aivituvin AIR 32 User manual

INSTRUCTION
MANUAL
AIR 32
www.aivituvin.com

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
P1 P2
02
M3.5x40mm SCREW
M4.0x50mm SCREW
10PCS+1spare 22PCS+1spare
P3 P4
M3.5x25mm SCREW
M3.5x35mm SCREW
8PCS+1spare 7PCS+1spare
P5 P6
M3.0x16mm SCREW
10PCS+1spare
Spring latch
3PCS

PARTS
BC
DE
1PC
1PC 1PC
03
1PC
1PC
Front panel of coop
Back panel of coop
Left panel of coop
F
1PC
Right panel of coop
G H
1PC
1PC
Front panel of pen
Back panel of pen
I
1PC
Right panel of pen
A
Back wire panel of coop
Front wire panel of coop

PARTS
J K L
MN
1PC
1PC 1PC
04
1PC
2PCS
Pen roofs
Perch
Back panel of nesting
O
1PC
Front panel of nesting
Ramp Tray
P Q
1PC
1PC
Side panel of nesting box Bottom floor
R
1PC
Divider

PARTS
S T U
1PC 2PCS
05
1PC
Nesting box roofs
Coop roofs Cap
Coop
Pen
Nesting box
V
1PC
PVC Waterproof Strip

PRODUCT ASSEMBLY
01
02
06
Attach the front and back wire panel of coop Part C & D , front and back
panel of pen Part G & H by 6xP1 screws.
Attach the front and back panel of coop Part A & B, left and right panel
of coop Part E & F by 8xP2 screws.
B
EA
D
P
1
X
6P
2
X
8
FHGC

PRODUCT ASSEMBLY
03
07
Screw the ramp Part K to the bottom half of lower panel on Part F
by 4xP5 screws.
K
04
Attach the right panel of pen Part I to the sides by 4xP2 screws.
I
P2
X4
P5
X4

PRODUCT ASSEMBLY
05
08
①
②
Insert 2PCS perches Part M into the slots inside front and back
panel of coop.
Slide in tray Part L.
06
Attach the back panel of nesting box Part N and front panel of nesting
box Part O to the coop by 2xP2 screws on wood Part and 4xP1 screws
on wire part.
L
P2
X2
Mx2
P1
X4
N
O

PRODUCT ASSEMBLY
07
09
Attach the nesting box side panel Part P to the sides by 4xP2
screws.
P
08
①Drop in the bottom floor Part Q to the nesting box.
②Insert the divider Part R into the slots of bottom floor.
P2
X4
Q
R

PRODUCT ASSEMBLY
09
10
Attach the nesting box roof Part S by removable hinge as show on
below pictures.
S
10
Attach the roof panel of pen Part J to the pen by 4xP2 screws.
J
P2
X4

PRODUCT ASSEMBLY
11
11
Attach 2PCS coop roofs Part T to the coop by 8xP3 screws.
P3
X8
Tx2

PRODUCT ASSEMBLY
12
12
①
②
Ensure top roof panels line up with each other before screwing
the cap Part
Attach the spring latch P6 to the front doors by 2xP5 screws each.
(Notice the direction of latch)
U by 4xP4 screws.
U
P4
X4
P6
X1
P5
X2
P6
X2
P5
X4

13
V
P4
X3
13
Attached PVC Waterproof Strip Part V to the nesting box by 3XP4
screws.
PRODUCT ASSEMBLY
Finish

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.