aivituvin AIR20-B User manual

INSTRUCTION
MANUAL
AIR20-B
www.aivituvin.com

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
Do not use this item in a way inconsistent with the
manufacturer’ s instructions as this could void the product
warranty.
01

PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
8PCS+ +1spare
P1 P2
P3
02
M3.5x35mm SCREW
18PCS++1spare
M3.0x16mm SCREW
12PCS spare
M3.5x45mm SCREW
P4
2PCS ++1spare
M3.0x10mm SCREW
2PCS+
P5 P6
Latch
1PC
Eye hook
P7
1PC
Chewing Toy for Gift
TOOLS REQUIRED
HARDWERE

A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
DEF
G
1 PC
1 PC
03
HI
1 PC 1 PC
1 PC
1 PC
1 PC
Right Panel
1 PC Sliding Tray
Front Panel Back Panel Left Panel
Top Cover Panel
Ramp Layer Divider
1 PC
PARTS

A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
J K L
MN
2 PCS
Casters without brake
04
2 PCS
1 PC
Wood Floor
1 PC Brake Casters
Bootom Wire Netting Extra Hutch Legs
(Optional)
4 PCs
O
Folding Metal feeder
1 PCS
P
Wood shelf
1 PC
PARTS

PRODUCT ASSEMBLY
05
OPTIONAL- HUTCH ON
THE GROUND
Follow the step from step 1 to
step 10 to finish!
OPTIONAL- HUTCH WITH
4 HIGH LEGS.
Follow the step from step 1 to
step 8,skip the Step9 & Step
10,then go on until the last step
to finish!

PRODUCT ASSEMBLY
01
02
06
Attach Part A, Part C and Part D by 4xP1 screws. And then attach
divider Part I to Part A by 2xP1 screws.
Attach back panel Part B by 4xp1 screws.And Screw another side of
divider to the back by 2xP1 screws.
C
P1 X6
I
D
A
P1 X6
B

PRODUCT ASSEMBLY
03
04
07
Slide in the tray Part E.
①Put inside the bottom wire netting PART M to be UPWARDS,

M
E
P
J
to seperate the urine & poop.
Put inside the wood floor Part J as show on the picture.
Put inside the wood shelf Part P as show on the picture.
②
③

PRODUCT ASSEMBLY
05
0 6
08
Attach the top cover panel Part F to the house by 6xP3 screws.
①Screw the ramp Part G to the upper frame of divider Part I by 4xP3.
HP7
G
F
P3 X4
P3 X6
Put the layer Part H above the divider,it can be removable freely to
catch the pets.
②
③Put the chewing toy P7 inside the cage anywhere you want.

PRODUCT ASSEMBLY
07
08
09
Screw latch P6 to the Part C by 4XP3 screws as show on picture.
①Screw the folding metal feeder Part O to the inside of Part D by
2xP4 screws.
O
P4 X2
P5 X1
P6 X1
P3 X4 P6 X1
P3 X4
②Screw the eye hook P5 to the Part C, tie the rope on one side of
roof ,the other side of hook to make the roof open.
①
②Screw latch P6 by 4xP3 screws to connect the top and front panels.

PRODUCT ASSEMBLY
10
Below steps are optional:
If you want to put the the hutch on the ground,
followthe Step 9,Step 10 to finish!
If you want to make the hutch with 4 higher legs,
just skip Step 9 ,Step 10 and go on Step 11 to
Step 14 to finish.
09
Screw two brake casters Part K to the back of hutch legs.

K
K

PRODUCT ASSEMBLY
10
11
Screw two casters without brake Part L to the front of hutch legs.
Attach the extra high legs Part N to the front by 2xP2 screws each
side.
11
N
N
L
L
P2 X2
P2 X2

PRODUCT ASSEMBLY
12
13
Attach the extra high legs Part N to the back by 2xP2 screws each
side.
Screw two brake casters Part K to the back of hutch legs.
12
P2 X2
P2 X2
K
K
N
N

PRODUCT ASSEMBLY
14
Screw two casters without brake Part L to the front of hutch legs.
L
L
13

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.