Ofs LeanTo User manual

LeanTo assembly instructions

2ofs.com imagine a place® 800.521.5381 Assembly instructions
LeanTo assembly instructions
Important safety instructions
When using an electrical furnishing, basic precautions should always be followed,
including the following:
This furnishing is made for commercial use only.
Read all instructions before using this furnishing:
DANGER
To reduce the risk of electrical shock:
1. Always unplug this furnishing from the electrical outlet before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids,
or disabled persons.
3. Use the furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped in water. Return the furnishing
to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Use only SJT 18 AWG cord.
8. Risk of injury. Maximum load 75 pounds.
To reduce the risk of electric shock, this furnishing has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any way.
Note – servicing is only to be performed by an authorized representative.
Servicing of double-insulated products
In a double-insulated product, two systems of insulation are provided instead of ground-
ing. No grounding means is provided on a double-insulated product, nor is a means for
grounding to be added to the product. Servicing a double-insulated product requires
extreme care and knowledge of the system, and is to be done only by qualified service
personnel. Replacement parts for a double-insulated product must be identical to the
parts they replace. A double-insulated product is marked with the words “DOUBLE INSU-
LATION” OR “DOUBLE INSULATED”. The symbol (square within a square) is also able to
be marked on the product.
Save these instructions

3ofs.com imagine a place® 800.521.5381 Assembly instructions
LeanTo assembly instructions
Shroud Installation
1. Install bracket on top/center of surround.
2. Install 1 bracket in each shroud panel, radius portion of bracket
toward the back of unit.
3. Lay unit on back, propping the top up enough to allow access
to install the upper bracket screws.
4. Slide first panel onto unit over center bracket.
5. Slide second panel into position, making sure dowels are aligned.
6. Use ratchet straps as listed in note to close gaps in panel joint.
7. Install screws to secure the shroud, from top of unit and under
unit through the base.
Tools required
1. Powered driver and phillips bit
2. ⁄ Allen wrench (preferably with a
rounded end-this would make it easier
to get the top bolts started)
3. 2 Sets of 20 FT ratchet straps
4. Protective cover material for panel
protection (thick fabric, felt or foam)
Rear view
of panel
Attach bracket
with ¼-20 flat
screw head
Rear view of unit

4ofs.com imagine a place® 800.521.5381 Assembly instructions
LeanTo assembly instructions
Shroud Installation (Continued)
1. Use ratchet straps horizontally around top and bottom of the shroud panels to close
them together before screw installation make sure all dowels align. to avoid damage
make sure all edges and faces are covered with a protective material.
Tools required
1. Powered driver and phillips bit
2. ⁄ Allen wrench (preferably with a
rounded end-this would make it easier
to get the top bolts started)
3. 2 Sets of 20 FT ratchet straps
4. Protective cover material for panel
protection (thick fabric, felt or foam)
Rear view of unit
Install ¼-20 x 1½
truss head screw
Bottom view
of unit
Rear view
of unit
Attach bracket
with ¼-20 flat
head screw