Axor Starck 10929007 Manual

INSTALLATION
ZH ⁄ 用户手册 ⁄ 组装说明 02
EN ⁄ Instructions for use ⁄ assembly instructions 03
AXOR Starck
10929007

02
安全技巧
装配时为避免挤压和切割受伤，必须戴上手套。
本产品只允许作为洗浴、卫生和洁身之用。
头顶花洒应当安装到天花板上，天花板必须有足
够的承重能力。
钻孔时请注意电线和水管！
安装提示
⁄ 安装前必须检查产品是否受到运输损害。 安装后
将不认可运输损害或表面损伤。
⁄ 管道和阀门必须根据通用标准进行安装、冲洗和
检查。
⁄ 请遵守当地国家现行的安装规定。
⁄ 仅可使用合适的紧固材料！附带的螺丝和木钉仅
适用于混凝土。
技术参数
工作压强： 最大 0,6 MPa
推荐工作压强： 0,2 - 0,4 MPa
(1 MPa = 10 bar = 147 PSI)
热水温度： 最大 60°C
热力消毒: 最大 70°C ⁄ 4 分钟
该产品专为饮用水设计！
备用零件(参见第页 14)
安装(参见第页04)
大小(参见第页 13)
清洗(参见第页 08)
请勿使用含有乙酸的硅胶！
符号说明
流量示意图(参见第页 13)
ZH

03
SAFETY NOTES
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The product may only be used for bathing, hygienic
and body cleaning purposes.
The ceiling to which the overhead shower is to
mounted must have sufficient bearing capacity.
Observe all current and water lines when drilling!
INSTALLATION INSTRUCTIONS
⁄ Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
⁄ The pipes and the fixture must be installed, flushed and
tested as per the applicable standards.
⁄ The plumbing codes applicable in the respective coun-
tries must be observed.
⁄ Only suitable fastening material may be used! The en-
closed screws and plugs are only suitable for concrete.
TECHNICAL DATA
Operating pressure: max. 0,6 MPa
Recommended operating pressure: 0,2 - 0,4 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 60°C
Thermal disinfection: max. 70°C ⁄ 4 min
The product is exclusively designed for drinking water!
SPARE PARTS (see page 14)
ASSEMBLY (see page 04)
DIMENSIONS (see page 13)
CLEANING (see page 08)
Do not use silicone containing acetic acid!
SYMBOL DESCRIPTION
FLOW DIAGRAM (see page 13)
EN

04
2
3 4
6
5
1
19 - 24 mm
1. 2.
Montage Montage

05
7
Ø 8 mm
SW 8 mm
11
8
910
12
SW 10 mm
19 - 24 mm
1.
1.
1. 2.
2.
2.
3.
Montage

06
13
16
17
SW 4mm
14
15
18
SW 4 mm
(2 Nm)
SW 8 mm
(10 Nm)
1.
2.
Montage

07
click
21
23
22
20
24
19
Montage

08
重要说明
肥皂，洗发水、沐浴液、染发剂、香水、刮胡水、指甲油
的残留也会对产品造成损伤。
此 处 ：使 用 后 要 小 心 地 用 清 水 将 剩 余 物 冲 洗 干 净 。
同样在产品下方不得存放洗涤剂和化学药品，例如不
可放在用于洗脸盆的梳洗柜中否则挥发气体将损坏
产品。
在已经损伤的表面继续使用清洁剂会给表面造成更大
的损伤。
表面损坏的部件必须更换，否则会有受伤的
危险。
不按规定进行清洁而造成的任何损坏不在本公司产品
保修范围之内。
QUICKCLEAN
有了QuickClean，手工清洁功能，要去掉喷头上的水
垢 ，只 需 简 单 地 搓 除 即 可 。 
担保
Hansgrohe 向用户保证，该产品无制造 缺陷。
如果自购买之日起五年内出现缺 陷，Hansgrohe
将免费排除。 保证条件和详 情见
www.hansgrohe-int.com⁄guarantee。 在提 出保修的权
利时请联系您的合同方。本保证 不涉及有关国家法律
规定的消费权
汉斯格雅产品的清洁建议
现代的卫浴龙头、厨房龙头、花洒、配件、盥洗台、浴盆
和加热器采用的制造材料非常迥异，以适应产品外形
设计和使用功能的市场需求。
为 了 避 免 产 品 损 坏 和 由 此 引 发 的 投 诉 及 争 议 ，必 须 在
使用和清洁产品时遵循有关规程。
在保养汉斯格雅产品时，原则上必须注
意：
⁄只能使用那些有明确注明是适用于本产品的清洁
剂。
⁄不允许使用含有盐酸、蚁酸、氯漂或醋酸的清洁
剂，因为这些清洁剂会给产品表面造成严重的损
伤。
⁄含磷酸的清洁剂必须在特定条件下使用。
⁄不允许将两种以上清洁剂混合使用。
⁄不允许使用具有研磨 作 用 的 清 洁 工 具 和 设 备 ，如 不
适合的清洁粉末、海绵垫或超细麦克布。
⁄必须严格遵守清洁剂生产厂商的使用说明。
⁄严格遵守清洁剂的用量和作用时间，决不允许清洁
剂的作用时间长于规定值。
⁄定期的清洁以预防水垢。
⁄不允许将清洁剂直接喷射到汉斯格雅产品上，因为
喷雾会进入汉斯格雅产品的开口部分和缝隙中而
造成损害。首先将清洁剂喷在软布上，再用软布进
行清洁。
⁄清洁之后必须用足够的清水冲洗，以彻底去除残留
的 吸 附 物（ 清 洁 剂 ）。
⁄不允许使用蒸汽清洗机，高温会损害产品。
QUICK
CLEAN
Reinigung

