aivituvin AIR 65 User manual

INSTRUCTION
MANUAL
AIR 65
www.aivituvin.com
X

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
P1 P2
P3 P4
P5
02
M3.5x45mm SCREW
M3.5x35mm SCREW
M3.5x60mm SCREW
8PCS+1spare
10PCS+1spare
12PCS+1spare
24PCS+1spare
M3.5x25mm SCREW
4PCS+1spare
M3.0x16mm SCREW
P6
M3.5x40mm SCREW
8PCS+1spare
P7
Lock
2PCS

A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
ABC
EF
G
1PC
1PC 1PC
03
HI
1PC
1PC
1PC
1PC
1PC Right Side Panel
Front Panel- Upper
Front Panel- Down Back Panel
Tray-Upper
Left Side Panel
3PCS
Tray-Down Wire Pen Ramp Support
D
PARTS

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
2PCS
1PC 1PC
1PC 4PCS
2PCS
2PCS Roof of Hutch
Wire Pen-Right Back
Ramp Side Wire Pen
Roof Cap
Tray of Pen
4PCS
Back casters with brakes Front casters without
brakes
J K L
MN
QR
04
P
2PCS
Roof of Pen
O
S
Back Panel-Down
1PC

PRODUCT ASSEMBLY
01
02
Attach the casters without brakes 2Xpart R in front and the casters with
brakes 2Xpart Q in back.
Attach the panel part A,B,C,D,E,S by 16XP2 screws.
P2X
16
B
C
05
A
D
E
S
R
Q
R

PRODUCT ASSEMBLY
03
04
②Attach the wire pen part H to the left side of hutch by 4XP1 screws.
①Slide in the tray part F & G.
①Attach the wire pen part H & J to the right side of hutch by 4XP1
screws.(Please pay attention the position of part J)
②Attach the ramp support part I to the part J by 2XP1 screws.
H
J
P1
X4
I
H
P1
X4
06
H
P1
X2
F
G

PRODUCT ASSEMBLY
05
06
Screw the ramp part K to the right side panel by 4XP5 screws.
Attach the 2Xpart R to the front of part L.
Attach the 2Xpart Q to the back of part L.
P
5
X4
K
R
07
Q
R
Q
L
L

PRODUCT ASSEMBLY
07
08
08
Attach the roof of pen part M by 4XP6 screws each side.
M
P
6
X8
M
L
P
2
X4
L
P
2
X4
Attach the side wire pen part L by 4XP2 screws each side.

PRODUCT ASSEMBLY
09
10
09
Attach the roof of hutch part O by 8XP3 screws.
O
P
3
X8
Slide in the tray part N.
N