aivituvin AIR 26 User manual

INSTRUCTION
MANUAL
AIR 26
www.aivituvin.com
X

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
45MIN. ASSEMBLY
HARDWARE
24PCS+1spare
P1 P2
P3 P4
P5
02
M3.0x25mm SCREW
M3.0x16mm SCREW
M3.5x40mm SCREW
M3.0x10mm SCREW
6PCS+1 spare
6PCS+1 spare
8PCS+1spare
Eye hook
1PC
P6
Chewing Toy
1PC

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
DEF
G
1PC
1PC 1PC
03
HI
3PCS
1PC
1PC
1PC
1PC
Front panel Back panel Left side panel
Roof
Right side panel
Down layer
1PC Ramp
Drawer
Upper layer

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
J K L
M
04
2PCS
2PCS
Front panel of small house
Seeasw
4PCS 2PCS
N O
1PC
Base of seesaw
2PCS
P
1PC
Bowl
Side panels of small house Roof of small house
Base of bowl

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
05

PRODUCT ASSEMBLY
01
02
06
Screw the ramp Part I to the layer Part G by 2xP4.
①Attach the front panel Part K,the roof panel Part L to the side
panels Part J by 10xP2 to finish the small house.
②Repeat the same way for the second one.
P2X
10
I
Jx2
P4X2
G
K
L

PRODUCT ASSEMBLY
03
04
07
Screw the ramps Part I to the layer Part H by 4xP4.
Complete the two sessaws by 2xP2 each.
P4
X4
Ix2
M
H
N
P2
X2

PRODUCT ASSEMBLY
05
06
08
①Attach the side panels Part C & D to the front panel Part A by
4xP1.
①Attach the back panels Part B to the side panels by 4xP1.
C
P1X4
P1X4
B
②Notice to align with the dowels.
A
D
②Notice to align with the dowels.

PRODUCT ASSEMBLY
07
08
09
Slide in the tray Part E.
Put the down layer to the slot of back & side panel.
E

PRODUCT ASSEMBLY
09
10
10
Put the small houses to the layers.
Put the upper layer to the slot of back & side panel.

PRODUCT ASSEMBLY
11
12
11
Put the chewing toy P6 and bowl Part O & P into the cage.
Put the seesaw into the cage.
P
O
P6X1

PRODUCT ASSEMBLY
13
14
12
①Attach the hook eye to left side panel.
Attach the roof Part F to the back panel by 6xP3.
P5X1
F
P3X6
②Tie the rope to the eye hook.

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.