09
⁄ After cleaning rinse thoroughly with clean water to
remove any cleaner residue.
⁄ The use of steam cleaners is not permitted. The high
temperatures can damage the products.
IMPORTANT
Residues of toiletries such as liquid soaps, shampoos and
shower gels, hair dyes, perfumes, aftershave and nail
varnish can also cause damage.
Here too: Carefully rinse with water after use to remove residues.
Likewise, do not store any cleaning agents or chemicals
under the products, for example in a vanity unit, as the
vapours may damage the products.
The damage of already damaged surfaces will deteriorate
under the effect of the cleansers.
COMPONENTS WITH DAMAGED SURFACES
MUST BE EXCHANGED, OTHERWISE THERE
COULD BE AN INJURY DANGER.
Damage caused by improper treatment will not be covered
by our guarantee.
QUICKCLEAN
The QuickClean cleaning function only needs a small
manual rub over to remove the lime scale from the spray
channels.
WARRANTY
Hansgrohe guarantees to the consumer that this product is free
of production faults. If evertheless any defect is detected within 5
years from date of purchase, Hansgrohe will remedy this defect
free of charge. You will find the conditions and details of this
guarantee at www.hansgrohe-int.com⁄guarantee. Please contact
your contracting party to claim your rights under this guarantee.
This guarantee does not affect the customer‘s rights under the
respective national legislation.
CLEANING RECOMMENDATION FOR
HANSGROHE PRODUCTS
Today, modern sanitary and kitchen tapware, showers,
accessories, washstands, tubs and radiators consist of very
different materials to comply with the needs of the market
with regard to design and functionality.
To avoid damage and reclamations, it is necessary to
consider certain criteria when cleaning.
WITH REGARD TO CARING FOR
THE HANSGROHE PRODUCTS, THE
FOLLOWING MUST IN PRINCIPLE BE
HEEDED:
⁄ Only use cleaning material which is explicitly provided
for this type of application.
⁄ Never use cleaning materials, which contain
hydrochloric acid, formic acid, chlorine pale lye or
acetic acid, as they cause considerable damage.
⁄ Phosphorus acidic cleaners are only conditionally applicable.
⁄ Mixing cleaning agents is not permitted, generally.
⁄ Never use cleaning materials or appliances with an
abrasive effect, such as unsuitable cleaning powders,
sponge pads or micro fibre cloths.
⁄ The instructions of the cleaning agent manufacturers
have to be followed absolutely.
⁄ Cleaning has to be carried out with a specified cleaner dosage,
contact time, object-related and adapted to the needs.
⁄ The building up of calcifications has to be removed by
cleaning regulary.
⁄ When using spray cleaners, spray the cleaning solution onto
a soft cloth or sponge, never directly onto the Hansgrohe
products, as the atomised spray could enter openings and
gaps in the Hansgrohe products and cause damage.
QUICK
CLEAN
Reinigung

10
1
4
5
2
3
SW 4mm
6

11
SW 4 mm
(2 Nm)
9
11
10
78
1.
1.
2.
3.
2.
12
Reinigung

12
click
14
15
13
Reinigung

13
bar
4,5
0,0
0,5
1,0
1,5
2,0
2,5
3,0
3,5
4,0
5,0
0,45
0,00
0,05
0,10
0,15
0,20
0,25
0,30
0,35
0,40
0,50
5,50,55
6,00,60
036912151821242730
MPa
00,1 0,2 0,3 0,4 0,5
Q = l/min
Q = l/sec
R1/2
Maße ⁄ Durchflussdiagramm
AXOR Starck
10929007
AXOR Starck
10929007

14
(M6x12)
SW 4 mm
95802007
97735000
98127000
(11x 2 )
98129000
(14x2)
98156000
(36x2)
98408000
(130x2,5)
95888000
95887000
95889000
95890000
AXOR Starck
10929007
Serviceteile Serviceteile

15

AXOR ⁄ Hansgrohe SE
Auestraße 5–9
77761 Schiltach
Deutschland
[e-mail]
axor-design.com 11 ⁄ 2 0 18 9.01713. 51