Ofs ELEVEN COLLABORATIVE User manual

ELEVEN COLLABORATIVE
CONFERENCE TOPS
Assembly Instructions

ELEVEN COLLABORATIVE CONFERENCE TOPS
Assembly Instructions
Table of Contents
SUPPORT BRACE ASSEMBLY........................................................... 3
TABLE BASE FRAME ASSEMBLY ........................................................ 4
LEG ATTACHMENT ................................................................... 5
TOP JOINING PLATE ASSEMBLY ........................................................ 6
TOP CLAMP/TOP SPACER INSTALLATION ................................................. 7
TOP PLACEMENT AND CONNECTION .................................................... 8
TOP ATTACHMENT ................................................................... 9

3
Completed Assembly
Outside Leg Rail
Support Brace
Flat Head Cap Screw
SUPPORT BRACE ASSEMBLY
(This step is not used on all tables)
Position Support Brace so counter-sunk holes
in Outside Leg Insert rail are aligned with holes
on end of Support Brace.
Insert Flat Head Cap Screws and tighten with
5MM allen wrench.
NOTE: Frame is assembled upside-down. Frame
is to be flipped over after legs are installed.
NOTE: This step is used only on trapezoid tables
and some boat-shaped tables.
ELEVEN COLLABORATIVE CONFERENCE TOPS
Assembly Instructions
Support Brace Assembly
THIS STEP IS NOT USED ON ALL TABLES
NOTE: Frame is assembled upside-down.
Frame is to be flipped over after legs are installed.
NOTE: This step is used only on trapezoid tables and some boat-
shaped tables.
Instructions
• Position Support Brace so counter-sunk holes in
Outside Leg Insert rail are aligned with holes on end
of Support Brace.
• Insert Flat Head Cap Screws and tighten with 5MM
allen wrench.

4
Double Top Support Rail
Single Top Support Rail
Inside Leg Insert Rail, OR
Straight Leg Insert Rail
Position Support Rail Clamp
where indicated
&
-TIGHTEN SECURELY-
Flat Head
Cap Screw
Support Rail Clamp
Position Double Top Support Rail and Single Top
Support Rail so counter-sunk holes in Inside Leg
Insert Rail are aligned with holes on end of Support
Rails.
Insert Flat Head Cap Screws and tighten with
5MM allen wrench.
TABLE BASE FRAME ASSEMBLY
(This step is not used on all tables)
Loosen bolts in Support Rail Clamp with 5MM Allen
wrench, and postion on Support Rails where indicated
on the Assembly Master Illustration.
Clamp onto Rails and - SECURELY TIGHTEN - bolts.
Install required rail on opposite end of rails.
NOTE: Frame is assembled upside-down. Frame
is to be flipped over after legs are installed.
CONFERENCE TOPS
Assembly Instructions
Table Base Frame Assembly
THIS STEP IS NOT USED ON ALL TABLES
NOTE: Frame is assembled upside-down.
Frame is to be flipped over after legs are installed.
Instructions
• Position Double Top Support Rail and Single Top Support Rail
so counter-sunk holes in Inside Leg Insert Rail are aligned with
holes on end of Support Rails.
• Insert Flat Head Cap Screws and tighten with 5MM allen
wrench.
• Loosen bolts in Support Rail Clamp with 5MM allen wrench,
and position on Support Rails where indicated on the
Assembly Master Illustration.
• Clamp onto Rails and -SECURELY TIGHTEN- bolts.
• Install required rail on opposite end of rails.
ELEVEN COLLABORATIVE

5
CONFERENCE TOPS
Assembly Instructions
Leg Attachment
NOTE: Frame is assembled upside-down.
Frame is to be flipped over after legs are installed.
USE THIS METHOD FOR:
Rectangular Tables 84” and Smaller | Trapezoid Tables Square
Tables | Round Tables | Three-legged Tables
Instructions
• Use 5MM allen wrench to loosen leg bolts.
DO NOT REMOVE BOLTS
• Slide leg between rails until leg bottoms out,
leaving no gap.
• Tighten bolts.
USE THIS METHOD FOR:
Rectangular Tables larger than 84”
Instructions
• Use 5MM allen wrench to loosen leg bolts.
DO NOT REMOVE BOLTS
• Slide leg between rails until leg bottoms out,
leaving no gap.
• Tighten bolts.
On larger tables with 6 legs, center legs are
inserted into Straight Leg Rails.
Outside Leg Rails
Loosen bolts
first!
Outside Leg
Rail
Inside Leg
Rail
Loosen bolts
first!
LEG ATTACHMENT
Use this method for:
Rectanguar tables 84" and smaller.
Trapezoid tables. Square tables.
Round tables. Three-legged tables.
Use this method for:
Rectanguar tables larger than 84".
Use 5MM allen wrench to loosen
leg bolts. DO NOT remove bolts.
Slide leg between rails until leg
bottoms out, leaving no gap.
Tighten bolts.
Use 5MM allen wrench to loosen
leg bolts. DO NOT remove bolts.
Slide leg between rails until leg
bottoms out, leaving no gap.
Tighten bolts.
On larger tables with six legs, center
legs are inserted into Straight Leg
Rails.
NOTE: Frame is assembled upside-down. Frame
is to be flipped over after legs are installed.
Outside Leg Rails
Loosen bolts
first!
Outside Leg
Rail
Inside Leg
Rail
Loosen bolts
first!
LEG ATTACHMENT
Use this method for:
Rectanguar tables 84" and smaller.
Trapezoid tables. Square tables.
Round tables. Three-legged tables.
Use this method for:
Rectanguar tables larger than 84".
Use 5MM allen wrench to loosen
leg bolts. DO NOT remove bolts.
Slide leg between rails until leg
bottoms out, leaving no gap.
Tighten bolts.
Use 5MM allen wrench to loosen
leg bolts. DO NOT remove bolts.
Slide leg between rails until leg
bottoms out, leaving no gap.
Tighten bolts.
On larger tables with six legs, center
legs are inserted into Straight Leg
Rails.
NOTE: Frame is assembled upside-down. Frame
is to be flipped over after legs are installed.
ELEVEN COLLABORATIVE

