Victory 4x4 OFF-GRID FRIDGE SLIDE User manual

OFF-GRID FRIDGE SLIDE
Thank you for purchasing from Victory 4x4! Checkout our website, victory4x4.com for other great o-road
products. Be sure to rate and review our product online. If you have any questions or are missing parts, please
don’t hesitate to call us at 269-459-8447!
INSTALLATION INSTRUCTIONS
Please read the mounting instructions below carefully before attempting to install.
Check out the install video on the product page for more detailed information.

INCLUDED HARDWARE
16x
46x
16x
1/4” ID Black
Washer
1/4"-20
Serr. Flange Nut
1/4"-20 X 1/2"
Button Head
30x 1/4"-20 X 3/8"
Button Head
34x
1/4" Flat
Nuts
1x Loctite Packet

INCLUDED PARTS
1x
1x
1x
2x 1x 1x
2x
1L/1R

Start by taking the (2) provided slides and bolt each one to the insides of
the provided floor mounts, making sure the red handles are pointing out,
as shown in the orientation below. Make sure to use (4) each per side of
the provided shorter 1/4” button heads, washers and flat nuts and apply
the provided blue loctitie to the bolts before tightening. You will need to
extend the slide to access some of the mounting holes on the inside.
ASSEMBLY
1.

ASSEMBLY
2. Once you have that assembled, you can now bolt the cabinet assembly
to your floor through the bottom mounting holes on each side using the
longer 1/4” button heads and washers to secure into nutstrips. For more
details on our vehicle specific floor systems, be sure to check out our
product page on our website and watch our install video.
3. Next you need to decide if you are going to mount the provided “U”
shaped fridge slide platform upright or upside down, depending on the size
of your fridge. If your fridge is wider than 18” then you will need to mount
it upside down so the fridge can overhang the sides. Just be aware that
your fridge will now sit 3.5” taller if mounted upside down and sitting on
top opposed to sitting inside the tray. You will mount the bracket to the
slides with the provided 1/4” button heads, washers and flat nuts as shown
in the orientation below.

ASSEMBLY

ASSEMBLY
4. Once you have your bracket installed to the slides in the orientation of your
choice, you can now bolt the back piece to your bracket. To do so use the
provided 1/4” button heads, washers and nuts as shown in the orientation
below.

ASSEMBLY
5. Once the back piece to the slide platform is attatched, you can now bolt
the front piece to your fridge slide on. Take the provided front bracket
and (2) 1/4” button heads, washers and flange nuts and assemble in the
orientation shown below. If you have your tray is installed upright, like
shown below, that hardware will only be installed temporalily until the
handle is assembled aer step 6. If your tray is installed upside down then
you would mount to the bottom set of holes and those would stay there
permanently.

ASSEMBLY
6. You are now ready to assemble the handle system around the red
latches on the slides. To do so, use (4) of the provided button heads and
secure them through the “PRESS” bracket into the pem nut bracket and
sandwhich them around the red grab handles so they are grabbing them,
as shown in the orientation below.

ASSEMBLY
7. Once the handle is assembled, you now need to place the cover over the
assembly using (6) each of the provided button heads, washers and flange
nuts. This is also the step you need to remove the hardware from step
5 if your tray is facing upright, and then place back over the cover piece.
Assemble in the orientation shown below.

ASSEMBLY
8. Now that your fridge slide is fully assembled, you are now ready to place
your fridge and strap it down using the handles on the fridge and through
the slots on the front and back of the tray piece.
This installation guide shows how to assemble one fridge slide assembly,
but the possibilities are endless! Check out the product page for inspiration
on how to maximize your space by using a combination of O-Grid
Drawers and our O-Grid Fridge Slide!