FRENCH FITNESS FF-X9LP User manual

FF-X9LP
ASSEMBLY MANUAL
Functional Multi Gym System w/Leg Press

FEATURES
•
•
•
•
with ease
•
bearings
•
TECH SPECS
•190 lb Weight Stack
•Lat Pulldown: Feels like 280 lbs Due to pulley ratio
•Dimensions: 82"D x 91 "W x 83.9"H
WARRANTY
• Lifetime Parts and 1 Year Labor Warranty
2

NO
Name
QTY
NO
Name
QTY
1
Under Frame
43
Incline support Pollex Frame
2
Guide Road
44
M 12x75 outer hex bolt
3
Rubber Cushion
45
Pedal Board
4
ФWashers
46
M 10x85 outer hex bolt
5
M10x20 outer hex bolt
47
Pulley
7
M8x50 outer hex bolt
48
Pulley Spacer
8
Flat washers
49
Steel wire rope
9
M8 Lock nuts
50
M 10x45 outer hex bolt
10
Lifting Rod
51
M 10x130 outer hex bolt
11
Top Plate
52
M 12x85 outer hex bolt
12
Cuts Iron Cooler Weight
54
Pulley weldment
13
Magnetic Pin
55
Transition Rope
14
Inclined Support beam
56
Link Chain
15
Adjustment boars
57
Butterfly arm Rope
16
Reset Poll Pin
58
M 10x15 outer hex bolt
17
Ф12 Flat Washers
59
Backrest adjusting Board
18
M 12 Lock nuts
60
Cushion
19
M 12x70 hex bolts
61
Backrest tube Shaft
20
Upper beam
64
Foam tube
21
M 10x70 outer hex bolt
65
Foam Rod
23
M 10x60 hex bolts
66
Foam
24
Shield support frame
67
Inner end cup
25
M 10 lock nuts
68
Outer end cup
26
Decorative board
70
Shrauds
27
M 12x130 outer hex bolt
71
M 8x16 outer hex bolt
28
Seat supporting tube
72
Straight bar
29
Seat cushion adjustment tube
73
Lat bar
30
Kick rotation shaft
74
Hex reset poll pin
31
Foot hook bending tube
101
Poll strap
32
Pushing frame
103
Support board Left/Right
33
Front pushing arm
104
Low poll steel rope
34
Ф16x137 Front connection shaft
105
Flat pedal chasis
35
Reset poll pin
106
Metallurgy sleeves
36
17x123 Pushing frame shaft
107
Seat cushion Board
38
Ф10x30 Washers
108
Backrest adjusting tube
39
M 10x16 outer hex bolt
109
Ф25x112 Shaft
40
M 12x20 outer hex bolt
110
Movable tube
41
Butterfly arm Left
120
M 10x35 outer hex bolt
42
Butterfly arm Right
121
10x30 Flat washers
122
Leg press board
3

Parts Diagram
10 20
1
2
103
35 7224
14
29
30 28
41 42 32
33
3436
41
43 45 45 28
48 56 73 72
43 101
60
65 66
107 106
70
31
64
11 12
26
10
54 59
105 109
4

Parts Diagram
39
58 71
40
417
75
27
46
52
50
120
51
19
44
9
21
18
23
67 68
13 47 49 55 57
5

Install i n g S tep 1 Exploded View
4
2
3
4
5
1
6

Installation Instruction
1. Put Φ10 washer (4) over M10*20 outer hexagonal bolts (5), and fasten the guiding
rod assembly (2) to the underframe weldment (1).
2. Install the cushion (3) on the guiding rod assembly (2)
Note: The outer hexagonal bolts need to be tightened
7

