B. Braun Aesculap Challenger Ti-P User manual

Aesculap®Challenger®Ti-P
Aesculap AG | Am Aesculap-Platz | 78532 Tuttlingen | Germany
Phone [phone] | Fax [phone] | www.aesculap.com
Aesculap – a B. Braun company
All rights reserved. Technical alterations are
possible. This leaflet may be used in no way
whatsoever other than for the offering, buying
and selling of our products.
No part may be copied or reproduced in any
form. In the case of misuse we retain the right
to recall our catalogues and pricelists and to
take legal action.
The main product mark Aesculap and the
product mark Challenger Ti-P are registered
marks of Aesculap AG.
Brochure No. C62402 0510/1.0/2
Aesculap Endoscopic Technology
Disassembly and assembly instructions
C62402 0510-1-2.qxd:Layout 1 10.05.2010 18:07 Uhr Seite 1

4. Hold instrument shaft. Pull back star wheel to disengage the safety ring and to release
instrument shaft. Remove safety ring from handle.
DISASSEMBLY CARE ASSEMBLY
STERILE REPROCESSING & ACCESSORIES
FUNCTION CONTROL
Reprocess the product immediately after use.
For advice on cleaning, disinfection and sterilization, please follow the
instructions for use.
The product can be sterilized either in disassembled or in assembled condition.
For the latest information on reprocessing, please also refer to the Aesculap
Extranet via www.aesculap-extra.net.
For accessories and spare parts, please refer to brochure C623 or visit
www.endoscopy-catalog.com.
Assemble handle and complete shaft together. Press the lever of the handle as far as it will go and
release it again.
Closing of the jaw part. The tips of the jaw part have to touch each other and have to close parallel.
The tips may not cross each other (scissoring effect).
Check push rod regarding breakages and bendings.
If necessary exchange components or return the instrument for repair.
To avoid damages of jaw parts
during transportation and reproces-
sing make use of the jaw part
protection cap.
REPAIRS
In order to ensure the preservation of full guarantee and warranty rights, only persons authorized
by Aesculap may carry out repairs. Please send products for repair to:
Aesculap Technical Service, Am Aesculap-Platz, D-78532 Tuttlingen, Germany.
Additional service addresses may be obtained from the same address or via [email protected].
CO2cylinder
Safety ring
Protection cap
Star wheel
Lever
Push rod
Inner tube
Outer shaft Clip cartridge
Aesculap®Challenger®Ti-P Aesculap Endoscopic Technology
1. If cartridge is still assembled, press jaws
together by pushing lever. Pull off cartridge
and discard it.
1. Check push rod regarding breakages
and bendings. Insert push rod into
inner tube.
6. Pull push rod out of inner tube.
2. Remove CO2cylinder from handle.
a
b
3. Rotate safety ring so that the opening is
pointing to the lever.
5. Pull inner tube out of outer shaft.
For smooth running of the instrument, lubricate all moving parts and joints
of the shaft with a steam-permeable lubricant (e.g. Aesculap STERILIT®I oil
spray JG600). After lubrication of the shaft please open and close the jaw
part several times by pushing the lever of the handle.
No lubrication of the whole handle
4. Attach safety ring on the handle
between star wheel and lever.
3. Pull star wheel back and insert shaft.
Marking on star wheel and marking on
shaft should line up.
2. Insert inner tube and push rod into outer shaft.
5. Rotate safety ring 180°. The ring opening
should be pointing up.
C62402 0510-1-2.qxd:Layout 1 10.05.2010 18:07 Uhr Seite 2