CAMS
Surface with TWIST-LOCK® FASTENERS
F
Page 9

å Fasten the remaining SHELF (D) to the BACK (F). Use
three BLACK 1-15/16" FLAT HEAD SCREWS (113S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
å Push the LOWER BACK (E) onto the SHELF (D). Do not
tighten the HIDDEN CAMS.
Step 4
D
Surface with TWIST-LOCK® FASTENERS
Surface without TWIST-LOCK® FASTENERS
F
E
BLACK 1-15/16" FLAT HEAD SCREW
(3 used in this step)
113S
Page 10

Step 5
å Insert the plastic end of a CAM DOWEL (2F) into the
holes shown in the LEFT END (B).
å Fasten the LEFT END (B) to the SHELVES (D). Tighten four
TWIST-LOCK® FASTENERS.
å NOTE: Be sure the CAM DOWELS in the LEFT END insert
into the HIDDEN CAMS in the BACKS.
D
B
D
F
F
E
Surface with
TWIST-LOCK®
FASTENERS
Edge with TWIST-LOCK® FASTENERS
Do not tighten the HIDDEN CAMS in this step.
Page 11
Plastic end
2F
(6 used)