aivituvin AIR 10 User manual

INSTRUCTION
MANUAL
AIR 10
www.aivituvin.com
X

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
P1 P2
P3 P4
P5
02
M3.5x40mm BOLT
M3.5x25mm SCREW
M3.5x50mm SCREW
16PCS+1spare
4PCS+1spare
2PCS+1spare
P6
2PC
18PCS+1spare
M3.0x16mm SCREW
14PCS+1spare
M3.0x10mm SCREW
P7 P8
1PC
1PC

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
DEF
G
1PC
1PC 1PC
03
HI
1PC
1PC
1PC
1PC
1PC
Back panel of pen
Front panel of hutch
Back panel of hutch Right panel of hutch
Left side panel of pen
Front panel of pen
2PCS
Divider panel Bottom wire netting Upper tray

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
J K L
MNO
P
1PC
1PC 1PC
04
QR
2PCS
1PC
1PC
1PC
1PC
Small ramp outside the
hutch
Lower tray
Pen roof - UV proof Hutch roof
Folding metal feeder
Ramp
2PCS
PVC curtain Casters without brake Brake casters

PRODUCT ASSEMBLY
01
02
05
Attach Part G to Part A and Part B by 4pcs of P2 screws.
Attach Part A, Part B and Part C by 6pcs of P2 screws.
P2X
6
A
G
C
B
P2X
4

PRODUCT ASSEMBLY
03
04
06
Attach the pen Part D, Part E, Part F by 4pcs of P2 screws.
Attach the pen to hutch by 2pcs of P1 screws.
P2
X4
P1
X2
F
E
D

PRODUCT ASSEMBLY
05
06
07
Repeat on the other side.
Slide in the tray Part J.
P1X2
J

PRODUCT ASSEMBLY
07
08
08
①Put in 2pcs of Part H to be UPWARDS direction to seperate the
urine & poop.
②Then slide in the tray Part I.
①Screw the feeder to Part C by 2pcs of P5 screws.
②Then put in the rabbit chewing toy P6.
O
Hx2
I
P5
X2
P6
X1

PRODUCT ASSEMBLY
09
10
09
①Screw the ramp Part M to the bar on the Part G by 4pcs of
P4 screws.
Screw the roof hinge to the back by 3pcs of P4 screws on each
side.
P8X2
N
L
P4X6
②Screw 2pcs of eye hook P8 on the front door of pen.
(The are pre-drilled holes to screw in)
Then hang with the front ramp.{Use only when needed}
M
P4X4

PRODUCT ASSEMBLY
11
12
10
Screw the roof hinge P7, one side to the roof by P4x2 the other
side to the right panel by P4x2.
①Attach the pen roof Part K by 4pcs of P2 screws.
②Stick PVC curtain "P" to the hutch door.
P2X4
P7X1
K
P4X4
P

PRODUCT ASSEMBLY
13
1 4
11
Screw two casters without brake Part Q to the front of hutch legs by
P3x8.
Screw two brake casters Part R to the back of hutch legs by P3x8.
P3
X8
Qx2
LOCKED
OPEN
P3
X8
Rx2

HELP CENTER
[email protected]
Question about your product? we're here to help contact us via
Returns & Refunds
?
Product AssemblyOrders FAQProduct inquiry
THANK YOU
Thanks for your support to Aivituvin.
Your satisfaction is our #1 priority.
Once the items are received, opened, and deemed to be faulty
or other problems.
Pls contact us at [email protected] for the solution.
We will feedback to you within 24 hours.
If you are happy with the shopping ,welcome to share photos
and thoughts with others .
www.aivituvin.com
12

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.