aivituvin AIR 77 User manual

INSTRUCTION
MANUAL
AIR 77
www.aivituvin.com
X

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
P1 P2
P3 P4
P5
02
M3.5x35mm SCREW
M3.5x25mm SCREW
M3.5x45mm SCREW
16PCS+1spare
8PCS+1spare
16PCS+1spare
P6
8PCS+1spare
M3.0x20mm SCREW
4PCS+1spare
M3.0x16mm SCREW
2PCS
Roof hinge
M4.0x20 mm BOLT
2PCS+1 spare
P7

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
D E F
G
1PC
1PC 1PC
03
HI
1PC
1PC
1PC
1PC Right Panel
Upper Back Panel
Lower Back Panel Metal ramp supporting
Upper Front Panel
Left Panel
Lower Front Panel
2PCS
Casters without brake Brake casters
2PCS

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
J K L
M N O
1PC
2PCS 1PC
04
1PC
1PC
1PC Divider
Tray Supporter
Lower Tray
Roof
Ramp
Upper Tray

PRODUCT ASSEMBLY
01
02
05
Attach the back panel to the side panels Part D & E by 8XP2 screws.
①Attach the back panel Part A and B by 4XP4 screws.
②Attach the ramp supporter Part C by 2XP7screws.
P4X
4
P2X
8
A
B
A
C
B
P7X
2
D
E

PRODUCT ASSEMBLY
03
04
06
Attach the front panel Part F & G by 8XP1 screws.
Attach the caster Part H & I by 4XP3 screws each.
P1
X8
G
F
P3
X8
Ix2
P3
X8
Hx2

PRODUCT ASSEMBLY
05
06
07
Put the tray supporter Part J into the slot.
Slide in the tray Part K & L.
Jx2
K
L

PRODUCT ASSEMBLY
07
08
08
Attach the ramp Part M by 2XP5 screws.
Put in the divider Part N.
P
5
X2
N
M

PRODUCT ASSEMBLY
09
09
Attach the roof Part O by 6XP5 screws.
P
5
X6
O

PRODUCT ASSEMBLY
10
10
Attach the roof hinge P6 by 4XP5 screws.
P
6
X
P
5
X
2
8
Finish

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.