Teknik Boulevard Cafe 5420650 User manual

www.teknikoffice.co.uk
Boulevard Cafe L-Shaped Desk
Model 5420650
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
For all your
newfangled gadgetry.
Teknik

Table of Contents Assembly Tools Required
3
4
5-38
39-43
44-48
49-50
51
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Page 2
Straight Edge Screwdriver

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A LARGE RIGHT END (1)
B LARGE LEFT END (1)
C SMALL RIGHT END (1)
D SMALL LEFT END (1)
E LARGE UPRIGHT (1)
F SMALL TOP (1)
G LARGE TOP (1)
H SMALL RIGHT UPRIGHT (1)
I SMALL LEFT UPRIGHT (1)
J SHORT BACK (1)
K SMALL WIRE BACK (1)
L LONG BACK (1)
M LONG SHELF (2)
N LARGE WIRE BACK (1)
O BACK (1)
P SHELF TUBE (3)
Q BOX LEFT END (1)
R BOX FRONT (1)
S BOX RIGHT END (1)
T BOX BOTTOM (1)
U SHELF (1)
V RIGHT BOTTOM (1)
W LEFT BOTTOM (1)
X SHORT LEFT TUBE (2)
Y SHORT RIGHT TUBE (2)
Z LONG LEFT TUBE (1)
AA SHORT TUBE (2)
BB FRONT RIGHT TUBE (1)
CC REAR RIGHT TUBE (1)
DD LARGE DRAWER FRONT (1)
EE SMALL DRAWER FRONT (1)
FF SMALL RIGHT DRAWER SIDE (1)
GG SMALL LEFT DRAWER SIDE (1)
HH SMALL DRAWER BACK (1)
II SMALL DRAWER BOTTOM (1)
JJ LARGE RIGHT DRAWER SIDE (1)
KK LARGE LEFT DRAWER SIDE (1)
LL LARGE DRAWER BACK (1)
MM LARGE DRAWER BOTTOM (1)
NN LARGE DRAWER BRACE (1)
OO DOOR (1)
Now you know
our ABCs.
Page 3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
RS
T
U
V
WY
Z
BB
CC
DD
EE
FF
GG
HH
II
JJ
LL
MM
OO
M
P
P
Y
NN
AA
XKK
X

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
(EXTENSION SET SHOWN SEPARATED)
1EXTENSION RAIL - 4 2EXTENSION SLIDE - 4 LARGE CAM
SCREW - 14
4
LARGE HIDDEN
CAM - 28
3
WOOD
DOWEL - 7
7
BLACK APPLIQUE
CARD - 1
13
SMALL HIDDEN
CAM - 10
5
BLACK 1-1/2" FLAT HEAD SCREW - 21
17
L- WRENCH - 1
14
SMALL CAM
SCREW - 24
6
BROWN APPLIQUE
CARD - 1
12
METAL
BRACKET - 3
8
BLACK 1-3/8" HEX HEAD SCREW - 25
16
BLACK 5/8" PAN HEAD SCREW - 2
18
BLACK 1/2" HEX HEAD SCREW - 23
20
BLACK 1/2" LARGE HEAD SCREW - 30
19
BLACK 1/2" FLAT HEAD SCREW - 4
21 BLACK 1/2" PAN HEAD SCREW - 24 22
GROMMET
WITH CAP - 3
11
SHELF PIN - 4
9
BLACK 2-1/4" PAN HEAD SCREW - 4
15
MAGNETIC
CATCH - 1
10

Page 5
Step 1
å Assemble your unit on a carpeted floor or on the empty carton to
avoid scratching your unit or the floor.
å Push twenty-eight LARGE HIDDEN CAMS (3) into the SMALL
ENDS (C and D), SMALL UPRIGHTS (H and I), BACKS (J and L),
BOX FRONT (R), BOX ENDS (Q and S), and BOX BOTTOM (T).
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Arrow
Arrow
3
C
D
H
I
J
L
R
T
Arrow
3
Arrow
3
(28 used)
S
Q

Step 2
å Turn fourteen LARGE CAM SCREWS (4) into the exact holes
shown in the TOPS (F and G), SMALL RIGHT UPRIGHT (H),
and BOX FRONT (R).
å Push ten SMALL HIDDEN CAMS (5) into the DRAWER
SIDES (FF, GG, JJ, and KK) and LARGE DRAWER BRACE (NN).
Page 6
F
R
H
G
4
4
4
5
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
(10 used)
Arrow
FF
GG
JJ
NN
KK

å Turn twenty-four SMALL CAM SCREWS (6) into the exact
holes shown in the SMALL RIGHT END (C), LARGE TOP (G),
SHORT TUBES (AA), and DRAWER FRONTS (DD and EE).
å NOTE: The SMALL CAM SCREWS are turned into the metal
portion of the part.
Step 3
Page 7
EE
G
DD
C
AA
6
(24 used)
6
6

Step
Page 8
Step 4
å Fasten the LARGE LEFT END (B) to the LARGE WIRE
BACK (N). Tighten two BLACK 1-3/8" HEX HEAD
SCREWS (16) using the L-WRENCH (14).
BLACK 1-3/8" HEX HEAD SCREW
(2 used in this step)
16
14
B
N
Just think. The sooner
you do this, the sooner
you do something else.

StepStep 5
å NOTE: Be sure to keep SCREWS (19) separate from
SCREWS (22). Do not confuse these SCREWS.
å Fasten the SHELF TUBES (P) to the LONG SHELVES (M).
Use fifteen BLACK 1/2" LARGE HEAD SCREWS (19).
å NOTE: Be sure SHELF TUBES wrap around the edges of
the LONG SHELVES.
Page 9
P
M
P
These edges
should be even.
These edges
should be even.
Surface with holes
M
P
Surface with holes
BLACK 1/2" LARGE HEAD SCREW
(15 used in this step)
19

Step
å Fasten the LONG SHELF (M) with one SHELF TUBE (P) to
the LEFT END (B). Tighten one BLACK 1-3/8" HEX HEAD
SCREW (16) using the L-WRENCH (14).
å Fasten the LONG SHELF (M) to the LARGE WIRE BACK (N).
Use five BLACK 1/2" LARGE HEAD SCREWS (19).
Step 6
14
B
N
BLACK 1-3/8" HEX HEAD SCREW
(1 used in this step)
16
Surface with screws
M
Page 10
BLACK 1/2" LARGE HEAD SCREW
(5 used in this step)
19
P