aivituvin AIR 68 User manual

INSTRUCTION
MANUAL
AIR 68
www.aivituvin.com

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
P1 P2
02
M3.5x40mm SCREW
M3.5x45mm SCREW
8PCS+1spare 16PCS+1spare
P3 P4
M3.0x16mm SCREW
M3.5x25mm SCREW
4PCS+1spare 16PCS+1spare
P5 P6
Chewing toy
M3.0x10mm SCREW
2PCS+1spare 1PC
P7
Connecting Piece
4PCS
P8
M3.0x16mm SCREW
12PCS+1spare

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
BC
DE
1PC
1PC
1PC
03
2PCS
2PCS
Front Panel-Right Side
Back Panel-Right Side
Side Panel
House Divider
Run Divider
F
2PCS
Support Bar
G H
2PCS
2PCS
Tray
Wire Floor
I
2PCS
Wooden Floor
A

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
J K L
MN
3PCS
1PC 4PCS
04
2PCS
2PCS
Roof Pen Cover
Roof Cap
Caster With Brake
O
3PCS
Caster Without Brake
Folding metal feeder
1PC
Front Panel-Left Side
PQ
1PC
Back Panel- Left Side

PRODUCT ASSEMBLY
01
02
05
Use the connecting piece P7 to attached Part E by 4XP8 each side.
Screw Part A, B, C,D together by 4XP1 & 4XP2 screws.
P
1
X4
B
C
P
8
X
4
A
P
2
X2
E
D
P
2
X
2
P
7
X
2
P
8
X
4
P
7
X
2

PRODUCT ASSEMBLY
03
06
04
Qx2
x2P
Screw in the casters Part P & Q to the legs.
①
②Slide in the plastic tray Part G.
Put the support bar Part F into the pen.
F
G

PRODUCT ASSEMBLY
05
06
06
Put in the floor Part H & I.
H
I
Attach metal feeder Part J by 2XP5 screw, then put in the chewing toy.
J
P6
X1
P5
X2

PRODUCT ASSEMBLY
07
07
08
Attach the pen roof Part L by 4XP2 screws.
P2
X4
L
Attach the roof Part by 4XP4 screw each side.K
P4
X4
K
P4
X4
K

PRODUCT ASSEMBLY
09
08
Attach the roof cap Part M by 2XP3 screws.
P3
X2
M
10
Screw Part N, O, B, D together by 4XP1 & 4XP2 screws.
Screw in the casters Part P & Q to the legs
Repeat the same assembly ways of Step 2 to Step 9.
①
②
③
Q
P
B
P
1
X4
O
P
2
X2
N
P
2
X2
D