aivituvin AIR 02 User manual

INSTRUCTION
MANUAL
AIR 02
www.aivituvin.com
X

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
Do not use this item in a way inconsistent with the
manufacturer’ s instructions as this could void the product
warranty.
01

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
14PCS+1 spare
P1 P2
P3 P4
P5
02
M3.5x40mm SCREW
M3.5x35mm SCREW
P6
6PCS+1 spare
M3.5x50mm SCREW
M3.0x16mm SCREW
10PCS+1 spare
18PCS+1 spare
M3.5x25mm SCREW
12PCS+1 spare
3PCS
SPRING LATCH

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
DEF
G
1PC
1PC 1PC
03
HI
1PC 1PC
1PC
1PC
1PC
1PC
Side panel of hutch
Front panel of hutch Back panel of hutch Front panel of pen
Middle access door panel
Side panel of pen Splayed supporting bar
Back panel of pen
Plastic tray

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
J K L
MNO
04
1PC
1PC
1PC
Roof of hutch Roof of pen Roof cap of pen
Ramp
Roof cap of hutch
2PCS 2PCS
1 PC
Roof connect slat ( Only for
2 hutches combination.not
available for one hutch
owner )
Hutch
Pen

PRODUCT ASSEMBLY
01
02
05
Silde in the plastic tray Part H.
① Attach the front Part A,the back Part B to Part E & F by 10xP2.
②Notice to align with the dowels.
A
B
E
P2 X10
F
H

PRODUCT ASSEMBLY
03
04
06
Screw the ramp Part O to the bottom half of lower panel on Part
F by 4xP5.
Screw the splayed supporting bar Part I by 2xP3.
P5
X4
O
P3 X2
I

PRODUCT ASSEMBLY
05
06
07
Attach the front and back pen panel Part C & D to the hutch by
4xP1.
Attach the side pen Part G by 4xP2.
P1 X4
C
D
G
P2 X4

PRODUCT ASSEMBLY
07
08
08
Screw the pen roof panels Part K to the pen by 8xP3.
Ensure the top roof panels line up with each other before screwing
Part L by 4xP4.
P3 X8
Kx2
P4 X4
L

PRODUCT ASSEMBLY
09
10
09
Ensure the top roof panels line up with each other before screwing
Part M by 4xP4.
Screw the roof panels Part J to the hutch by 8xP3.
P3 X8
Jx2
P4 X4
M

PRODUCT ASSEMBLY
11
10
Attach the spring latch P6 to the doors by 2xP5 each.
P6
X3
P6
X6
P5
Finish here for only buying one hutch !

11
Notice
Read Before Assemble!
① Pls ignore the following for only one hutch owner !
② There are 2 different combinations for your optional choice.
Option 1
+=
Option 2
+=

OPTION 1
12
13
12
①Take out the lock of 1st hutch.
②Push upward the hinge to take out the door.
Push upward
to take out
①Repeat Step 1 to Step 11 to assemble 2nd hutch.
②Take out the lock.
③Screw out the hinge to take out the door of 2nd hutch.
Screw out the hinge
to take out the door.

PRODUCT ASSEMBLY
14
13
Attach the 1st hutch to 2nd hutch by 2xP1.
P1
X2
P1
15 Repeat the combination assembly in the opposite side by
2xP1.
P
1
X2
P1

OPTION 2
16
17
14
①Take out the lock of 1st hutch.
②Push upward the hinge to take out the door.
Push upward
to take out
①Attach the front Part A, the back Part B to the sides Part F & E
by 10xP2.
②Notice the direction of Part F & E is different with the 1st hutch
( Very important ! )
X10
P2
A
F
E
B

PRODUCT ASSEMBLY
18
19
15
Screw the ramp Part O to the bottom half of lower panel on Part
F by 4xP5.
Slide in the plastic tray Part H.
H
X4
P5
O

PRODUCT ASSEMBLY
20
21
16
Attached the front and back pen panel Part C & D to the hutch
by 4xP1.
Screw the splayed supporting bar Part I by 2xP3.
X2
P3
I
X4
P1
D
C

PRODUCT ASSEMBLY
22
23
17
Attach the side panel Part G by 4xP2.
2
PX4
G
①Take out the lock.
②Push upward the hinge to take out the door.
Push upward
to take out

PRODUCT ASSEMBLY
24
18
Ensure the top roof panels line up with each other before screwing
Part L & M by 4xP4 each. (Finish here for second hutch assemble) .
①Screw the roof panels Part J & K to the hutch and pen by
8xP3 each.
Attach the spring latch P6 to the door by 2xP5 each.
②
X16
P3
Kx2
Jx2
5PX4
5PX2
6
P
25
6P5P4X8
L
M