iPECS eMG80 User manual

iPECS eMG80
System DECT Installation Guide
Please read this manual carefully before operating System.
Retain it for future reference.

iPECS eMG80
System DECT Installation Guide Issue 1.3
Regulatory Information
Before making connections to the telephone network, you may be required to notify your local
serving telephone company of your intention to use "customer provided equipment.” You may
further be required to provide any or all of the following information:
PSTN line Telephone numbers to be connected to the system
Model name iPECS eMG80 DECT
The required regulatory agency registration number is available from your local Ericsson-LG
Enterprise representative.
This equipment complies with the following regulatory standards, EN 301, EN 406, TBR 10 and
TBR 22. Also, this equipment complies with the safety requirements of EN 60950-1 and the EMC
requirements of EN5022, EN5024, EN301 489-1 and EN 301 489-6.
GDC-450/500H has been designed to comply with the Hearing Aid Compatibility requirements as
defined in Section 68.316 of Part 68 FCC Rules.
If the telephone company determines that customer provided equipment is faulty and may
possibly cause harm or interruption in service to the telephone network, it should be disconnected
until repair can be affected. If this is not done, the telephone company may temporarily
disconnect your service.
The local telephone company may make changes in its communications facilities or procedures.
If these changes could reasonably be expected to affect the use of iPECS eMG80 or compatibility
with the network, the telephone company is required to give advanced written notice to the user,
allowing the user to take appropriate steps to maintain telephone service.
iPECS eMG80 complies with rules regarding radiation and radio frequency emission as defined
by local regulatory agencies. In accordance with these agencies, you may be required to provide
information such as the following to the end user:
WARNING
“This equipment generates and uses R.F. energy, and if not installed and used in
accordance with the Instruction Manual, it may cause interference to radio
communications. It has been tested and found to comply with the appropriate limits for a
telecommunication device. The limits are designed to provide reasonable protection
against such interference, when operated in a commercial environment. Operation of this
equipment in a residential area could cause interference, in which case the user, at his
own expense, will be required to take whatever measures may be required to correct the
interference.”

iPECS eMG80
System DECT Installation Guide Issue 1.3
Revision History
Copyright© 2013 Ericsson-LG Enterprise Co., Ltd. All Rights Reserved
This material is copyrighted by Ericsson-LG Enterprise Co., Ltd. (Ericsson-LG Enterprise). Any
unauthorized reproductions, use or disclosure of this material, or any part thereof, is strictly prohibited
and is a violation of Copyright Laws. Ericsson-LG Enterprise reserves the right to make changes in
specifications at any time without notice. The information furnished by Ericsson-LG Enterprise in this
material is believed to be accurate and reliable, but is not warranted to be true in all cases. If you are not
the intended recipient, you should destroy or retrieve this material to Ericsson-LG Enterprise.
iPECS is trademark of Ericsson-LG Enterprise Co., Ltd.
All other brand and product names are trademarks or registered trademarks of their respective companies.
SW version ISSUE DATE DESCRIPTION OF CHANGES
1.0.x
1.0
Sep., 2013
Initial Release
1.1.x 1.1 Dec., 2013 Changed Ericsson-LG to Ericsson-LG Enterprise
1.2.x
1.2
June, 2015
Changed LG logotype
2.0.x 1.3 Jan., 2016 Added GDC-480H and corrected the wrong operation in
subscription andAttendant service

iPECS eMG80
System DECT Installation Guide Issue 1.3
i
Table of Contents
1. Introduction .........................................................................1
2. System DECT Components & Specifications.....................2
2.1 General Specifications..................................................................3
2.2 WTIB4 Specifications ....................................................................3
2.3 GDC-600BE Specifications ...........................................................3
2.4 GDC-450H/480H/500H Specifications...........................................4
3. Installation...........................................................................5
3.1 Installation Overview.....................................................................5
3.2 Site Planning for Base Stations....................................................5
3.2.1 Cell-coverage Region Survey (CRS) ......................................................5
3.2.2 Preliminary Positions of Base Stations....................................................6
3.2.3 General Procedure for CRS....................................................................9
3.2.3.1 Additional Tips for CRS......................................................................10
3.2.4 Base Station General Guidelines..........................................................11
3.3 WTIB4............................................................................................14
3.3.1 Pin Assignment ....................................................................................15
3.3.2 Connectors, Switch and LED Functions................................................ 15
3.4 Description and Installation of GDC-600BE ..............................17
3.4.1 GDC-600E Description.........................................................................17
3.4.2 Base Station Installation.......................................................................17
3.4.2.1 Mounting Base Station.......................................................................18
3.4.2.2 Mounting Base Station - 2 (Using Wedge)..........................................19
3.4.2.3 LED Indications .................................................................................20
3.4.2.4 Traffic Guidelines...............................................................................20
3.5 Ferrite Core Installation and Wiring...........................................21
3.6 User Subscription/Unsubscription.............................................23
3.6.1 System ID............................................................................................. 23
3.6.2 Authentication Code ............................................................................. 24
3.6.3 User Subscription.................................................................................25
3.6.4 User Unsubscription I...........................................................................26
3.6.5 User Unsubscription II ..........................................................................27
3.6.6 RSSI Monitoring ...................................................................................28

