Ofs LeanTo User manual

LeanTo Tablet Assembly

2ofs.com imagine a place® 800.521.5381 Assembly instructions
LeanTo tablet assembly
Important safety instructions
When using an electrical furnishing, basic precautions should always be followed,
including the following:
This furnishing is made for commercial use only.
Read all instructions before using this furnishing:
DANGER
To reduce the risk of electrical shock:
1. Always unplug this furnishing from the electrical outlet before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids,
or disabled persons.
3. Use the furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped in water. Return the furnishing
to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Use only SJT 18 AWG cord.
8. Risk of injury. Maximum load 75 pounds.
To reduce the risk of electric shock, this furnishing has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any way.
Note – servicing is only to be performed by an authorized representative.
Servicing of double-insulated products
In a double-insulated product, two systems of insulation are provided instead of ground-
ing. No grounding means is provided on a double-insulated product, nor is a means for
grounding to be added to the product. Servicing a double-insulated product requires
extreme care and knowledge of the system, and is to be done only by qualified service
personnel. Replacement parts for a double-insulated product must be identical to the
parts they replace. A double-insulated product is marked with the words “DOUBLE
INSULATION” OR “DOUBLE INSULATED”. The symbol (square within a square) is also
able to be marked on the product.
Save these instructions

3ofs.com imagine a place® 800.521.5381 Assembly instructions
LeanTo tablet assembly
Outside View
Cut small X
on these
3 holes from
outside
Use an icepick
or regulator
to locate these
6 holes
Cut small X on these
3 holes from inside,
located with icepick/
regulator.
Note: Some tablet
configurations do
not require the inside
holes to be cut out.
1.780698
15.376968
2.5
Inside View
2.5
LeanTo tablet bracket install
1. Before cutting any holes, check tablet and specific instructions
for bracket locations needed.
.90625

4ofs.com imagine a place® 800.521.5381 Assembly instructions
LeanTo tablet assembly
Inside ViewOutside View
Install with
¼-20 X ¾"
flat head
screws
Outside Bracket
LeanTo tablet bracket install - continued
1. Before cutting any holes, check tablet and specific instructions
for bracket locations needed.
Inside Bracket

5ofs.com imagine a place® 800.521.5381 Assembly instructions
LeanTo tablet assembly
¼-20 X ¾"
Flat head
screws
89T2 UR
Option Shown
89TR Shown
LeanTo tablet bracket install - continued

6ofs.com imagine a place® 800.521.5381 Assembly instructions
LeanTo tablet assembly
89GS Bracket location
Bottom
view
Outside brackets
8 x 1 ¼"
Flat head
screw

7ofs.com imagine a place® 800.521.5381 Assembly instructions
LeanTo tablet assembly
89GT2 Bracket location
Bottom
view
8 x 1 ¼"
Flat head
screw
Outside
brackets
Inside brackets

8ofs.com imagine a place® 800.521.5381 Assembly instructions
LeanTo tablet assembly
89GT1 Bracket location
Bottom
view
Outside
brackets
8 x 1 ¼"
Flat head
screw
Inside
brackets
UQ position

9ofs.com imagine a place® 800.521.5381 Assembly instructions
LeanTo tablet assembly
Bottom
view
Outside
brackets
8 x 1 ¼"
Flat head
screw
Inside
brackets
89GT1 Bracket location
UR position

10ofs.com imagine a place® 800.521.5381 Assembly instructions
LeanTo tablet assembly
89T1 Installation
8 x ¾"
Flat head
wood screw
Bore 2 holes
.125" down to .5"
Template - fold line over side and bottom edge

11ofs.com imagine a place® 800.521.5381 Assembly instructions
LeanTo tablet assembly
89T1 Installation
8 x 1 ¼"
Flat head
screw
¼-20 x ½”
Pan head
screws
¼-20 x ¾"
Flat head
screws