6
TOP JOINING PLATE ASSEMBLY
(This step is not used on all tables)
NOTE: All Top Joining Plates are pre-assembled
with clamps bolted in place.
120 x 42 & 120 x 48 Rectangular Tables,
66 & 72 Square Tables and Trapezoid Tables
96 x 48, 108 x 48 & 120 x 48 Boat-Shaped Tables
All Other Tables with 2 Piece Tops
Clip Top Joining Plates to inside faces of
Double and Single Support Rails.
Position Plates so they are at the mid-point
of the rails.
Tighten Clamps with 5MM allen wrench.
Clip Top Joining Plates to inside faces of
Double and Single Support Rails.
Position Plate so it is at the mid-point of
the rails.
Tighten Clamps with 5MM allen wrench.
Clip Top Joining Plates to inside faces of
Straight Leg Insert Rails (between the rails).
Slide Plates outward as far as they will go.
Tighten Clamps with 5MM allen wrench.
NOTE: Flip assembled frame over to rest on feet at this time..
CONFERENCE TOPS
Assembly Instructions
Top Joining Plate Assembly
THIS STEP IS NOT USED ON ALL TABLES
NOTE: Flip assembled frame over to rest on feet at this time.
NOTE: All Top Joining Plates are pre-assembled with
clamps bolted in place.
Instructions
120x42 & 120x48 RECTANGULAR TABLES
66 & 72 SQUARE TABLES AND TRAPEZOID TABLES
• Clip Top Joining Plates to inside faces of Double
and Single Support Rails.
• Position Plates so they are at the mid-point of
the rails.
• Tighten Clamps with 5MM allen wrench.
96x48, 108x48 & 120x48 BOAT-SHAPED TABLES
• Clip Top Joining Plates to inside faces of Double
and Single Support Rails.
• Position Plates so it is at the mid-point of
the rails.
• Tighten Clamps with 5MM allen wrench.
ALL OTHER TABLES WITH 2 PIECE TOPS
• Clip Top Joining Plates to inside faces of Straight
Leg Insert Rails (between the rails).
• Slide Plates outward as far as they will go.
• Tighten Clamps with 5MM allen wrench.
ELEVEN COLLABORATIVE

7
TOP
Top Clamp
Top Spacer
TOP CLAMP AND TOP SPACER INSTALLATION
Snap Top Clamps onto rails where shown
on Assembly Master Illustration.
Flat surface of Top Clamp faces up.
When correctly postioned, tighten Top
Clamps (without over-tightening) using
5MM allen wrench.
Peel off adhesive backers on Top
Spacers and adhere one on each leg.
CONFERENCE TOPS
Assembly Instructions
Top Clamp/Top Spacer Installation
Instructions
• Snap Top Clamps onto rails where shown on
Assembly Master Illustration.
• Flat surface of Top Clamp faces up.
• When correctly positioned, tighten Top Clamps
(without over-tightening) using 5MM allen wrench.
• Peel off adhesive backers on Top Spacers
and adhere one on each leg.
ELEVEN COLLABORATIVE

8
Top Placement and Connection
Instructions
• Place top on frame.
• Two piece tops need to be placed so there
is access to routes for Joint Fasteners on
bottom side of top.
• Connect two halves of top together using
Joint Fasteners in routed-out sections on
connecting edges.
• Tighten with 7/16” wrench.
CONFERENCE TOPS
Assembly Instructions
ELEVEN COLLABORATIVE

9
DISTANCE A
DISTANCE A
DISTANCE BDISTANCE B
TOP ATTACHMENT
Position top so it is centered on the base.
Use two #8 X 1" truss head screws per Top Clamp to secure top to base.
If needed, use the same screws to fasten Top Joining Plate to top.
DISTANCE A
DISTANCE A
DISTANCE BDISTANCE B
TOP ATTACHMENT
Position top so it is centered on the base.
Use two #8 X 1" truss head screws per Top Clamp to secure top to base.
If needed, use the same screws to fasten Top Joining Plate to top.
CONFERENCE TOPS
Assembly Instructions
Top Attachment
Instructions
• Position top so it is centered on the base.
• Use two #8 x 1” truss head screws per Top Clamp to secure top to base.
• If needed, use the same screws to fasten Top Joining Plate to top.
11.16
ELEVEN COLLABORATIVE