iPECS eMG80
System DECT Installation Guide Issue 1.3
ii
4. Attendant Services............................................................29
4.1 Enable Subscription....................................................................30
4.2 Terminate a Subscription............................................................31
4.3 Authentication Code for DECT Subscription............................32
4.4 Viewing the System ID (PARK code)..........................................33
4.5 Authenticating a User..................................................................34
4.6 Modifying the System ID (PARK code)......................................35
4.7 Deleting all Subscriptions...........................................................36
4.8 Deleting a Single Subscription...................................................37
4.9 Registering to a Networked System...........................................38
5. Troubleshooting................................................................39

iPECS eMG80
System DECT Installation Guide Issue 1.3
1
1. INTRODUCTION
iPECS eMG80 DECT (Digital Euro Cordless Technology) solution employs Ericsson-LG
Enterprise DECT technology to provide convenience and enhanced productivity with increased
office mobility. With the System DECT solution, any DECT Gap compatible handset such as the
Ericsson-LG Enterprise GDC-450H/480H/500H DECT handset can use wireless connectivity for
accessing features and functions of the iPECS system. GDC-450H/480H/500H connect with
Ericsson-LG Enterprise DECT Base Stations, providing a fixed radio coverage area or cell.
Arranging multiple base stations with overlapping cells forms zones of transparent coverage. As
the handset is moved within the zone, a Radio Frequency (RF) connection can be established
with any Base station in the zone for transparent operation of the handset throughout the zone,
using active call hand-off.
Figure 1.1-1 System Connection Diagram

iPECS eMG80
System DECT Installation Guide Issue 1.3
2
2. SYSTEM DECT COMPONENTS &
SPECIFICATIONS
The System DECT solution works well with iPECS eMG80 System which is comprised of WTIB4,
Base Station (RPF), and DECT terminal. The next figure shows a general DECT reference model
of Wireless Office Terminal System (WOTS).
Figure 2.1 General DECT reference model of Wireless Office Terminal System
PABX – Private Automatic Branch Exchange
RFP – Radio Fixed Part (Base Station)
PSTN – Public Switched Telephone Network
The following is needed to configure the System using DECT phones:
WTIB4 board –One WTIB4 can be connected to the iPECS eMG80 System. WTIB4
can support up to four Base Stations.
Base Station (GDC-600BE) – The Base Station can process up to six simultaneous
calls. The Base Station should be installed indoors and protected from surge because
it is designed for indoor station.
Wireless Terminal (GDC-450H/480H/500H)– Up to 48 wireless terminals can be
registered.

iPECS eMG80
System DECT Installation Guide Issue 1.3
3
2.1 General Specifications
Table 2.1-1 Environmental Specifications
ITEM DEGREES (
℃
) DEGREES (
℉
)
Operation Temperature
0~40
32~104
Optimum Operation Temperature
20~26
68~78
Storage Temperature
10~70
32~158
Relative Humidity
0~80% non-condensing
2.2 WTIB4 Specifications
ITEM SPECIFICATION
WTIB4
Power Consumption
3.3W (= 660mA @ +5V)
DECT base station connection port
4
DECT base station interface
E1(line coding : HDB3)
DECT base station feeding voltage
+30V (±2.5%)
Serial Port for GDK-TRC1
1 (115,200bps); ELG proprietary 4-pin serial interface
2.3 GDC-600BE Specifications
Table 2.3-1 Base Station Specifications
ITEM SPECIFICATION
Power feeding +30VDC
Transmission Max Power 250mW
100mW(USA)
Access Method/Duplex TDMA/TDD
Frequency Band 1,880~1,900MHz
1920~1930MHz (USA)
Channel Spacing 1.728MHz
Modulation GFSK
Data rate 1.152Mbps
Max. Base Station distance from the WTIB4 600m (twisted 2-pair cable)

