Teknik Barrister Home 5418705 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Barrister Home Night Stand
Barrister Home Collection | Model 5418705
Sweet stand.
Sweet dreams.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
3
4-5
6-23
24-26
27-29
30
31
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Pae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E SHELF (1)
F BACK (1)
G BRACE (1)
H BASE (1)
I RIGHT BASE (1)
J LEFT BASE (1)
K DRAWER FRONT (1)
L FRONT MOLDING (1)
M RIGHT MOLDING (1)
N LEFT MOLDING (1)
O SHELF MOLDING (1)
D24 DRAWER RIGHT SIDE (1)
D25 DRAWER LEFT SIDE (1)
D163 DRAWER BACK (1)
D723 DRAWER BOTTOM (1)
M67 DRAWER BRACE (1)
Now you know
our ABCs.
Pae 3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
D24
M67
D25
D723
D163

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
UEXTENSION SLIDE - 2 TEXTENSION RAIL - 2
(EXTENSION SET SHOWN SEPARATED)
METAL BRACKET - 5
4G
METAL PIN - 2
1R
MOLDING
CONNECTOR - 2
19F
10A SLIDE CAM - 2
NAIL - 24
1N
HIDDEN CAM - 13
1F CAM DOWEL - 13 2F
PULL - 1
70K
KNOB - 1
71K
Page 4
40AW CABINET RIGHT - 1 40AX CABINET LEFT - 1 40AY DRAWER RIGHT - 1
40AZ DRAWER LEFT - 1

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Pae 5
SILVER 3/4" MACHINE SCREW - 1
20S
BLACK 9/16" LARGE HEAD SCREW - 10
1S
SILVER 1-1/8" FLAT HEAD SCREW - 7
10S
BLACK 1-1/4" FLAT HEAD SCREW - 4
7S
BLACK 7/8" MACHINE SCREW - 2
37S
18S BROWN 1" FLAT HEAD SCREW - 4
3S GOLD 5/16" FLAT HEAD SCREW - 12
30S BLACK 1-9/16" FLAT HEAD SCREW - 5

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push thirteen HIDDEN CAMS (1F) into the ENDS (A
and B), BOTTOM (D), SHELF (E), BRACE (G), and
DRAWER BRACE (M67). Then, insert the metal end
of a CAM DOWEL (2F) into each HIDDEN CAM.
Pae 6
Arrow
1F
2F
(13 used)
Arrow
1F
2F
Do not tihten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
A
B
E
G
M67
D

StepStep 2
å Separate the EXTENSION SLIDES (U) from the EXTENSION RAILS (T) as
shown in the enlared diaram below. Be prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (T) to the ENDS (A and B). Use GOLD 5/16"
FLAT HEAD SCREWS (3S).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in
the enlared diaram. Then, slide the inner cartride of the EXTENSION
RAIL in to find the other hole that lines up with the hole in the END. Turn a
SCREW into this hole.
Pae 7
Open end
Open end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Push the black lever in and pull the SLIDE from the RAIL.
A
Surface with
HIDDEN CAMS
B
Surface with
HIDDEN CAMS
Ede with
CAM DOWELS
Ede with
CAM DOWELS
TU
T
T

StepStep 3
å Tap two MOLDING CONNECTORS (19F) into the notches
in the MOLDINGS (L, M, and N).
Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS.
Flat end
Flat end
19F
M
N
L
19F
Unfinished surface
Unfinished surface
Unfinished surface
Pae 8
Some assembly
(and snacks) required.

StepStep 4
å Fasten the TOP (C) to the MOLDINGS (L, M, and N). Use
seven SILVER 1-1/8" FLAT HEAD SCREWS (10S).
å NOTE: Do not overtihten the SCREWS into the TOP.
Pae 9
C
L
N
M
Finished surface
Finished surface
Surface
with holes
Finished surface
SILVER 1-1/8" FLAT HEAD SCREW
(7 used in this step)
10S
Do not overtihten
the SCREWS (10S).
Lon curved ede

Step
å Fasten the LEFT END (B) to the BOTTOM (D). Tighten two
HIDDEN CAMS.
Step 5
Page 10
Surface
with
HIDDEN
CAMS
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
B
D
Surface with
HIDDEN CAMS
These holes must be here.
This hole must be here.