aivituvin AIR 82 User manual

INSTRUCTION
MANUAL
AIR 82
www.aivituvin.com

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
120MIN. ASSEMBLY
HARDWARE
P1 P2
P3 P4
02
M6.0x50mm BOLT
M3.5x60mm SCREW
M6.0x60mm BOLT
36PCS+1spare
4PCS 6PCS
P5 P6
M3.5x45mm SCREW
60PCS+1spare
M3.5x35mm SCREW
30PCS+1spare
P7
M3.5x30mm SCREW
4PCS+1spare
M3.0x30mm SCREW
28PCS+1spare
P8
M3.0x14mm SCREW
24PCS+1spare

HARDWARE
P9 P10
P11
03
Latch
6PCS
Hook
2PCS
Eye hook
12PCS

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
04
BC
2PCS
E
1PC
Lower right panel of house
2PCS
Upper panel of house -
front & back
F
Lower panel of house -
front & back
2PCS
Layer
CARTON 1/3
J1
1PC
Right panel of chimney
J2
1PC
Left panel of chimney
K1
1PC
Front panel of chimney
K2
1PC
Back panel of chimney
L
1PC
Roof of chimney

A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
05
PARTS
Q
1PC
Right panel of run- 2nd floor
Y
2PCS
Bridge
Z
1PC
Waterproof Cover

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
06
G2
1PC
House roof- Right
H
1PC
Roof cap
I
1PC
Ramp
X
2PCS
Roof of run
A
1PC
Upper left panel of house
D
1PC
Upper right panel of house
G1
1PC
House roof- left
CARTON 2/3

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
07
CARTON 3/3
I
2PCS
Ramp
M1 M2
1PC
Front panel of run- 1st floor
1PC
Back panel of run- 1st floor
N
1PC
Left panel of run- 1st floor
O1 O2
4PCS
8PCS
Layer supporting bar Layer supporting bar with
dowel
P1
4PCS
Short Layer
P2
2PCS
Long Layer
R
1PC
Front panel of run- 2nd floor

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
08
CARTON 3/3
ST
1PC
Left panel of run- 2nd floor
1PC
Back panel of run- 2nd floor
U
1PC
Back panel of run- 3th floor
VW
1PC
2PCS
Front panel of run- 3th floor Left / Right panel of run-
3th floor

A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
09
Option 1
Option 2
From Step1-22 is for Optional 1
From Step23-35 is for Optional 2

PRODUCT ASSEMBLY
01
02
10
①
②Connect the Part B, C by 4xP4.
Attach the latch P9 by 4xP8.
①Connect the Part A, D and E by 8xP4.
②Attach the latch P9 by 4xP8.
B
P4
X4
B
C
P9
X1
P8
X4
E
D
P9
X1
P8
X4
E
A
P4
X8

PRODUCT ASSEMBLY
03
04
11
Put in 2pcs of the Layer Part F.
P3X6
B
Connect the lower panel Part B, C to the upper house by 6xp3.
C
Fx2

PRODUCT ASSEMBLY
05
06
12
Attach the roof G1, G2 to the house by 8xP5.
(Notice the eaves should keep in line with part A)
①Attach the roof cap Part H by 4xP6.
②Screw the ramp I by 2xP5.
G1
P5
X8
G2
P
6
X4
H
P
5
X2
I

PRODUCT ASSEMBLY
07
13
08
①Connect the Part K2, J1, J2 by 4xP5.
②Screw the chimney to the roof by 4xP5.
③Connect Part K1 to the chimney by 4xP5.
①Attach the roof Part L by 4xP5 to complete the chimney.
②Attach the ramp Part I by 2xP5 on each side.
From Step 9-10 is the assemble for 1st floor of the run.
J1
P5
X4
J2
K2
P5
X4
P5
X4
K1
P
5
X4
P
5
X2
I
P
5
X2
I
L

PRODUCT ASSEMBLY
09
14
①Connect the Part M1, M2 and N by 4xP4.
②Attach the latch P9 by 4xP8 on each position.
③Attach O1 to Part M1 by 2xP1, Attach the other O1 by 2xP2.
④Attach O2 to Part N by 2xP4 on each side.
10
Attach the Long layer P2 to the shelf of Part M1, Short layer P1 to to the
shelf of Part N by 8xP7.
From Step 11-13 is the assemble for 2nd floor of the run.
P4
X4
P9
X2
P8
X8
P1
X2
O1x2
O2x2
P4
X4
M1 M2
N
P
2
X2
P
7
X8
P2
P1

PRODUCT ASSEMBLY
11
15
①Connect the second floor of the run Part Q, R, S, W by 8xP4.
②Attach the latch P9 by 4xP8 on each position.
12
①Attach Part O1 to Part S by 2xP2 on each side.
②Attach Part O2 to Part T by 2xP4 on each side.
P9
X2
P8
X8
P4
X8
QR
SW
P2
X4
P4
X4
O1x2 O2x2

PRODUCT ASSEMBLY
13
16
Attach the Long layer P2 to the shelf of Part S, Short layer P1 to the shelf
of Part T by 8xP7.
14
Connect the 1st floor with the 2nd floor by 7xP3.
From Step 15-18 is the assemble for 3rd floor of the run.
P2
P1
P
7
X8
P
3
X7
S
TR
Q
Q
S
R
T
N
M1

PRODUCT ASSEMBLY
15
17
Connect Part U,V,T by 8xP4.
16
Attach the layer supporting bar O2 by 8xP4.
P4
X8
U
V
W
T
P
4
X8
O2x4
W
W
U
V

PRODUCT ASSEMBLY
17
18
Attach the short layer P1 by 8xP7.
18
①Attach Part X to complete the 3rd floor of the run by 12xP4.
②Connect two Part X together by 3xP3.
P
7
X8
P1x2
P
4
X12
Xx2
P
3
X3
Z
③Cover the Part Zto the top of the run, there are hooks on Part Zto
connect with the mesh.