Installing Step 2 Exploded View
10
2
11
12
11
13
8

Install ing Step 2After Installation
Installation Instruction
1. Place 11 PCS cast iron counterweight lowerpiece (12) and cast iron counterweight top piece (11)
in sequence on the upper end of the guiding rod assembly (2).
2. Insert the lifting rod (10) and the cast iron counterweight lower piece (12)and the cast iron
counterweight top piece (11) together, and install the positioning bolts on the cast iron
counterweight top piece (11).
3. Insert the magnetic pin (13) on the cast iron counterweight lower piece (12) and
the lifting rod (10).
4. Fasten the counterweight limit block (6) to the guiding rod assembly with M8*50 outer
hexagonal bolts (7), at washers (8), and M8 lock nuts (9).
Note: The outer hexagonal bolts need to be tightened.
9

Installing Step 3 Exploded View
14 40
17
17
15
15
18 18
17
19
17
17
16
10

Installing Step 3After Installation
Installation Instruction
1. Fasten the inclined support beam (14) to the chassis assembly with 12*70 outer
hexagonal bolts (19), 12 at washers (17), and M12 lock nuts (18).
2. Use 12*20 outer hexagonal bolts (40) and 12 at washers (17) to x the inclined
support beam adjustment board (15).
3. Fix the reset pull pin (16) on the inclined support beam adjustment board (15).
Note: The outer hexagonal bolts need to be tightened
11

Install ing Step 4 Exploded View
13
14
23
23
17
17
24
17
18
20
14
5
19
12

4
Installation Instruction
1. Fix the shield suppor tframe (24) and the upper beam (20) together with M10*60
outer hexagonal bolts (23), Φ10 washers (4) and M10 lock nuts (25)
2. Connect the upper beam (20) and the guiding rod (2) together, and fasten them
with M10*20 outer hexagonal bolts (5), Φ10 washers (4) M10 lock nuts (25).
3. Fasten the upper beam (20) to the inclined support beam (14) with M12*70 outer
hexagonal bolts (19), M2 washers (17), and M12 lock nuts (18)
Note: The outer hexagonal bolts need to be tightened
13

Installing S tep 5 Exploded View
16
15
18
17
17
27
17
26
26
17
14

Installing Step 5After Installation
Installation Instruction
1. Use M12*130 outer hexagonal bolts (27), Φ12 washers (17) and M12 lock nuts(18)
to fasten the decorative board (26) to the upper beam and theinclined support
beam assembly.
Note: The hexagon bolt sneed to be tightened
15

Installing Step 6 Exploded View
17
20
18
19
29
30
72
5
4
31
28
4
17
5
19
18
16

Installing Step 6After Installation
Installation Instruction
1. Use M12*70 outer hexagonal bolts (19),Φ12 washers (17) and M12 lock nuts (18) to fasten the
seat supporting tube assembly (28) to the lower hole of the incluned support beam
2. Install the kick rotation shaft (30) on the foot hook bending tube (31), andthen connect the foot
hook bending tube (31) and the seat supporting tube assembly (28) together, and fasten them
on both ends of the kicking shaft (30) using M10*20 outer hexagonal bolts (5) and
Φ10 washers (4)
3. Install the seat cushion adjustment tube (29) on the seat supporting tube (28) and tighten it
with the hexagonal reset pull pin (72)
Note: The outer hexagonal bolts need to be tightened
17

Installing Step 7 Exploded View
32
36
37
38
22
35
33
34
18

Installing Step 7After Installation
Installation Instruction
1. Use the 17*123 front pushing frames shaft (36) to connect the front pushing frame (32) and the
decorative board (26) together, and fasten it to both ends of the front pushing frames haft (36)
with M10*20 outer hexagonal bolts (5) and Φ10*Φ30 washers (38).
2. Connect the front pushing arm (33) and the front pushing frame (32) together with the Φ6*137
front pushing arm connection shaft (34), and fasten it on both ends of the front pushing arm
connection shaft (34) with M12*20 outer hexagonal bolts (40) and Φ12 at washers (17).
3. Connect the reset pull pin (35) and the front pushing frame (32) together.
Note: The outer hexagonal bolts need to be tightened.
19

Installing Step 8 Exploded View
41 39
38
42
43
18
17
46
4
4
44 17
25
45
20