Ofs Zero User manual

Zero assembly instructions

2ofs.com imagine a place® 800.521.5381 Assembly instructions
Zero assembly instructions
Important safety instructions
When using an electrical furnishing, basic precautions should always be followed,
including the following:
This furnishing is made for commercial use only.
Read all instructions before using this furnishing:
DANGER
To reduce the risk of electrical shock:
1. Always unplug this furnishing from the electrical outlet before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids,
or disabled persons.
3. Use the furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped in water. Return the furnishing
to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Use only SJT 18 AWG cord.
8. Risk of injury. Maximum load 75 pounds.
To reduce the risk of electric shock, this furnishing has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any way.
Note – servicing is only to be performed by an authorized representative.
Servicing of double-insulated products
In a double-insulated product, two systems of insulation are provided instead of ground-
ing. No grounding means is provided on a double-insulated product, nor is a means for
grounding to be added to the product. Servicing a double-insulated product requires
extreme care and knowledge of the system, and is to be done only by qualified service
personnel. Replacement parts for a double-insulated product must be identical to the
parts they replace. A double-insulated product is marked with the words “DOUBLE INSU-
LATION” OR “DOUBLE INSULATED”. The symbol (square within a square) is also able to
be marked on the product.
Save these instructions

3ofs.com imagine a place® 800.521.5381 Assembly instructions
Zero assembly instructions
Table of Contents
2
3
4
5
Important safety instructions
Table of contents
Chair assembly
Seat cover installation

4ofs.com imagine a place® 800.521.5381 Assembly instructions
Zero assembly instructions
Chair assembly
Tools required:
• 8mm allen wrench
BASE
SEAT PLUG
STACKING SHIELD
SEAT
BACK
FASTENER
BASE SPACER
CHAIR ASSEMBLY
FASTENER
BASE SPACER
SEAT
SEAT FOAM
FABRIC
SEAT PLUG
FABRIC DRAWSTRINGS
TOOLS NEEDED:
8MM ALLEN WRENCH
SEAT COVER INSTALLATION
ALIGN / NEST SEAT COMPONENTS TOGETHER AND INSTALL 1.
FASTENER. HAND TIGHTEN ONLY.
PULL DRAWSTRINGS TIGHT AND TIE THEM IN A KNOT. 2.
DISASSEMBLE FASTENER AND SEAT PLUG. 3.
FOLLOW CHAIR ASSEMBLY INSTRUCTIONS TO INSTALL SEAT. 4.

5ofs.com imagine a place® 800.521.5381 Assembly instructions
Zero assembly instructions
Seat cover installation
1. Align/nest seat components together and install fastener. Hand tighten only.
2. Pull drawstrings tight and tie them in a knot
3. Dissassemble fastener and seat plug
4. Follow chair assembly instructions to install seat
Tools required:
• 8mm allen wrench
BASE
SEAT PLUG
STACKING SHIELD
SEAT
BACK
FASTENER
BASE SPACER
CHAIR ASSEMBLY
FASTENER
BASE SPACER
SEAT
SEAT FOAM
FABRIC
SEAT PLUG
FABRIC DRAWSTRINGS
TOOLS NEEDED:
8MM ALLEN WRENCH
SEAT COVER INSTALLATION
ALIGN / NEST SEAT COMPONENTS TOGETHER AND INSTALL 1.
FASTENER. HAND TIGHTEN ONLY.
PULL DRAWSTRINGS TIGHT AND TIE THEM IN A KNOT. 2.
DISASSEMBLE FASTENER AND SEAT PLUG. 3.
FOLLOW CHAIR ASSEMBLY INSTRUCTIONS TO INSTALL SEAT. 4.