Ofs Heya User manual

Heya assembly instructions

2ofs.com imagine a place® 800.521.5381 Assembly instructions
Heya assembly instructions
Important safety instructions
When using an electrical furnishing, basic precautions should always be followed,
including the following:
This furnishing is made for commercial use only.
Read all instructions before using this furnishing:
DANGER
To reduce the risk of electrical shock:
1. Always unplug this furnishing from the electrical outlet before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking o parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalids,
or disabled persons.
3. Use the furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped in water. Return the furnishing
to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Use only SJT 18 AWG cord.
8. Risk of injury. Maximum load 75 pounds.
To reduce the risk of electric shock, this furnishing has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any way.
Note – servicing is only to be performed by an authorized representative.
Servicing of double-insulated products
In a double-insulated product, two systems of insulation are provided instead of ground-
ing. No grounding means is provided on a double-insulated product, nor is a means for
grounding to be added to the product. Servicing a double-insulated product requires
extreme care and knowledge of the system, and is to be done only by qualified service
personnel. Replacement parts for a double-insulated product must be identical to the
parts they replace. A double-insulated product is marked with the words “DOUBLE INSU-
LATION” OR “DOUBLE INSULATED”. The symbol (square within a square) is also able to
be marked on the product.
Save these instructions

3ofs.com imagine a place® 800.521.5381 Assembly instructions
Heya assembly instructions
Heya Booth: Single media screen
Deuce foot install
Make sure units
are square to each
other to ensure
proper assembly.
36"
REF
102"
REF
Top view

4ofs.com imagine a place® 800.521.5381 Assembly instructions
Heya assembly instructions
Heya Booth: Single media screen
Align all 4 connector slides on
wall with connector posts on the
surround and push down.


If using HDMI, RJ45 or VGA accessory for
power supply, must install before table
bracket. To access power supply, remove
4 screws that attach wire manager.
Glides on wall should be close to
floor when connected properly.
Adapter plates for accessories
located inside of wire manager
16.25" +/- .25" when
connected properly.

5ofs.com imagine a place® 800.521.5381 Assembly instructions
Heya assembly instructions
Heya Booth: Table install
Side view

6ofs.com imagine a place® 800.521.5381 Assembly instructions
Heya assembly instructions
Heya single media screen
1. Install bracket to wall


2. Install leg to table
Bottom view
Turn angle of leg toward front of table top
Hole locations for
table brackets
Table bracket
¼ - 20 x ¾"
Truss head (X6)
2.5"
2.43"
12.95"
22.66"
¼ - 20 x ¾"
Flat head (X6)



7ofs.com imagine a place® 800.521.5381 Assembly instructions
Heya assembly instructions
3. Install table to wall
Bottom view
Heya single media screen

¼ - 20 x ¾"
Truss head (X5)

8ofs.com imagine a place® 800.521.5381 Assembly instructions
Heya assembly instructions
Heya table install to DS & SS media screens
(DS application shown)
1. Install table bracket
For SS model screen:
¼ - 20 x ¾" truss head screw
For DS model screen:
¼ - 20 x 1 ¼" truss head screw
2. Install table legs
Leg location
¼ - 20 x ¾"
Flat head screw

9ofs.com imagine a place® 800.521.5381 Assembly instructions
Heya assembly instructions
Heya table install to DS & SS media screens
(DS application shown)
3. Install table
¼ - 20 x ¾"
Truss head screw

10ofs.com imagine a place® 800.521.5381 Assembly instructions
Heya assembly instructions
Heya DS media screen foot install
⅜ - 16 x 1.5"
Flat socket
cap screw
DLT foot option
DFG/DFC foot option
⅜ - 16 x 2.25"
Hex head bolt
with ⅜" flat washer

11ofs.com imagine a place® 800.521.5381 Assembly instructions
Heya assembly instructions
Heya single media screen
Deuce foot install
⅜ - 16 x 3 ½" Bolt
⅜" Washer
⅜ - 16 Hex nut
nylon locking