Ofs Kintra User manual

Kintra assembly instructions

2ofs.com imagine a place® 800.521.5381 Assembly instructions
Kintra assembly instructions
Important safety instructions
When using an electrical furnishing, basic precautions should always be followed,
including the following:
This furnishing is made for commercial use only.
Read all instructions before using this furnishing:
DANGER
To reduce the risk of electrical shock:
1. Always unplug this furnishing from the electrical outlet before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids,
or disabled persons.
3. Use the furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped in water. Return the furnishing
to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Use only SJT 18 AWG cord.
8. Risk of injury. Maximum load 75 pounds.
To reduce the risk of electric shock, this furnishing has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any way.
Note – servicing is only to be performed by an authorized representative.
Servicing of double-insulated products
In a double-insulated product, two systems of insulation are provided instead of
grounding. No grounding means is provided on a double-insulated product, nor is a
means for grounding to be added to the product. Servicing a double-insulated product
requires extreme care and knowledge of the system, and is to be done only by qualified
service personnel. Replacement parts for a double-insulated product must be identical to
the parts they replace. A double-insulated product is marked with the words “DOUBLE
INSULATION” OR “DOUBLE INSULATED”. The symbol (square within a square) is also
able to be marked on the product.
Save these instructions

3ofs.com imagine a place® 800.521.5381 Assembly instructions
Kintra assembly instructions
Kintra table tops will be shipped in one of these ways:
STEP 1
1. Place top, face side down, on a non marring surface.
2. Remove shipping screws from bottom covers and place bottom covers to the side.
STEP 1 (shelf option)
1. Place top, face side down, on a non marring surface.
2. Remove shipping screws from shelf bottom and place to the side.
3. Remove shipping screws from shelf assembly and place to the side.
No shelf option With shelf option
84" or larger table
Shelf bottom
Shelf assembly

4ofs.com imagine a place® 800.521.5381 Assembly instructions
Kintra assembly instructions
Installation (Continued)
STEP 2
1. Connect end panels to top by pressing mitered edge of end panel to
the mitered edge of top.
2. Use 12 (per leg) #8 x 1½" pan head screws (HK-15) to secure table legs to top.
Numbers must match
IMPORTANT!!
Tops and ends are in numbered sets.
The numbers are on the angled faces
of the tops and ends. The number on
the end MUST match the number on
the top. DO NOT switch ends.
Use four (4) #8 x 1½" pan head screws
to screw support beams to ends (both ends)
(HK-15).
On 42" tall versions (KTH) use ten (10)
⅜-16 X 1 hex head bolts to attach support
beam brackets to ends (both ends) (HK-147).
1A
1A
1B

5ofs.com imagine a place® 800.521.5381 Assembly instructions
Kintra assembly instructions
Installation (Continued)
STEP 3
1. Replace bottom covers and secure with #8 x ¾" flat head screws (HK-53).
2. Flip table over and place in desired location.
STEP 3 (shelf option)
1. Replace shelf assembly and screw to top.
2. Use #8 x ¾" flat head screws (HK-53) on cover panels.
3. Use #8 x 2" pan head screws (HK-92) on divider panels.
4. Use #8 x 1¼" flat head screws (HK-48) to screw trough to shelf
assembly back panel.
5. Replace shelf bottom and use #8 x 1¼" flat head screws
(HK-48) to screw shelf bottom to shelf assembly.
6. Insert shelf supports into pre-drilled holes in end panels (see
detail). Use # 6 x ⅝" flat head screws (HK-134) to secure.
Detail
Cover panel
Dividers panels
Back panel
Trough
Shelf bottom