aivituvin AIR 38 User manual

INSTRUCTION
MANUAL
AIR 38
www.aivituvin.com
X

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
Do n ot u se this i t em i n a way in cons iste nt with th e
manufacturer’ s instructions as this could void the product
warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
PCS+1 spare
P1 P2
P3 P4
P5
M3.0x25mm SCREW
M3.0x16mm SCREW
M3.5x40mm SCREW
E
10PCS+1 spare
16PCS+1spare
Che ing To
P6
Bo
1PC
1PCS
1PC
P7
Lock
1PC

PARTS
A B C
DE
G
1PC
PC PC
HI
PCS
1PC
1PC
1PC
1PC
Left panel pper
Front panel Back panel Left panel Down
Right panel UpperRight panel Down
Tray
1PC

PARTS
K L
M
1PC
1PC
Back panel of small house
Top panel of small house
4PCS 1PC
NO
2PCS
Side panels of small
2PCS

PRODUCT ASSEMBLY
01
02
Attach the top panel Part M by 4XP2 screws.
Attach the small house,attach the Part K,L & N by 8XP2
screws.
X
8
X
4

PRODUCT ASSEMBLY
03
①Attach the back panel Part B, Left panel Part E and Part C (With
"Aivituvin"logo by 4X P1 screws.
Small Wooden Slat
downward
With "AIVITUVIN" logo
Line up the same level
X
4
②NOTICE: Do not reverse the back panel and side panels

PRODUCT ASSEMBLY
04
①Attach the right panel Part F and Part D by 4X P1 screws.
NOTICE: Do not reverse the side panel Part F The wooden
slat downward .
:②
X
4
Line up the same level

PRODUCT ASSEMBLY
5
06
08
Attach the 2PCS of right platforms Part I in the Right and Back
corners by 6XP2 screws as show on the picture.
Attach the 2PCS of left platforms Part O in the Left and Back
corners by 6XP2 screws as show on the picture.
X6
X6

PRODUCT ASSEMBLY
07
08
09
Connect 4PCS of Platform by 4PCS Ramp Part J.
Attach the Front panel Part A by 8XP1 screws.
X8

PRODUCT ASSEMBLY
09
① Attach the top cover panel Part G to the house by 4XP3
screws.
X4
10

PRODUCT ASSEMBLY
10
11
Slide in the tray part H

PRODUCT ASSEMBLY
11
12
Attach the tray to the hutch with the lock P7
by 6 X P3screws.
X6X1

PRODUCT ASSEMBLY
12
13
Screw the eye hook P4 to the left panel,tie the rope on one side
of roof, the other side of hook to make the roof open.
4X1

PRODUCT ASSEMBLY
13
14
① Put the small house above the tray.
② Put the chewing toy P5 and bowl P6 into the cage anywhere
you want.
X1
X1
Finish

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whe ther direct,indir ect,or incid ental ,resulting f rom th e inc orrect
attachment,improper use,inadequate miantenance,or neglect of this product.