aivituvin XZ7002 User manual

INSTRUCTION
MANUAL
XZ7002
www.aivituvin.com
X

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
P1 P2
P3 P4
P5
02
M3.5x40mm BOLT
M3.5x35mm SCREW
M3.5x50mm SCREW
8PCS+1spare
4PCS+1spare
8PCS+1spare
P6
4PCS+1spare
18PCS+1spare
M3.5x25mm SCREW
4PCS+1spare
M3.0x16mm SCREW
M3.0x16mm SCREW
P7 P8
2PCS
1PC
Latch

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
DEF
G
1PC
1PC 1PC
03
HI
1PC
1PC
1PC
1PC
1PC
Tray
Front panel
Back panel Right panel
Front panel of pen
Divider
1PC
Back panel of pen Side panel of pen Roof of pen

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
J K L
04
1PC
Roofs of hutch Roof cap Ramp
2PCS 1PC

PRODUCT ASSEMBLY
01
02
05
Attach the back panel Part B by 5xP2 screws.
①Attach Part A, C & D by 5xP2 screws.
②Pls notice the Divider Parts D attach on the left side.
P2X
5
A
B
C
D
P2X
5

PRODUCT ASSEMBLY
03
04
06
①Screw the ramp Part L to the left divider by 4xP5 screws as
show on the pictures.
②Slide in the tray Part E.
①Attach the pen !
②Attach Part H, F & G by 4xP2 screws.
P5
X4
G
P2
X4
L
H
E
F

PRODUCT ASSEMBLY
05
06
07
Attach the pen to the hutch from front by 2xP1 screws.
Attach the pen to the hutch from back by 2xP1screws.
P1X2
P1X2

PRODUCT ASSEMBLY
07
08
08
①Attach 2pcs of roof of hutch Part J to the hutch by 8xP3 screws.
②Attach roof of pen Part I to the pen by 4xP2 screws.
①Screw the roof cap Part K by 4xP4 screws.
②Screw the latch P6 by 4xP5 screws to connect top and side
panel of pen.
P5
X4
K
Jx2
P2X4
P3X8
I
P4
X4
P6X1
Finish here for only buying one coop

NOTICE
09
09
Take out side panel of pen Part H first of 1st hutch which you have
assembled according to the above steps.
H
①Pls ignore the following for only one coop owner !
②The below steps are the aeesmbly for the 2nd coop if you buying 2 coops !
③From step 9 to step 20 are assemble steps for 2nd coop !
④The assemble direction of the 2nd hutch Part D divider are difference with
1 st hutch, pls notice step 1 & 10 !

PRODUCT ASSEMBLY
10
11
10
①Attach Part A, C, & D by 5xP2 screws.
Attach Part B by 5xP2 screws.
P2X5
A
B
P2X5
②Pls notice the Divider Parts D attach on the right side.
(The direction of Part D is difference from 1st hutch)
C
D

PRODUCT ASSEMBLY
12
13
11
①Screw the ramp Part L to the right divider by 4xP5 screws as
show on the pictures.
②Slide in the tray Part E.
①Attach the pen !
②Attach Part H, F & G by 4xP2 screws.
E
P2X4
L
P5X4
H
F
G

PRODUCT ASSEMBLY
14
15
12
Attach the pen to the hutch from front by 2xP1 screws.
Attach the pen to the hutch from back by 2xP1 screws.
P1
X2
P1
X2

PRODUCT ASSEMBLY
16
17
13
①Attach 2pcs of roof of hutch Part J to the hutch by 8xP3 screws.
②Attach roof of pen Part I to the pen by 4xP2 screws.
Screw the roof cap Part K by 4xP4 screws.
Jx2
P3
X8
K
I
P4
X4
P2
X4

PRODUCT ASSEMBLY
18
19
14
①For this step, the previous latch need to be took out and rescrew
to the right position show as picture.
②Take out side panel of pen Part H from 2nd hutch.
Attach the second hutch to first hutch with 2xP7 from front by 4xP8
screws.
Change to
H
P7X2
P8

X4

PRODUCT ASSEMBLY
20
15
Attach the second hutch to first hutch with 2xP7 from back by 4xP8
screws.
P7X2
P8X4

HELP CENTER
[email protected]
Question about your product? we're here to help contact us via
Returns & Refunds
?
Product AssemblyOrders FAQProduct inquiry
THANK YOU
Thanks for your support to Aivituvin.
Your satisfaction is our #1 priority.
Once the items are received, opened, and deemed to be faulty
or other problems.
Pls contact us at [email protected] for the solution.
We will feedback to you within 24 hours.
If you are happy with the shopping ,welcome to share photos
and thoughts with others .
www.aivituvin.com
16

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.