aivituvin AIR06-B User manual

INSTRUCTION
MANUAL
AIR06-B
www.aivituvin.com
X

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
P1 P2
P3 P4
P5
02
M3.5x35mm SCREW
M3.5x25mm SCREW
M3.5x45mm SCREW
20PCS+1spare
8PCS+1spare
16PCS+1spare
P6
12PCS+1spare
M3.0x20mm SCREW
4PCS+1spare
M3.0x16mm SCREW
2PCS
Roof hinge
P7
1PCS
Chewing toy
P8
2PCS+1spare
M4.0x20mm SCREW

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
D E F
G
1PC
1PC 1PC
03
HI
1PC
2PCS
1PC
1PC
1PC Back panel of down area
Left side panel
Right side panel Front panel of upper area
Tray supporting bars
Front panel of down area
1PC
Divider Back panel of upper area Roof

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
J K L
M N O
P
1PC
1PC 1PC
04
QR
1PC
1PC
1PC Front board of feeder
Ramp
Left piece of feeder
Bottom tray
Right piece of feeder
2PCS
Casters without brake Brake casters
1PC
Tray
2PCS
Metal ramp supporting

A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
05
PRODUCT ASSEMBLY
Upper Area
Down Area

PRODUCT ASSEMBLY
01
02
06
Attach two side panel Part A and Part B to the whole back panel
by P2x10.
①Attach back panel up Part H and down Part E by P4x4.
②Screw the ramp suppor Part R to the down Part E by P8x2
according to the predrill screw holes.
P4X
4
P2X
10
A
B
H
R
E
P8X
2

PRODUCT ASSEMBLY
03
04
07
Attach the wooden feeder Part L, M and Part N by P3x4.
Screw the wooden feeder into Part C from inner by P2x2.
P3
X4
N
P2
X2
L
M
C

PRODUCT ASSEMBLY
05
06
08
Attach the front panels Part C and Part D to the sides by P1x8.
Put down supporting bars 2pcs of Part F.
Fx2
D
C
P
1
X8

PRODUCT ASSEMBLY
07
08
09
Screw the ramp Part J to the supporting bars by P5x2.
Slide in the middle tray Part K and bottom tray Part O.
O
P
5
X2
K
J

PRODUCT ASSEMBLY
09
10
10
①Put in the divider Part G as show on picture.
②Put in the chewing toy P7 in the cage wherver you want.
Screw two casters without brake Part P to the front of hutch legs
by P3x4 each.
P3
X8
Px2
P
7
X1
G

PRODUCT ASSEMBLY
11
12
11
Screw two brake casters Part Q to the back of hutch legs by
P3x4 each.
Attach the roof Part I to the back panel of hutch by P5x6.
Qx2
P
3
X8
I
P
5
X6

PRODUCT ASSEMBLY
13
12
Screw the roof hinge P6 to connect the roof and side panel by
P5x4 each side.
P
6
X
P
5
X
1
4
P
6
X
P
5
X
1
4
Finish

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.