iPECS eMG80
System DECT Installation Guide Issue 1.3
4
2.4 GDC-450H/480H/500H Specifications
Battery type, battery life, charger/base input voltage and current, charger output voltage and
current, minimum receive power for operation, etc.
Table 2.4-1 Wireless Terminal Specifications
ITEM SPECIFICATION
Max. Transmission Power 250mW maximum
100mW(USA) maximum
Modulation Method GFSK
Frequency Band 1,880MHz~1,900MHz
1920~1930MHz (USA)

iPECS eMG80
System DECT Installation Guide Issue 1.3
5
3. INSTALLATION
3.1 Installation Overview
The installation of System DECT begins with a Site Survey to establish a temporary site map
including initial locations for Base Stations. After the site map is developed, the WTIB(s) is
installed and the iPECS is configured to support System DECT (refer to your system iPECS
eMG80 Administration and Programming Manual
DECT employs RF signals to communicate between the handsets and Base Stations.
for establishing DECT data in Web Admin).
Once configuration is complete, the Base Stations are mounted in their preliminary locations and
an RF coverage survey is conducted to refine the Base Station locations. With the Base Stations
placed and installed in their permanent locations, handsets can be registered to System DECT.
In order to address the variation in range, prior to installation, a site survey should be conducted
to establish a map with the preliminary locations for the DECT Base Stations. After installation,
the handset is employed in the Cell Tool mode to define the actual RF radiation pattern and Base
Station locations can be adjusted to provide seamless coverage.
3.2 Site Planning for Base Stations
The purpose of Site Planning is to provide you with information and explain tasks that should be
considered to ensure the best operation of the system. Read the following information before
installing the unit.
CAUTION
The Base Station should be installed indoors and protected from surge because it
is designed to be an indoor station.
3.2.1 Cell-coverage Region Survey (CRS)
In order to obtain the most complete coverage in your facility, this Section explains the measuring
procedures using the Cell-coverage Region Survey (CRS) tool of GDC-600TBE. The temporary
positions of Base Stations should be determined prior to this measurement according to
instructions outlined in this section. The temporary positions will be adjusted according to the
measurement findings, if necessary. Before reading this part, it is recommended to get used to
the manipulation of the CRS tool. GDC-450H/480H/500H supports CRS function.

iPECS eMG80
System DECT Installation Guide Issue 1.3
6
3.2.2 Preliminary Positions of Base Stations
1. Obtain the plane drawings of the building.
First, understand the general constructing materials of the walls, doors, windows, etc.
The materials of the building are the main factors of attenuation of the RF signals.
Figure 3.2.2-1 DECT Site Survey
As the Base Station or Handset RF signal propagates, it is subject to several
characteristics that affect the ability to receive the signal in a useable form. Normal
attenuation, reflection, and noise all contribute to signal degradation over distance. The
Base Station and Handset transmit at about 10 dbm and can receive a signal of -70
dbm. In an open field with line-of-sight, the handset and Base station can have a
separation of about 175 meters. The antenna radiation pattern is approximately circular
in the horizontal plane (shown Figure 3.2.2-2). In an office environment, walls, doors,
windows, etc. will further attenuate the RF signal to varying degrees (guidelines below),
significantly reducing the coverage area.

iPECS eMG80
System DECT Installation Guide Issue 1.3
7
Figure 3.2.2-2 Antenna Radiation Pattern
Office furniture and structures such as filing cabinets, and certain windows and other
surfaces can cause reflections of the original signal. Some materials cause significant
reflections, which can reduce the received signal. GDC-600BE has two antennas to
implement antenna diversity, which minimizes the affects of signal reflections. By
employing the antenna with the best signal, the affects of reflected signals can be
reduced. Although reflections cannot be eliminated in an office, consider locating the
Base Stations away from cabinets and other tall furniture.
High noise levels affect the ability of the receiver to separate the desired signal from the
general noise. Office and industrial equipments such as Fax machines, office
electronics, welders, microwave ovens and even poorly maintained fluorescent lighting
can generate high RF emissions, which appear as background RF noise. Also multiple
reflections of the original signal can appear as noise. Again, although RF noise cannot
be eliminated, noise can be reduced by locating Base stations away from nearby
emitters.

