aivituvin AIR 67 User manual

I
AIR 67
www.aivituvin.com
NSTRUCTION
MANUAL

Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure
every 90 days.
Fasten screws loosely during initial assembly. Do not
fully tighten screws until the item is completely
assembled.
Do not use or store this item in the proximity of open
flame or flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop
using this product until repairs are made and/or factory
replacement parts are installed.
Do not use this item in a way inconsistent with the
manufacturer’s instructions as this could void the
product warranty.
Please retain these instructions for future
NOTICE
01

02
PHILLIPS
SCREWDRIVER DRILL (RECOMMENDED) 2PERSON ASSEMBLY APPROXIMATELY 60MIN. ASSEMBLY
M6.0x55 mm BOLT
8PCS+1 spare
M3.5x60 mm SCREW
20PCS+1 spare
M3.5x40 mm SCREW
12PCS+1 spare
M3.5x35 mm SCREW
8PCS+1 spare
TOOLS REQUIRED
HARDWARE
P1 P2
P3 P4
P5
M3.5x25 mm SCREW
24PCS+1 spare
P5
P6
M3.0x16 mm SCREW
14PCS+1 spare
P6
P7
Lock
1PC
P6
P8
12PCS
Spacer

03
P9
Connect pieces
2PCS
HARDWARE

04
PARTS
ABC
D
EFGH
I
J
K
L
2PCS 1PC
1PC
Upper panel-front and back Down panel- Front side Down panel- Back side Side Panel
2PCS
1PC
2PCS
Tray
Casters with brake
3PCS
2PCS
2PCS
Casters without brake Perch
Left panel of nesting box
2PCS
Right panel of nesting box
2PCS
Front panel of nesting box
Bottom panel of nesting box
2PCS

05
PARTS
MNOP
QRS
2PCS
2PCS
2PCS
Divider Roof of nesting box Roof Roof cap
1PC
2PCS
1PC
PVC Waterproof Strip Ramp
1PC
Bottom plate
(Only need for connecting
with the coop AIR60)

PRODUCT ASSEMBLY
01
Attach Part A,B,C to the side panel Part D by P2x16; then connect the Part A to B&C
by P2x2.
06
B
D
P2 X16
A
D
C
A
A
P2 X2
D
DB
C
A

PRODUCT ASSEMBLY
①Insert the perches 3xPart H into the slots inside the front and back panel of coop.
② Slide in the tray.
02
07
Hx3
03
Screw two casters without brake Part E to the front of coop legs by P5x6 using the P8
spacer.
P8 X6
P5 X6
Fx2
P8 X6
P5 X6
Ex2
G
①
Screw two casters with brake Part F to the back of coop legs by P5x6 using the P8 spacer.②

PRODUCT ASSEMBLY
04
Attached the front panel of nesting box Part K by P3x4 on each side.
05
08
K
P1 X4
P3
K
Attach the side panels of nesting box Part I & J to the side of coop by bolt P1x4 on each side.
P1 X4
I
J
I
J
P1 X4
P1 X4
P3

PRODUCT ASSEMBLY
06
Attach the roof of nesting box 2xPart N to the nesting box by 4XP6 screws on each side.
Make sure the lock is functioning properly before locking the roof.
09
①
②
07
①Drop in the bottom panel of nesting box Part L.
②Slide in the divider Part M on each side .
M
L
L
M
P6 X4
N
N
P6 X4