iPECS eMG80
System DECT Installation Guide Issue 1.3
8
2. Determine the broadcasting range of a Base Station.
In a typical office environment, the radios of the cell supported by a Base Station is
approximately 25-40 meters. These figures however, are truly dependent on the office
characteristics (ex., construction material of walls, placement of metallic objects, doors,
windows, etc.); make sure to get to know the broadcast range in your environment
taking each office characteristic into account (refer to Figure 3.2.2-3).
Figure 3.2.2-3 Sample Temporary Base Station Position
3. Mark the position of the offices where wireless handsets (450H/480H/500H) mainly will
be used, and mark the places where high call demands would exist; these areas should
be well covered by the Base Stations.
4. Roughly determine the number of Base Stations and the positions needed according to
the above tips.

iPECS eMG80
System DECT Installation Guide Issue 1.3
9
3.2.3 General Procedure for CRS
After getting well-acquainted with the operation of GDC-600TBE, and how the Base Stations
work as applicable to your facility, the CRS can be conducted. Section 3.2.2, Preliminary
Positions of Base Stations should already have been completed.
To conduct a CRS:
1. First, verify that other DECT Base Stations in the area are powered OFF; only the one
you are working with currently should be ON.
2. Enter the same PARK ID in GDC-600TBE and GDC-450H/480H/500H.
3. Mount GDC-600TBE at the determined temporary position as high as possible; it is
recommended to place GDC-600TBE at higher than 2 meters.
4. Check the Received Signal Strength Indicator (RSSI) level in GDC-450H/480H/500H by
walking around the area; decide the cell-coverage range temporarily using the pre-
determined RSSI level.
5. Repeat CRS procedure from Step 1 at the next tentative Base Station position; it is
likely and recommended that the cell-coverage will overlap a bit as shown:
Figure 3.2.3-1 Cell Boundary Map with Base 1 and Base 2

iPECS eMG80
System DECT Installation Guide Issue 1.3
10
6. If marked positions on the drawing need to be adjusted, move Base Station positions by
checking shadow area on plan drawing, and adjusting the Cell-Coverage Regions
(consider traffic of 6 calls per area, and add to plan) as shown:
Figure 3.2.3-2 Adjusting Cell Boundary Positions for Base 1 and Base 2
7. After completing the CRS, install the Base Stations (GDC-600BE) in the optimal
locations.
8. Finalize the Base Station position by performing a handover and call test with wireless
terminals (ex., 450H/480H/500H), by checking the cell coverage region with GDC-
450H/480H/500H monitor RSSI level (recommended -65 ± 5dBm, walk with 2 handsets
and monitor for voice quality).
3.2.3.1 Additional Tips for CRS
The following lists what you should keep in mind during the CRS Test:
Draw a cell-coverage region map for each Base Station temporary position.
The height of a mounted Base Station highly affects the performance of Base Station;
it is recommended Radio Fixed Parts (RFP) such as Base Stations, should be
mounted as high as possible, and at least higher than 2 meters.
It is good to locate the position of the RFP in order to secure as many line-of-sight
paths as possible, no obstacles between the RFP and Handset (PP), and the path is
direct; a line-of-sight path is a good travel way for Radio Frequency signal.
All other DECT products should be powered-OFF, and GDC-600TBEs cannot work
simultaneously.
Testing during daytime in the real environment is more recommended, as the RSSI is
very sensitive to environmental situations; testing at night when the interfering factors

iPECS eMG80
System DECT Installation Guide Issue 1.3
11
are minimized will bring quite different results from a real office environment.
If there is fading due to metal material, the RSSI value can be varied over a wide
range.
Use a fully-charged battery pack.
3.2.4 Base Station General Guidelines
Using the guidelines and examples below, determine and indicate the approximate Base station
locations on the drawing.
Maximize line-of-sight
Distance in open field 150 meters ~ -65 dbm
Distance in-office 25 to 40 meters
Distance in hallway or open factory floor 40 to 70 meters
Locate Base stations to minimize obstructions (sprinklers, exit signs, etc.)
Locate Base stations away from noise emitters (FAX machines, etc.)
Locate Base stations away from metal objects (tall filing cabinets, security/fire doors,
etc.)
Locate Base stations near the center of the desired coverage area
For proper handover, the coverage area of each Base station should overlap by 10 to
15 meters.
Consider high traffic areas such as conference rooms and cafeterias.
Each Base station supports four (4) simultaneous conversations.
Multiple Base stations can be co-located with a minimum distance of 0.25 meters.
For a multi-floor installation, plan coverage for each floor separately
Attenuation approximations considering office equipment and materials:
Open field = 0.5 db/meter
Office environment = 2 to 3 db/meter (25 ~ 40 meters)
Hall or open factory floor = 1 to 2 db/meter (40 to 70 meters)
Concrete and masonry = 15 db/cm
Windows, clear glass = 5 dbWindows, mirrored glass = 15 db
Drywall, standard = 5 db
Drywall, metal backed = 12 db
Metal, 1.5 mm = > 20db

iPECS eMG80
System DECT Installation Guide Issue 1.3
12
Figure 3.2.4-1 Hallway Placement
Figure 3.2.4-2 Centralized Base Station Placement

iPECS eMG80
System DECT Installation Guide Issue 1.3
13
Figure 3.2.4-3 Base Station Aligned with Corridor to Adjoining Area
CAUTION
1. The appropriate position for a Base Station is no closer than 1.8m above the floor
and 0.5m below the ceiling.
- The best communication environment is when a Base Station and a user are of
the same height. In an office environment, however, it is recommended to
consider office furniture (especially iron desktops or cabinets) to minimize
reflection, diffraction and scattering of DECT wave when you set the position of a
Base Station.
2. Keep away from any electronic equipment such as copy machines, printers or
computers.
3. The lower wall of a corridor where many people pass by, corner of a wall, and
narrow indoors also should be avoided.
4. When you install a Base Station on the wall, it is better to include intervals.
- DECT wave is attenuated by reflection indoors. In order to minimize attenuation,
when you install a Base Station on the wall, give at least three-wave-length
intervals. The intervals should be about 45cm because the wavelength is 15cm at
DECT frequency.
In iPECS eMG80 System, WTIB4 is Base Station interface board. iPECS eMG80 System can
have one WTIB4 (up to 4 ports).

iPECS eMG80
System DECT Installation Guide Issue 1.3
14
3.3 WTIB4
The WTIB4 can be installed on KSU.
CAUTION
1. Prior to installing the WTIB4, System power should be turned OFF to avoid any
damage.
The layout and dip switch setting of WTIB4 of iPECS eMG80 is shown:
Figure 3.3-1 WTIB4
CAUTION
The Base Station is connected to the WTIB4 by an unshielded twisted pair cable (at least
CAT3).
NOTE
The unshielded twisted pair cable (at least CAT3) should be used to connect WTIB4
with a Base Station.
Shielded cable can be used if it can withstand interference from noise sources such
as an AC power cable with high voltage. A shorter cable length and/or clear line-of-
view between the WTIB4 and Base Station will decrease the possibility of data
degradation.
Even though there are connection points such as MDF or the connection tab between
WTIB4 and Base Station, the connection points should be connected with twisted-pair
cable (at least CAT3). For example, WTIB4 to MDF, MDF to MDF, MDF to connection
tab, and connection tab to Base Station should be joined using twisted-pair cable.

iPECS eMG80
System DECT Installation Guide Issue 1.3
15
3.3.1 Pin Assignment
Table 3.3.1-1 WTIB 4
Connector Label PIN number Signal name Function Note
RJ11
WTI1
1, 6 Unused/reserved
Cell1
2 RX+(GND) Receive Data
3 TX-(+30V) Transmit Data
4 TX+(+30V) Transmit Data
5 RX-(GND) Receive Data
WTI2 The same as the above contents Cell2
WTI3 The same as the above contents Cell3
WTI4 The same as the above contents Cell4
Table 3.3.1-2 Base Station
Connector Label PIN number Signal name Function Note
RJ11 MJ1
1, 6 Unused/reserved
2 TX+(GND) Transmit Data
3 RX(+30V)
Receive Data
4 RX(+30V)
Receive Data
5
TX-(GND)
Transmit Data
NOTE
Using unshielded twisted-pair cable (more than CAT3), wire the Base Station RJ-11 to
the termination point/MDF for connection to a WTIB4.
Tag or number wiring for maintenance.
3.3.2 Connectors, Switch and LED Functions
The following table shows the relation between modular connector and associated cell numbers.
Table 3.3.2-1 Connector Functions
Connector CELL Number
MJ1-1(WTIB4)
Cell 1
MJ1-2(WTIB4) Cell 2
MJ1-3(WTIB4)
Cell 3
MJ1-4(WTIB4) Cell 4
The 4 LEDs mounted on iPECS eMG80 WTIB4 provide diagnostic information for status of the
board. The following table shows the meaning of the different LED status indicators